• Journal of Institute of Control, Robotics and Systems
• /
• v.10 no.3
• /
• pp.225-231
• /
• 2004

Disturbance observer (DOB) has been studied extensively and applied to many motion control fields during the last decades, but relatively few studies have been devoted to the development of analytic, systematic design methods for DOB itself, This paper thus aims to provide an analytic, systematic design method for DOB. To do this, DOB is structurally analyzed and the generalized disturbance compensation framework named robust internal-loop compensator (RIC) is introduced. Through this, the inherent equivalence between DOB and RIC is found, and the mixed sensitivity optimization problem of DOB is solved. Q-filter design is completely separated from the mixed sensitivity optimization problems of DOB although the proposed method has implicit .elation with Q-filter. Also, although the Q-fille. is separately designed with sensitivity function, the proposed DOB framework has the exactly same characteristic as the original DOB.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.63-67
• /
• 2004

The problem is improving the positioning precision of a permanent magnet linear synchronous motor (PMLSM). Thus, this paper presents the design and realization of an adaptive dither to reduce the force ripple in PMLSM. A composite control structure is used, consisting of three components: a simple feed-forward component, a PID feedback component and an adaptive feed-forward compensator (AFC). Especially adaptive feed-forward component cancel out detent force using wavelet transformation. Computer simulation results verify the effectiveness of the proposed scheme for high precision motion trajectory tracking using the PMLSM

• Journal of the Korean Society for Precision Engineering
• /
• v.29 no.1
• /
• pp.79-86
• /
• 2012

This paper proposes PID and RIC (Robust Internal-loop Compensator) based motion controller using dual learning algorithm for position control of linear synchronous motor respectively. Its gains are auto-tuned by using two learning algorithms, reinforcement learning and neural network. The feedback controller gains are tuned by reinforcement learning, and then the feedforward controller gains are tuned by neural network. Experiments prove the validity of dual learning algorithm. The RIC controller has better performance than does the PID-feedforward controller in reducing tracking error and disturbance rejection. Neural network shows its ability to decrease tracking error and to reject disturbance in the stop range of the target position and home.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.28 no.5
• /
• pp.603-609
• /
• 2004

This paper deals with the issue of Neural Network-based control for a rodless pneumatic cylinder system which is utilized for a pneumatic XY-plotter. In order to identify the system design parameters, the open loop response of a pneumatic rodless cylinder controlled by a pneumatic servovalve is investigated by applying a self-excited oscillation method. Based on the system design parameters, the PD feedback compensator is designed and then Neural Network is incorporated with it. The experiment of a trajectory tracking control using a PD-NN has been performed and proved its excellent performance by comparing with that of a PD feedback compensator.

• Journal of the Korean Society for Precision Engineering
• /
• v.28 no.12
• /
• pp.1379-1387
• /
• 2011

A PID-feedforward controller and Robust Internal-loop Compensator (RIC) based on reinforcement learning using random variable sequences are provided to auto-tune parameters for each controller in the high-precision position control of PMLSM (Permanent Magnet Linear Synchronous Motor). Experiments prove the well-tuned controller could be reduced up to one-fifth level of tracking errors before learning by reinforcement learning. The RIC compared to the PID-feedforward controller showed approximately twice the performance in reducing tracking error and disturbance rejection.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.6
• /
• pp.1-8
• /
• 2020

This paper proposes a method for measuring friction forces and creating a friction model for a rotary motion control system as well as an autonomous vehicle testbed. The friction forces versus the velocity were measured, and the viscous friction, Coulomb friction, and stiction were identified. With a nominal PID (proportional-integral-derivative) controller, we observed the adverse effects due to friction, such as excessive steady-state errors, oscillations, and limit-cycles. By adding an adequate friction model as part of the augmented nonlinear dynamics of a plant, we were able to conduct a simulation study of a motion control system that well matched experimental results. We have observed that the implementation of a model-based friction compensator improves the overall performance of both motion control systems, i.e., the rotary motion control system and the Altino testbed for autonomous vehicle development. By utilizing a better simulation tool with an embedded friction model, we expect that the overall development time and cost can be reduced.

• Journal of the Korean Society for Precision Engineering
• /
• v.26 no.12
• /
• pp.69-77
• /
• 2009

In this study an ANFIS-based trajectory tracking motion control algorithm is proposed for autonomous garage and parallel parking of a model car. The ANFIS controller is trained off-line using data set which obtained by Mandani fuzzy inference system and thereby the processing time decreases almost in half. The controller with a steering delay compensator is tuned through simulations performed under MATLAB/Simulink environment. Experiments are carried out with the model car for garage and parallel parking. The experimental results show that the trajectory tracking performance is satisfactory under various initial and road conditions

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.6 s.171
• /
• pp.76-82
• /
• 2005

In this paper, the pole placement controller based on the Robust Internal-loop Compensator (RIC) structure, which has inherent structural equivalence to disturbance observer, is proposed to control a linear positioning system. This controller has the advantage to easily select controller gains by using pole placement without loss of that of original RIC structure. The principal is to construct the pole placement controller for a nominal internal model instead of unknown real plant. Using linear motion experiment showed the effectiveness of the proposed controller.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.95.2-95
• /
• 2001

Disturbance observer(DOB) based controller design is one of the most popular methods in the field of motion control. In this paper, a generalized disturbance compensation framework, called as robust internal-loop compensator(RIC) is introduced and an advanced design method of DOB is proposed based on the RIC. Mixed sensitivity optimization problem, which is the main issue of DOB design, is solved through the parameterization of DOB in the RIC framework. Different from conventional methods, Q-filter is separated in the mixed sensitivity optimization problem and the systematic design law for the DOB is proposed. This guarantees the robustness and optimality of the DOB and also enables the design for unstable plants.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.11
• /
• pp.1094-1102
• /
• 2008

Through the motion control experiment using Industrial Emulator(Model 220 by ECP), the performance comparison of three kinds of controllers such as PID, RIC and LQR was carried out. It was shown that RIC has the best performance in the presence of disturbances such as step one, sinusoidal one and Coulomb friction for the rigid body. LQR using feedback state variables has the best tracking performance far the flexible body. The performance of PID controller is low compared to other controllers, but the design process is simple. The most advanced controller is LQR. In order to attenuate disturbance, an additional state observer should be used to estimate it, making more complex control system. RIC lies between PID and LQR in view of complexity of design. Even though RIC is not complicated, it has good disturbance rejection ability and less tracking error. By considering these aspects, the RIC is suggested as high precision controller to be used in motion control system.