• Journal of the Korean Institute of Gas
• /
• v.15 no.6
• /
• pp.8-13
• /
• 2011

All over the nation, a lot of industrial complex utilize gas as their energy source. Possibilities are fire, explosion, and leakage could happen any time in these large complexes. To prevent these tragic accidents and to minimize the damage when the accident occurs, the development of diagnostic technology for these facilities is imperative. The safety check is conducted on an individual and partial basis, currently. Accordingly, the accumulation and improvement of the safety management technology is necessary in order to make all the different checking techniques and management systems compatible, since checking processes, result interpretation techniques, and subsequent prognoses are not the same. The program provides damage scenarios from gas leakage. The output enables policy makers to predict the degree of infliction. Through this program, engineers are able to design an effective gas safety program to operate and maintain ubiquitous gas facilities.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.49 no.2
• /
• pp.1-8
• /
• 2012

This paper presents the accelerometer which is a key component of TPMS(Tire Pressure Monitoring System). Generally a piezoresistive accelerometer has characteristics of lower cost, better linearity and better immunity about the environmnet noise than a capacitive one. Three types of piezoresistive accelerometers are degined and simulated using ANSYS program. The best one is a piezoresistive sensor which is supported by four beams located at the center of the edge of the mass after comparing the characteristics of resonant frequency of the three types. Considering the sensor size and a simulated maximum stress and maximum displacement, the length of beams is set as $200{\mu}m$. The size of a piezoresistive accelerometer is $3.0mm{\times}3.0mm{\times}0.4mm$. The sensor output is characterized by measuring the output characteristic depending on angle. As a result the offset voltage of the accelerometer is 43.2 mV and its sensitivity is $42.5{\mu}V/V/g$. The temperature bias drift is measured. The shock durability of the sensor is 1500g and the measuring range is 0 ~ 60 g.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.35 no.6
• /
• pp.527-534
• /
• 2017

The purpose of this study is to develop unmanned equipment that can automatically move to the desired point and measure water quality at the correct depth. For this purpose, we constructed a water sampling lift and water sampling container, an unmanned vessel equipped with a VRS-GPS, an acoustic echo sounder, and a water quality sensor. Also, we developed an automatic navigation algorithm and program, an automatic water sampling program, and a water quality map generation program. As a result of the experiment in the detention pond, the unmanned vessel sailed along the planned route with an accuracy of about 93% within the error range of 3m. In addition, the water quality sensor installed in the lift was able to acquire the water quality of the target area in real time and transmit it to the server via wireless Internet, and it was possible to monitor the water quality of each site in real time. Through field experiments, the water sampling lift was able to control the desired length with an accuracy of about 94%. The stretch length accuracy experiment of the water sampling lift was impossible to measure directly in the water, so it was replaced land-based experiment. We also found some unstable problems due to the weight of the water sampling lift and the weight of the air compressor to operate the water container. Except these two problems, we accomplished purpose of this study. An automated water quality measurement method using an unmanned vessel can be used to measure the quality of water in a difficult to access area and to secure the safety of the worker.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.16 no.3
• /
• pp.155-161
• /
• 1996

For the condition monitoring of the journal bearing in rotating machinery, a system for their diagnosis by acoustic emission(AE) was developed. AE has been used to detect abnormal conditions in the bearing system. It was found from the field application study as well as the laboratory experiment using a simulated journal bearing system that AE RMS voltage was the most efficient parameter for the purpose of current study. Based on the above results, algorithms and judgement criteria for the diagnosis system was established. The system is composed of four parts as follows: the sensing part including AE sensor and preamplifier, the signal processing part for RMS-to-DC conversion to measure AE ms voltage, the interface part for transferring RMS voltage data into PC using A/D converter, and the software part including the graphic display of bearing conditions and the diagnosis program.

• Journal of Sensor Science and Technology
• /
• v.28 no.5
• /
• pp.299-304
• /
• 2019

Recently, the development of rehabilitation medical technology has resulted in an increased interest in speech therapy equipment. In particular, research on articulation therapy for communication disorders is being actively conducted. Existing methods for the diagnosis and treatment of speech disorders have many limitations, such as traditional tactile perception tests and methods based on empirical judgment of speech therapists. Moreover, the position and tension of the tongue are key factors of speech disorders with regards to articulation. This is a very important factor in the distinction of Korean characters such as lax, fortis, and aspirated consonants. In this study, we proposed a Korean electropalatography (EPG) system to easily measure and monitor the position and tension of the tongue in articulation treatment and diagnosis. In the proposed EPG system, a sensor was fabricated using an AgCl electrode and biocompatible silicon. Furthermore, the measured signal was analyzed by implementing the bio-signal processing module and monitoring program. In particular, the bio-signal was measured by inserting it into the palatal from an experimental control group. As a result, it was confirmed that it could be applied to clinical treatment in speech therapy.

• Korean Journal of Remote Sensing
• /
• v.37 no.1
• /
• pp.169-176
• /
• 2021

The Global Space-based Inter-Calibration System (GSICS) is an international partnership sponsored by World Meteorological Organization (WMO) to continue and improve climate monitoring and to ensure consistent accuracy between observation data from meteorological satellites operating around the world. The objective for GSICS is to inter-calibration from pairs of satellites observations, which includes direct comparison of collocated Geostationary Earth Orbit (GEO)-Low Earth Orbit (LEO) observations. One of the GSICS inter-calibration methods, the Ray-matching technique, is a surrogate approach that uses matched, co-angled and co-located pixels to transfer the calibration from a well calibrated satellite sensor to another sensor. In Korea, the first GEO satellite, Communication Ocean and Meteorological Satellite (COMS), is used to participate in the GSICS program. The National Meteorological Satellite Center (NMSC), which operated COMS/MI, calculated the Radiative Transfer Model (RTM)-based GSICS coefficient coefficients. The L1P reproduced through GSICS correction coefficient showed lower RMSE and Bias than L1B without GSICS correction coefficient applied. The calculation cycles of the GSICS correction coefficients for COMS/MI visible channel are provided annual and diurnal (2, 5, 10, 14-day), but long-term evaluation according to these cycles was not performed. The purpose of this paper is to perform evaluation depending on the annual/diurnal cycles of COMS/MI GSICS correction coefficients based on the ray-matching technique using Suomi-NPP/Visible Infrared Imaging Radiometer Suite (VIIRS) data as reference data. As a result of evaluation, the diurnal cycle had a higher coincidence rate with the reference data than the annual cycle, and the 14-day diurnal cycle was the most suitable for use as the GSICS correction coefficient.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.182-184
• /
• 2012

마이크로소프트에서 개발한 키넥트(kinect)는 엑스박스(XBox) 게임 컨트롤러로 사용하는 장비이며 이 센서를 이용하여 사용자의 인체 행동을 인식하여 게임을 진행할 수 있는 센서 시스템이다. 또한 윈도우 환경에서 키넥트를 활용하여 다양한 응용 프로그램 개발을 할 수 있도록 SDK를 제공하고 있다. 현대사회에서 각종 범죄가 늘어남에 따라서 CCTV의 운용이 늘어나고 있으며 지정된 구역을 감시하는데 다양한 영상 장비들과 프로그램이 운용하고 있다. 시장에 판매되고 있는 CCTV 장비들 중에서 사람 추적기능을 가능 제품은 가격이 대부분 고가이다. 또한 야간에서는 사람의 감지가 힘들다. 본 연구에서는 키넥트의 골격 추적기능과 음성인식 기능을 활용하여 실시간 영상 녹화 프로그램을 개발하고자 하며, 개발된 프로그램은 키넥트 센서로 영상을 실시간 녹화하고 침입자에 대한 움직임을 자동 추적하여 녹화하는 DVR 시스템을 제안하고자 한다. 또한 야간에서는 깊이(Depth) 영상을 이용하여 인물을 인식과 추적을 한다. 궁극적으로 키넥트 센서(Kinect Sensor)의 CCTV기능에 대한 활용성을 연구하는데 목적을 가진다.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.8 no.1
• /
• pp.12-21
• /
• 1988

The behaviour of pressure vessel made of SS41 steel was investigated during hydrotest. AE tests were carried out for the vessels in as-manufactured, V-notched and weld-cracked state using microcomputer-based AE instrumentation. The following results were obtained: 1) In the case of source location using cylindrical program, to minimize the error of source location, the difference of max. Delta T values measured from each sensor should be kept as small as possible. 2) When crack grew, AE event rate increased continuously but AE event from the inclusions occurred intermittently, so by analyzing event rate, the source of AE could be derived. 3) From the spot welding part of supporter, many events with low energy occurred independent of Kaiser effect, which could be confirmed by analyzing energy parameter. 4) The b-value from the tensile specimen of was lower than that from normal specimen and the b-value from crack propagation was lower than that from deformation, so by analyzing peak amplitude distribution, the source mechanism could be derived from the b-value.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.7
• /
• pp.583-589
• /
• 2008

For the purpose of monitoring by ultrasonic test of the ball bearing conditions in rotating machinery, a system for their diagnosis was developed. ultrasonic technique is used to detect abnormal conditions in the bearing system. And various data such as frequency spectrum, energy and amplitude of ultrasonic signals, and ultrasonic parameters were acquired during experiments with the simulated ball bearing system. Based on the above results and practical application for power plant, algorithms and judgement criteria for diagnosis system was established. Bearing diagnosis system is composed of four parts as follows : sensing part for ultrasonic sensor and preamplifier, signal processing part for measuring frequency spectrum, energy and amplitude, interface part for connecting ultrasonic signal to PC using A/D converter, graphic display and software part for display of bearing condition and for managing of diagnosis program.

• Journal of Bio-Environment Control
• /
• v.5 no.2
• /
• pp.210-214
• /
• 1996

The measuring system was developed for automation of hydroponic culture. It runs in Windows 3.1 and 95. Main window contains greenhouse screen and menu bars such as system setting, sensor calibration, greenhouse status, actuator control, file management, view, and help. Users can use pop-up menu, tool bar and status bat as well as menu bar for manipulation. Especially it was designed to retain flexibility for researchers, who changed detecting sensors frequently. Users can change storage intervals of files, of which 3 types were prepared to use in other software like as statistical programs, graphic programs and/or spread sheets. This system was adopted to deep flow culture system and evaluated to be appropriate for any kind of hydroponic systems.