• 상하수도학회지
• /
• 제21권6호
• /
• pp.745-753
• /
• 2007

By struvite and hydroxyapatite crystallization, was high concentration of nitrogen and phosphorus in wastewater simultaneously. Particularly, removal of nitrogen and phosphate for crystallization have been applied to landfill leachates and animal wastewater. The purpose of this study is to decide the optimum struvite crystallization factors, sequence of $Mg^{2+}$ addition, pH control and the molar ratio of $Mg^{2+}$ over $PO_4^{3-}$. In conclusion, dosage of the magnesium followed by pH control formed magnesium hydroxide, so pH was decreased. Therefore, pH adjustment should followed by after magnesium dosage and then pH should be adjusted to 11. Over pH 10, it was not good for struvite crystallization efficiency by side reaction. Following of the $Mg^{2+}$ and the $PO_4^{3-}$ are dosed excessively, the removal efficiency of the $NH_4^+$ increased. A molar ratio of $Mg^{2+}:NH_4^+:PO_4^{3-}$, 1.3:1:1.3 was the most on effective for $NH_4^+$ removal at pH 9.5. But for the perfect removal $NH_4^+$, it is thought to be that molar ratio should be 2:1:2.

• 한국환경과학회지
• /
• 제22권11호
• /
• pp.1481-1498
• /
• 2013

The SCR (selective catalytic reduction) system is highly-effective technique for NOx reduction from exhaust gases. In this study, the effects of the direction and size of nozzle and the ammonia injection concentration on the performance of SCR system are analyzed by using the computational fluid dynamics method. When the nozzle is arranged in zigzaged direction which is normal to exhausted gas flow, it is shown that the uniformity of gas flow and the NH3/NO molar ratio is improved remarkably. With the change of the ammonia injection concentration from 0.2 vol%(wet) to 1.0 vol%(wet), the uniformity of gas flow shows a good results. As the size of nozzle diameter changes from 6 mm to 12 mm, the uniformity of gas flow is maintained well. It is shown that the uniformity of the $NH_3/NO$ molar ratio becomes better with decreasing the ammonia injection concentration and the size of nozzle diameter.

• 태양에너지
• /
• 제19권2호
• /
• pp.57-65
• /
• 1999

[ $H_2O$ ]-NaCl혼합물을 냉축열재로 선택하였으며, 이 혼합물의 상변화온도를 몰농도 변화에 의하여 조절하였다. 그리고 고농도와 저농도의 NaCl과 $H_2O$가 ion-dipole interaction으로 결합하는 구조를 그림으로 가시화하고 가열, 냉각과정에서 $H_2O$-NaCl이 동결, 융해하는 현상을 도시하므로서 융해와 동결과정에서 상변화온도가 2단계로 나타나는 구조적 원인을 구명하였으며, NaCl의 농도변화에 따른 상변화온도를 이론적으로 분석하므로서 실험 및 이론분석 결과의 타당성을 증명할 수 있도록 하였다.

• Bulletin of the Korean Chemical Society
• /
• 제33권6호
• /
• pp.1962-1966
• /
• 2012

Boehmite sols have been prepared by crystallization of amorphous aluminum hydroxide gel obtained by hydrolysis and peptization of aluminum using acetic acid. The size of the boehmite crystallites could be controlled by Al molar concentration in amorphous gel by means of controlling grain growth at nucleation stage. The size of boehmite increases as a function of Al molar concentration. With increasing boehmite crystallite size, the $d_{(020)}$ spacing and the specific surface area decreases, whereas the pore volume increases along with pore size. Especially, the pore size of the boehmite sol particles is comparable to the crystallite size along the b axis, suggesting that the fibril thickness along the b axis among the crystallite dimensions of the boehmite contributes to the pore size. Therefore, the physical properties of boehmite sols can be determined by the crystallite size controlled as a function of initial Al concentration.

• Journal of Dental Anesthesia and Pain Medicine
• /
• 제15권3호
• /
• pp.121-128
• /
• 2015

Background: The authors studied the hemodynamic effect influent by using the novel high concentration of lidocaine HCl for surgical removal impacted lower third molar. The objective of this study was to evaluate the hemodynamic change when using different concentrations of lidocaine in impacted lower third molar surgery. Methods: Split mouth single blind study comprising 31 healthy patients with a mean age of 23 years (range 19-33 years). Subjects had symmetrically impacted lower third molars as observed on panoramic radiograph. Each participant required 2 surgical interventions by the same surgeon with a 3-week washout period washout period. The participants were alternately assigned one of two types of local anesthetic (left or right) for the first surgery, then the other type of anesthetic for the second surgery. One solution was 4% lidocaine with 1:100,000 epinephrine and the other was 2% lidocaine with 1:100,000 epinephrine. A standard IANB with 1.8 ml volume was used. Any requirement for additional anesthetic and patient pain intra-operation was recorded. Post-operatively, patient was instructed to fill in the patient report form for any adverse effect and local anesthetic preference in terms of intra-operative pain. This form was collected at the seven day follow up appointment. Results: In the 4% lidocaine group, the heart rate increased during the first minute post-injection (P < 0.05). However, there was no significant change in arterial blood pressure during the operation. In the 2% lidocaine group, there was a significant increase in arterial blood pressure and heart rate in the first minute following injection for every procedure. When the hemodynamic changes in each group were compared, the 4% lidocaine group had significantly lower arterial blood pressure compared to the 2% lidocaine group following injection. Post-operatively, no adverse effects were observed by the operator and patient in either local anesthetic group. Patients reported less pain intra-operation in the 4% lidocaine group compared with the 2% lidocaine group (P < .05). Conclusions: Our results suggest that a 4% concentration of lidocaine HCl with 1:100,000 epinephrine has better clinical efficacy than 2% lidocaine HCl with 1:100,000 epinephrine when used for surgical extraction of lower third molars. Neither drug had any clinical adverse effects.

• Journal of Periodontal and Implant Science
• /
• 제32권3호
• /
• pp.501-521
• /
• 2002

The purpose of this study is to evaluate the influences of the bone morphogenetic protein (BMP) on the healing of periodontal ligament and alveolar bone after replantation of tooth, and to examine the possibility of its clinical application. 45 Sprague Dawley rats weighted about 100 gram were divided into 3 experimental groups by different dose of BMP. All the upper right and left 1st molar were extracted after 5 days feeding of 0.4% ${\beta}$-aminopropionitrile, and right molar were used as experimental group and left molar were used as control group. The root surface of experimental molar were treated with 25,50 and l00ng/ml of human recombinant Bone morphogenetic protein-4 (rh-BMP-4) with micropipet, and 1M Sodium hypochloride were used on control root surface. All the experimental animals were sacrificed as 1, 2, 4, 7 and 14 days after autoreplantation of upper 1st molar into their own position. The maxilla were disected included both side of 1st molar. The collected tissue were processed from demineralization to paraffin embeding as usual procedure, and the specimens were prepared with Hematoxylin-Eosin stain for the light microscopic evaluation. The results of this study were as follows : 1. There was no significant differences between control and experimental site on 1 and 2 days after replantation of tooth. In the case of 4th days, the evidence of tissue regeneration were observed on experimental site to compare the controls. New osteoid were revealed on high concentration of BMP at 7 days after replantation, and it became more obvious at 14 days, 2. The effect of the rh-BMP-4 coated on root surface was revealed slight influences for the prolifertion of cells of periodontium and tissue regeneration as dose-dependent pattern. 3. Bony ankylosis was observed between alveolar bone and root surface due to the remarkable amount of osteoid formation on the 14 days after replantation of root. In the conclusion, it was suggested that topical application of the rhBMP-4 on the root surface has influence on the periodontal ligament and alveolar bone. The application method of BMP on the root should be designed with calculation of proper concentration.

• 한국재료학회지
• /
• 제9권9호
• /
• pp.878-882
• /
• 1999

분자선증착법으로 (0001) 사파이어 기판 위에 $Al_xGa_1-_xN$ 에피층을 AlN 몰비를 변화시키면서 성장시켰다. AlN 몰비는 0.16에서 0.76까지 변화시켰으며 X선의 회절 실험과 Rutherford backscattering spectroscopy 방법을 이용하여 AlN 몰비를 결정하였다. $Al_xGa_1-_xN$ 에피층의 깊이 방향의 조성 변화를 관찰하였으며 스퍼터 시간에 대해 각 원소가 일정한 원자 농도를 가짐을 알 수 있었다. AlN 몰비의 증가에 따른 표면 특성의 변화를 관찰하기 위하여 atomic force microscopy 측정을 수행하였다. 표면에서의 입자 모양이 AlN 몰비가 변화함에 따라 원형에서 침상형태로 변화함을 알 수 있었다. 표면 입자에 대한 root mean square 값과 average roughness 값을 구하였으며 AlN 몰비를 바꿈에 따라 나타나는 변화를 관찰하였다.

• Asian-Australasian Journal of Animal Sciences
• /
• 제13권7호
• /
• pp.922-928
• /
• 2000

The effects of animal species and supplements on rumen fluid characteristics, plasma urea-N (PUN) concentration, plasma urea-N pool size, urea-N degradation in the gut and urea-N net flux (urea-N synthesis rate) were studied in goats and sheep, with some minor differences detected. The animals were fed either chopped rice straw ad libitum+200 g soybean meal (SBM), or chopped rice straw ad libitum+190 g soybean meal+300 g sago meal (SBM+SM) for 14 days. The supplements were isonitrogenous (80 g crude protein/animal/d). [$^{14}C$]-urea was used as the marker for urea metabolism studies. Two animals from each species were fed either supplement in a cross-over design in two periods. The results showed that rumen pH was significantly (p<0.001) lower in animals fed SBM+SM than those fed SBM supplement. The ammonia concentrations of rumen fluid were significantly (p<0.01) higher in sheep (382.9 mg N/L) than goats (363.1 mg N/L) when fed SBM supplement but lower (282.5 mg N/L) than that of goats (311.0 mg N/L) when fed SBM+SM supplement. Total VFA concentrations were significantly (p<0.05) higher in animals fed SBM+SM supplement than those fed SBM supplement. Goats had significantly (p<0.01) higher molar proportions of acetate (79.1, 77.7%, respectively) than sheep (75.8, 74.0%, respectively) in both supplements. The molar proportion of acetate was significantly (p<0.05) higher, while that of butyrate lower in animals fed SBM supplement than those fed SBM+SM supplement. In animals fed SBM supplement, the molar proportion of propionate was significantly (p<0.01) higher in sheep (18.0%) than in goats (15.6%), but in animals fed SBM+SM, the molar proportion of butyrate was significantly (p<0.01) higher (9.6%) in sheep than in goats (7.2%). Plasma urea-N concentration, plasma urea-N pool size, urea-N degradation in the gut, urea-N net flux and the fraction of urea-C from the blood entering the rumen were not significantly different between goats and sheep fed either supplement. However, PUN concentration was significantly (p<0.05) lower in animals fed SBM+SM supplement (average of 13.8 mg N/100 ml) than in those fed SBM supplement (average of 16.5 mg N/100 ml). The urea net flux was significantly (p<0.05) higher in goats (average of 14.5 g N/d) than sheep (average of 12.9 g N/d), and animals fed SBM supplement showed higher (average of 14.9 g N/d) urea net flux than animals fed SBM+SM supplement (average of 12.9 g N/d). A significant (p<0.05) positive correlation was observed between urea-N net flux and urea-N degradation; urea-N net flux and pool size; urea-N net flux and urea excretion in the urine; and PUN and rumen ammonia in goats. While in sheep, significant (p<0.05) positive correlation was observed between urea-N net flux and urea excretion in the urine; and PUN and rumen ammonia.

• 대한자기공명의과학회:학술대회논문집
• /
• 대한자기공명의과학회 2006년도 제11차 학술대회
• /
• pp.36-36
• /
• 2006

• 구강회복응용과학지
• /
• 제17권4호
• /
• pp.245-256
• /
• 2001

The purpose of this study is to analyze the mechanical stress and displacement on the jaws during the simulated bilateral clenching task on the three-dimensional finite element model of the dentated skull with unilateral molar loss. For this study, the computed tomography(G.E.8800 Quick, USA) was used to scan the total length of human skull in the frontal plane at 2.0mm intervals. The fully assembled finite element model consists of the articular disc, maxilla, mandible, teeth, periodontal ligament and cranium. The FE model was used to simulate the bilateral clenching in intercuspal position. The loading condition was the force of the masseter muscle exerted on the mandible as reported by Korioth et al. degrees of freedom of the zygomatic region where the masseter muscle is attached were fixed as restraints. In order to reflect the actual action of the muscles force, the displacement of the region was attached where the muscle is connected to the temporal bone and restraint conditions were given values identical to values at the attachment region of the masticatory muscle but with the opposite direction of the reaction from when the muscle force is acted on the mandible. Although the mandible generally has higher displacement and von Mises stress than the maxilla, its mandibular corpus on the molar-loss side has a higher stress and displacement than the molar-presence side. Because the displacement and von Mises Stress was the highest on the lateral surface of mandibular corpus with molar loss, the stress level of the condyle on the molar-loss side is greater than that of the molar-presence side, which in turn caused the symphysis of the mandible to bend. In conclusion, the unilateral posterior bite collapse with molar loss under para-functional activities such as bruxism and clenching can affect the stress concentration on the condyle and mandibular corpus. It is therefore necessary to consider the biomechanical function of dento-skeleton under masticatory force while designing the occlusal scheme of restoration on alveolar bone with the posterior collapse.