• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.780-782
• /
• 2001

The mold transformer has anti-burnt and possibility of small size contrary to oil-immersed transformer. The mold transformer has generally cooling duct between low voltage coil and high voltage coil and also made by one body molding for small size and low loss. In this paper, the temperature distribution of designed 50kVA pole mold transformer for power distribution is investigated by FEM program. The designed transformer is also manufactured and temperature rise test is carried out.

• 산업경영시스템학회지
• /
• 제35권2호
• /
• pp.196-203
• /
• 2012

When manufacturing die casting mold, generally, the casting layout design should be considered based on the relation between injection system, casting condition, gate system, and cooling system. Also, the extent or the location of product defects were differentiated according to the various relations of the above conditions. High-qualified products can be manufactured as those defects are controled by the proper modifications or the changes of die casting mold with the conditions. In this research, the proper manufacturing method was derived intensively for reducing the defect of the internal porosity of steering wheel housing which is very complicated to achieve a good mold design. The method was also derived for minimizing and for guaranteeing the product quality through the analysis of the casting problem and the deduction of alternative plans.

• 한국주조공학회지
• /
• 제36권5호
• /
• pp.153-158
• /
• 2016

The lost foam casting process was used to fabricate Al-Si-Mg cast specimens, and the effects of the chemical composition and process variables on the tensile properties and the mold filling ability were investigated. Some porosity formation was observed in thick sections of the casting and better tensile properties were obtained for thin sections, presumably because of their lower porosity and the higher cooling rate. Tensile properties were not clearly enhanced by grain refining treatment with Ti; however, the elongation was significantly improved by Sr modification of the Al-Si-Mg alloy. The mold filling distance was generally proportional to the pouring temperature of the melt, and the distance was also increased by the addition of Ti.

• 한국주조공학회지
• /
• 제22권2호
• /
• pp.82-88
• /
• 2002

Al-5.5Zn-2.5Mg-l.5Cu semi-solid slurry was prepared by cooling the liquid metal with a low superheat to a solid and liquid co-existing temperature. Relatively round solid particles could be obtained in the slurry through the simple process. The prepared slurry was deformed into the metallic mold by a press and the mechanical properties of obtained specimens were investigated. Mold filling ability of the alloy slurry was also investigated and compared with that of A356 alloy. Al-Zn-Mg-Cu alloy showed lower mold filling ability than A356 alloy probably because small amount of eutectic phase is present and the heat of fusion generated during solidification is smaller than that of A356 alloy.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 추계학술대회 논문집
• /
• pp.193-194
• /
• 2006

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2000년도 하계학술대회 논문집 C
• /
• pp.1900-1902
• /
• 2000

In this paper, the temperature distribution and thermal stress analysis of mold transformer for power distribution system is investigated by FEM. Filler type epoxy is applied for good cooling effect in mold transformer.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.811-814
• /
• 2001

Warpage analysis of bobbin, molded by injection molding process was performed. Concerned with a mold design, cooling system was designed based on Taguchi method, the distance between cavity wall and cooling channel was most influent factor amongst four design variables like an inlet temperature of coolant, a coolant flow rate, a diameter of cooling channel, and the distance between cavity wall and cooling channel. Optimal packing processes to reduce the warpage of molded part was analyzed based on the response surface method by considering holding pressure. Their optimal processing conditions were 9.4 seconds, 5.3 seconds, 15.2 seconds, and 85MPa, respectively.

• Design & Manufacturing
• /
• 제13권2호
• /
• pp.1-5
• /
• 2019

In this study, micro cellular injection molding of automobile head lamp housing with uneven thickness structure was performed to obtain improvement on deformation and light-weight of the part. The thickness of the presented model was uniformly modified to control the deformation of the molded part. In order to maximize the lightweight ratio, the model having an average thickness of 2.0 mm were thinly molded to an average thickness of 1.6 mm. GFM(Gas Free Molding) and CBM(Core Back Molding) technology were applied to improve the problems of the conventional foam molding method. Equal Heat & Cool system was also applied by 3D cooling core and individual flow control system. Warpage of the molded parts with even cooling was minimized. To improve the mechanical properties of foamed products, complex resin containing nano-filler was used and variation of mechanical properties was evaluated. It was shown that the weight reduction ratio of products with light-weighted injection molding was 8.9 % and the deformation of the products was improved from the maximum of 3.6 mm to 2.0 mm by applying Equal Heat & Cool mold cooling system. Also the mechanical strength reduction of foamed product was less than 12% at maximum.

• 한국산학기술학회논문지
• /
• 제16권8호
• /
• pp.5074-5081
• /
• 2015

플라스틱 제품의 휨을 개선하기 위한 방법은 사출성형 공정에서 일어나는 불균일한 냉각을 균일하게 만들어 플라스틱 제품의 잔류응력을 제거하는 방법이다. 본 연구는 균일한 냉각을 위하여 펠티에 소자를 사용하여 급속가열 냉각 장치를 개발하였다. 급속냉각 가열 장치(RCHD)를 제작하여 전통적인 수냉 장치(TWCD)방식과 급속냉각 가열 장치방식에 따른 휨을 비교 분석하였고, 비결정성 수지인 ABS 수지를 사용하였다. 사출성형 조건인 보압시간, 금형온도, 냉각시간, 보압에 따라 휨의 변화량을 측정 비교하였고, 비결정성 ABS 수지에서 급속가열 냉각 장치 냉각방식이 전통적인 수냉방식 보다 휨이 더 적게 발생하고, 위의 결과들로 보아 조금 더 균일하게 냉각되는 것을 알 수 있었다. ABS 폴리머의 분포 상태를 SEM 사진을 통해서 확인하였다. 전통적인 수냉방식은 폴리머의 분포상태가 조밀하게 분포되어 있고, 급속냉각 가열 방식은 전통적인 수냉방식 보다 넓게 분포되어 있었다. 이것은 냉각이 균일하게 이루어지고, 금형의 온도가 서서히 진행되면서 폴리머의 입자가 커지게 되는데, 이것은 내부응력이 줄어든 것을 의미한다.

• Design & Manufacturing
• /
• 제13권2호
• /
• pp.17-21
• /
• 2019

In this study, selective laser sintered 3D printing mold core and metal core were used to investigate the difference of the thickness shrinkage from the gate of the injection molded part at a constant interval. SLS 3D printing mold core was made of nylon-based PA2200 powder and the metal core was manufactured by conventional machining method. As the PA2200 powder material has low strength, thermal conductivity and high specific heat characteristics compared with metal, molding conditions were set with the consideration of molten temperature and injection pressure. Crystalline resin(PP) and amorphous resin(PS) with low melting temperature and viscosity were selected for the injection molding experiment. Cooling time for processing condition was selected by checking the temperature change of the cores with a cavity temperature sensor. The cooling time of the 3D printing core was required a longer time than that of the metal core. The thickness shrinkage of the molded part compared to the core depth was measured from the gate by a constant interval. It was shown that the thickness shrinkage of the 3D printing core was 2.02 ~ 4.34% larger than that of metal core. In additions, in the case of metal core, thickness shrinkage was increased with distance from the gate, on the contrary, in the case of polymer core showed reversed aspect.