• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.7
• /
• pp.717-728
• /
• 2009

In the field of rocket propulsion system hydrogen peroxide has been used as mono-propellant and as the oxidizer of bi-propellants. At the beginning, hydrogen peroxide was used as mono-propellant for thrusters, but later it had been replaced by hydrazine, which has better specific impulse and storability. On the other hand, to drive turbo-pumps, hydrogen peroxide is still being utilized. As the oxidizer of bi-propellants it was used until 1970's and from 1990's hydrogen peroxide once again got back to developer's interest, because one of the recent development purposes of rocket propulsion system is low-cost and ecologically-clean. Until now the storability of hydrogen peroxide has been remarkably improved. The combination of Kerosene/$H_2O_2$ also shows similar accelerating performance to Kerosene/$LO_x$ combination because of higher propellant density and higher O/F ratio, even though the propulsion performance is not as good as the combination of Kerosene/$LO_x$. Moreover, its combustion products are much cleaner than Kerosene/$LO_x$ combination.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.221-224
• /
• 2010

Recently, due to the enormous cost for sending a satellite into an orbit, small and more reliable satellites have been more demanded. An introduction of new binders(HTPB, GAP) and new oxidizers made great improvements of the large thrust modulation. In order to make cost reduction, one prefers to the low melting temperature thermoplastic propellant reforming the manufacturing process dramatically. Solid propellant rockets have been had a problem of the injection accuracy into orbit, but PBS(Post Boost Stage) using a liquid mono-propellant improves the injection accuracy. This paper also gives the direction of the advanced nozzle materials and the motor case.

• 한국전산유체공학회:학술대회논문집
• /
• 2009.04a
• /
• pp.130-134
• /
• 2009

CFD analysis of the fuel injection pattern and the flow field surrounding the liquid propellant injector of a small thruster is performed. A good agreement is shown with PIV test data for the initial configuration. Analysis on various injector shapes is performed to observe the effect of injector shape on the trajectories of liquid droplet. A various shapes of injector is investigated to enhance spray pattern of the small injector.

• International Journal of Aerospace System Engineering
• /
• v.2 no.2
• /
• pp.1-5
• /
• 2015

The powder propellant rocket which uses micron-sized particles as fuel is storable and costly. Functions like thrust control and multiple-ignition can be realized by changing powder mass flow rate. In this paper, we discuss the theoretical performance of bi-propellant and mono-propellant powder rocket. When used as the fluidization gas, helium can improve specific impulse dramatically. The stability of the powder feeding device is preliminarily quantified through metal/N2O powder rocket hot fire tests.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.4
• /
• pp.46-58
• /
• 2010

Hydrogen peroxide(HP) and liquid methane have deserved renewed considerations as green propellants in recent years, because main design concerns in the development of the new generation propulsion system for spacecrafts are concentrated on low operation cost and environmental cleanness. Although HP has a long history of application to aerospace propulsion systems due to high density, mono-propellant characteristics and low toxicity, it had been replaced by hydrazine and liquid oxygen due to extreme performance requirement during the cold war. But HP has received a renewed interest due to its increased stability and many researches have been conducted to develop high performance LREs(Liquid Rocket Engines) using HP. Liquid methane has also received a new interest in rocket propulsion system for the future space exploration according to its possibility of ISRU(In-Situ Resource Utilization).

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.2
• /
• pp.32-38
• /
• 2004

A comprehensive understanding is given for the hot-firing test results, which were obtained throughout the verification program of mono-propellant hydrazine rocket engines (thrusters) producing 0.95 lbf (4.2 N) of nominal steady-state thrust at an inlet pressure of 350 psia (2.41 Mpa). A scrutiny for the engine performance is made in terms of thrust and temperature behavior of steady state firing mode at the given propellant injection pressures: Pinj = 400, 250, 100, and 50 psi. The thrust and specific impulse are compared with a reference performance of 1-lbf standard rocket engines and their normalization procedure is introduced. A practical engineering approach to the data measurement and reduction is addressed, too.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.61-64
• /
• 2008

For the performance evaluation of liquid mono-propellant thruster, Vacuum Hot-fire test is necessarily required. An accurate flow measurement is one of the key parameters to the successful T&E program. This paper describes the characteristics of the coriolis flowmeter, explains the cold-flow test using simulant propellant (DIW), and presents the test results. Finally, the cold test results have been verified in comparison with the hot-fire test data.

• Applied Chemistry for Engineering
• /
• v.30 no.5
• /
• pp.591-596
• /
• 2019

A recently developed propellant, ammonium dinitramide (ADN, $NH_4N(NO_2)_2$ is stable and safe at an ambient condition. However, it requires high purity for practical applications. A very little quantity of foreign impurities in ADN may cause clogging of thruster nozzles and catalyst poisoning for the use of a liquid propellant. Thus, several purification processes for precipitated ADN particles such as repetition extraction, activated carbon adsorption and low-temperature extraction were presented in this study. The purifying methods helped to improve the chemical purity as evaluated by FT-IR and UV-Vis spectroscopy in addition to ion chromatography (IC) analyses. Among the purification processes, adsorption was found to be the best, showing a final purity of 99.8% based on relative quantification by IC. Thermal analysis revealed an exothermic temperature of $148^{\circ}C$ for the synthesized liquid monopropellant, but rose to $188^{\circ}C$ when urea was added.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.35-41
• /
• 2012

Liquified hydrogen peroxide as a monopropellant is drawing an attention as a power generating energy source for a machine requiring simple and light weight structure. The liquified hydrogen peroxide is attracted due to its outstanding applicability because it doesn't require an oxidizer and discharge a hazardous product. For the further industrial applications, however, a feasibility study should be carried out carefully in the aspect of the specific power density. In this study, a prototype of vane motor driven by the liquified hydrogen peroxide with high density of upper 95% was developed and its performance characteristic such as a specific power density was estimated via measuring pressure and rotation speed of the vane motor. The specific power density obtained by numerical simulation using FSI analysis supported by experimental results was up to $0.02kW/kg_{f}$, which reaches at the level of the latest developed fuel cell.

• 한국전산유체공학회:학술대회논문집
• /
• 2006.10a
• /
• pp.101-105
• /
• 2006

The computational fluid dynamic analysis has been conducted for the thermo-chemical flow field in an arcjet thruster with mono-propellant Hydrazine (N2H4) as a working fluid. The Reynolds Averaged Navier-Stokes (RANS) equations are modified to analyze compressible flows with the thermal radiation and electric field. The Maxwell equation, which is loosely coupled with the fluid dynamic equations through the Ohm heating and Lorentz forces, is adopted to analyze the electric field induced by the electric arc. The chemical reactions of Hydrazine were assumed to be infinitely fast due to the high temperature field inside the arcjet thruster. The chemical and the thermal radiation models for the nitrogen-hydrogen mixture and optically thick media respectively, were incorporated with the fluid dynamic equations. The results show that performance indices of the arcjet thruster with 1kW arc heating are improved by amount of 180% in thrust and 200% in specific impulse more than frozen flow. In addition to thermo-physical process inside the arcjet thruster is understood from the flow field results.