• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.10a
• /
• pp.36-39
• /
• 2000

This paper presents the technology of condition diagnosis & life estimation on insulation system of the traction motor. In the non-destructive methods for diagnosis of coil insulation state, residual dielectric strength is estimated by the D-map which consist of the partial discharge quantity Q and average degradation degree $\Delta$. In the operating history of machine, the N-Y life estimation method is based on the stop-starting numbers and operating times with considering each degradation factor by the thermal, electrical and heat-cycle stress. With the on-line conditioning monitoring on the currents of traction motors, detecting the abnormal operating state due to bearing faults, stator or armature faults, eccentricity related faults and broken rotor bars can be performed.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.56 no.2
• /
• pp.289-294
• /
• 2007

This paper describes the effects of rotor eccentricity in squirrel cage induction machines. Asymmetric electro-magnetic force caused by the frictional worn bearing, rotor misalignment and unbalanced rotor etc. generates an asymmetrical operation, vibration and electro-magnetic noise. The need for detection of these rotor eccentricities has pushed the development of monitoring methods with increasing sensitivity and noise immunity. In this paper, we focus on investigating the asymmetrical operation considering of unbalanced magnetic pull in squirrel-cage induction motor with 380 [V], 7.5 [kW], 4P, 1,768 [rpm]. The effects of the non-symmetric rotor and magnetic force are simulated by finite element method (FEM) and tested using search coils for measuring the actual air-gap flux.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2000.04a
• /
• pp.691-696
• /
• 2000

Cooling characteristics of cooling jacket for spindle system with built-in motor are studied. Three dimensional model was selected for the analysis of the helical-type cooling jacket. This model includes the estimation on the amount of heat generation from bearing and built-in motor and the thermal characteristic values such as heat flux on the boundary. The temperature distributions are analyzed and the cooling by Nusselt number and total heat transfer coefficient. Numerical results show that stream-wise cross section area and flow rate are important factors for cooling characteristics of cooling jacket.

• The Journal of Korean Physical Therapy
• /
• v.14 no.4
• /
• pp.441-453
• /
• 2002

The purpose of this study was to characterize lesion development, neural plasticity, and motor learing after spinal cord injury. Facilitatory intervention such as weight bearing and locomotor training after SCI may be more effective than compensatory strategies at inducing neuroplasticity and motor recovery. Minimal tissue sparing has a profound impact on segmental systems and recovery of function Spinal animal could functional locomotion when subjected to repetitive stimulation. task-specific learning of isolated lumbar spinal could improve motor performance more then other task learning.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.816-821
• /
• 2013

This case study presents a practical method to reduce resonant vibration of generator-motor set. The generator is driven at 1800rpm by induction integral motor. The vibration is below alarm limits, but the dominant frequency of vibration is sub-synchronous and close to that of bearing fault signal in spite of new bearings. To find an mechanism of abnormal vibration, ODS and Modal analysis is carried out. The measured modal characteristics were compared with those of FE Analysis. The ODS mode at rated speed is consistent with system natural frequency mode that is excited by bearings. To reduce vibration level, the isolation mount at system base is changed with new rubber mount for lower natural frequency.

• Journal of Power System Engineering
• /
• v.11 no.1
• /
• pp.20-27
• /
• 2007

In this paper, finite element modeling was performed for vibration analysis of a rotor system installed in sunroof motor, and analysis process was developed for natural frequency and unbalance response analysis. At the same time, to reduce analysis modeling error caused by the difference between analysis and measured values, finite element model updating was conducted using an optimization algorithm, i.e. hybrid genetic algorithm and simulated annealing (HGASA) method. For this end experimental modal test was carried out and by using the measured frequency response function (FRF), model updating was performed considering both cases where core coil was removed and included. And acceptable result was obtained. Also, dynamic property coefficient of bush bearing which influences vibration response of the rotor system was estimated.

• Journal of the Korean Society of Safety
• /
• v.7 no.2
• /
• pp.42-46
• /
• 1992

The submersible motor pump could have much more merits than the general pump such as higher exhaustion head, narrower installahon place, lower noise due to operating in the water and so on. But, so far, hydraulic mechanism of the axial thrust at impeller was not analysed quantitatively and so it is very difficult to solve the occuring problems. Therefore, in this study, we aimed to minimize the axial thrust acting on thrust bearing of submersible motor pump through the analysis of hydraulic mechanism of thrust and design rivision of impeller. Test carried out on the pump with an impeller 92mm in diameter, 6 balacing holes 10mm in diameter, showed the thrust is reduced by about 86％ at the normal operating point.

• Proceedings of the KIEE Conference
• /
• 2000.07b
• /
• pp.611-613
• /
• 2000

Rotor eccentricity exists extensively in BLDC motors because of manufacturing imprecision or bearing defects. In this paper, magnetic fields of a BLDC motor with static rotor eccentricity are analyzed by the time- stepping finite element method. Torque ripple, cogging torque, winding current, counter-em! and unbalanced magnetic force characteristics are obtained. These results are compared with those of a non-eccentric BLDC motor.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.10a
• /
• pp.429-435
• /
• 2002

In order to manufacture a precision mold/die by machining, users need high speed & precision mold/die machining center. So, for development of this machine, we intend to use linear motor that is instead of ball-screw, servo-motor and coupling, high-speed spindle of pressurized air journal bearing and composite materials. In this paper we research column moving type and table moving type. The former is mainly piling 3 axes on one moving body, the latter is consist of two independent carriages. Both types are available to high speed & precision machine, but we finally draw a conclusion column moving type due to an advantage of high-speed control of linear motor.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.6
• /
• pp.8-14
• /
• 2001

We develop a method to analyze dynamic behavior off multi-stage gear train system. The example system consists of three shafts supported by ball bearings at the ends of them and two pairs of spur gear set. For exact analysis, the meshing tooth pair of gear set is modeled as spring and damper having time-dependent meshing stiffness and damping. The bearing is modeled as spring. The result of this analysis is compared to that of other model having mean mesh stiffness. The effect of the excitation force by the unbalance off rotor off motor is also analyzed. Finally, the change ova natural frequency of the whole system due to the change of an angle between three shafts is compared in each case, and from this analysis, the avoiding angle for design is advised.