• Steel and Composite Structures
• /
• 제26권1호
• /
• pp.67-78
• /
• 2018

The application of rib stiffeners is common on steel connections, with regard to the stiffened angle connection, experimental results about the influence of stiffeners under monotonic and cyclic loading are very limited. Consequently, this paper presents the experimental investigation on four types angle connections with or without stiffener under static loading and another four type stiffened angle connections subjected to cyclic loading. The static experimental result showed that the rib stiffener weld in tension zone of the connection greatly enhanced its initial rotational stiffness and flexural strength. While a stiffener was applied to the compression zone of the connection, it had not obvious influences on the initial rotational stiffness, but increased its flexural strength. The moment-rotation curves, skeleton curves, ductility, energy dissipation and rigidity were evaluated under cyclic loading. Stiffened top-and-seat angle connections behaved as semi-rigid and partial strength, and rotation of all stiffened angle connections exceeded 0.04rad. The failure modes between monotonic and cyclic loading test were completely different and indicated certain robustness.

• 한국전산구조공학회논문집
• /
• 제14권4호
• /
• pp.537-549
• /
• 2001

본 논문은 강 뼈대 구조물의 보-기둥 접합부의 사실적인 상태를 묘사하기 위하여 부분구속 접합부(Partially Restrained (PR) connections)를 고려한 지진하중 상태하의 신뢰성 해석과 접합부 및 그들에 내재된 불확실성이 구조물의 위험도에 미치는 영향에 관한 연구이다. 신뢰성해석을 위하여 응답면기법(Response Surface Method), 유한요소법(Finite Element Method), 일차신뢰도법(First Order Reliability Method), 그리고 반복선형보간 기법(Iterative Linear Interpolation Scheme)을 효과적으로 결합한 추계유한요소법(Stochastic Finite Element Method)을 제안하였다 일반적으로 모멘트-상대회전각 곡선에 의해서 표현되는 보-기둥에 대한 부분구속 접합부(PR connections)의 거동이 본 논문에서는 네 개의 매개변수를 사용하는 리차드 모델(Four-parameter Richard Model)을 사용하여 모사하였다. 지진하중에 대하여, 부분구속 접합부에서의 재하(Loading), 제하(Unloading) 및 재재하(Reloading) 거동은 모멘트-상대회전각 곡선과 Masing법칙을 사용하여 표현하였다. 시간영역에서 지진가속도를 구조물에 작용시킴으로써 지진하중의 사실적인 재현을 도모하였다. 다양한 주요 비선형성의 원인들을 고려한 부분구속 접합부를 가지는 강 뼈대 구조물의 신뢰성해석이 지진위험도를 평가하기 위하여 수행되었다. 제안된 기법의 명확한 이해를 돕기 위하여 한 예제를 제시하였다.

• Steel and Composite Structures
• /
• 제26권3호
• /
• pp.315-328
• /
• 2018

Built-up Double-I (BD-I) columns consist of two hot rolled IPE sections and two cover plates which are welded by fillet welds. In Iran, this type of column is commonly used in braced frames with simple connections and sometimes in low-rise Moment Resisting Frames (MRF) with Welded Flange Plate (WFP) beam-column detailing. To evaluate the seismic performance of WFP connection of I-beam to BD-I column, traditional and modified exterior MRF connections were tested subjected to cyclic prescribed loading of AISC. Test results indicate that the traditional connection does not achieve the intended behavior while the modified connection can moderately meet the requirements of MRF connection. The numerical models of the connections were developed in ABAQUS finite element software and validated with the test results. For this purpose, moment-rotation curves and failure modes of the tested connections were compared with the simulation results. Moreover to avoid improper failure modes, some improvements of the connections were evaluated through a numerical study.

• Steel and Composite Structures
• /
• 제41권5호
• /
• pp.747-759
• /
• 2021

Built-up Double-I (BD-I) columns have been commonly used for mid-rise steel-frame structures in Iran. These columns consist of two hot rolled IPE sections which are connected by two cover plates and fillet welds. Until 2017, BD-I columns were employed in intermediate moment resisting frames (MRF) using welded flange plate (WFP) connections. To evaluate the seismic behavior of the connections, four samples were made and tested based on cyclic loading according to AISC 341-16. It was concluded that typical samples cannot satisfy the seismic provisions related to intermediate MRFs. In contrast, the proposed connections retrofitted with two-part external diaphragms were able to satisfy not only the seismic requirements related to intermediate MRFs but also those related to special MRFs according to AISC. The numerical modeling of these samples was performed using ABAQUS finite element software. This study compared the hysteresis moment-rotation curves, plastic strains, and behavior modes in both experimental samples and numerical models.

• Geomechanics and Engineering
• /
• 제7권6호
• /
• pp.679-703
• /
• 2014

This paper investigates nonlinear response of 51 laterally loaded rigid piles in sand. Measured response of each pile test was used to deduce input parameters of modulus of subgrade reaction and the gradient of the linear limiting force profile using elastic-plastic solutions. Normalised load - displacement and/or moment - rotation curves and in some cases bending moment and displacement distributions with depth are provided for all the pile tests, to show the effect of load eccentricity on the nonlinear pile response and pile capacity. The values of modulus of subgrade reaction and the gradient of the linear limiting force profile may be used in the design of laterally loaded rigid piles in sand.

• Computers and Concrete
• /
• 제14권3호
• /
• pp.279-297
• /
• 2014

This paper investigates the effects of confinement reinforcement and concrete strength on nonlinear behaviour of reinforced concrete buildings (RC). For numerical application, an eleven-storey and four bays reinforced concrete frame building is selected. Nonlinear incremental static (pushover) analyses of the building are performed according to various concrete strengths and whether appropriate confinement reinforcement, which defined in Turkish seismic code, exists or not at structural elements. In nonlinear analysis, distributed plastic hinge model is used. As a result of analyses, capacity curves of the frame building and moment-rotation curves at lower end sections of ground floor columns are determined. These results are compared with each other according to concrete strength and whether appropriate confinement reinforcement exists or not, respectively. According to results, it is seen that confinement reinforcement is important factor for increasing of building capacity and decreasing of rotations at structural elements.

• 국제강구조저널
• /
• 제18권5호
• /
• pp.1684-1698
• /
• 2018

Fragility functions are determined for braced steel moment frames (SMFs) with plans such as square-, T-, L-, U-, trapezoidal-, and semicircular-shaped, subjected to blast. The frames are designed for gravity and seismic loads, but not necessarily for the blast loads. The blast load is computed for a wide range of scenarios involving different parameters, viz. charge weight, standoff distance, and blast location relative to plan of the structure followed by nonlinear dynamic analysis of the frames. The members failing in rotation lead to partial collapse due to plastic mechanism formation. The probabilities of partial collapse of the SMFs, with and without bracing system, due to the blast loading are computed to plot fragility curves. The charge weight and standoff distance are taken as Gaussian random input variables. The extent of propagation of the uncertainties in the input parameters onto the response quantities and fragility of the SMFs is assessed by computing Sobol sensitivity indices. The probabilistic analysis is conducted using Monte Carlo simulations. The frames have least failure probability for blasts occurring in front of their corners or convex face. Further, the unbraced frames are observed to have higher fragility as compared to counterpart braced frames for far-off detonations.

• 한국지진공학회논문집
• /
• 제3권4호
• /
• pp.23-32
• /
• 1999

본 연구에서는 반복하중을 받는 H형강보 접합부의 거동을 실험적인 방법으로 조사하였다. 본 연구의 목적은 H형강보 접합부의 이력거동에 강제의 특성과 스캘럽의 형태가 주는 영향을 조사하는 것이다 5개의 접합부 시험체를 제작하여 반복하중을 재하면서 실험을 수행하였다. 보 접합부에서의 하중-회전변형 곡선을 얻었으며 접합부의 변형능력과 에너지 소산능력을 상호 비교하였다. 강재가 SS400인 시험제는 충분한 변형능력과 에너지소산능력을 보였으나 강재가 SM490인 시험체는 취성적인 파괴를 보였으며 변형능력이 작았다. 접합부 스캘럽의 형태는 접합부의 거동에 영향을 주지않았다.

• Steel and Composite Structures
• /
• 제36권4호
• /
• pp.427-446
• /
• 2020

This paper carries out the progressive collapse analysis of stainless steel composite beam-to-column joint sub-models and moment-resisting frames under column removal scenarios. The static flexural response of composite joint sub-models with damaged columns was initially explored via finite element methods, which was validated by independent experimental results and discussed in terms of moment-rotation relationships, plastic hinge behaviour and catenary actions. Simplified finite element methods were then proposed and applied to the frame analysis which aimed to elaborate the progressive collapse response at the frame level. Nonlinear static and dynamic analysis were employed to evaluate the dynamic increase factor (DIF) for stainless steel composite frames. The results suggest that the catenary action effect plays an important role in preventing the damaged structure from dramatic collapse. The beam-to-column joints could be critical components that influence the capacity of composite frames and dominate the determination of dynamic increase factor. The current design guidance is non-conservative to provide proper DIF for stainless steel composite frames, and thus new DIF curves are expected to be proposed.

• 한국강구조학회 논문집
• /
• 제23권3호
• /
• pp.357-365
• /
• 2011

저층 장스팬 철골프레임에는 강재절감을 위해 휨모멘트 저항을 극대화 한 판폭두께비가 큰 변단면 부재를 이용한 PEB시스템을 사용하고 있다. 과다한 외력에 의해 PEB시스템의 붕괴에 대한 안정성을 파악하기 위해서는 변단면 부재의 좌굴거동에 관한 실험 및 해석적 예측은 중요하다. 이에 본 연구에서는 변단면의 판폭(춤)두께비(d/t)와 변단면비를 주요 변수로 한 변단면 부재에 대한 실대형 실험을 행하였다. 현행 설계기준, 수정된 Yoda 모델을 이용한 소성힌지해석 및 유한요소해석으로 예측한 초기강성, 내력 및 모멘트-회전각관계에 대해서 실험결과와 비교하였다.