• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.235-246
• /
• 1994

At pre-construction design stage, most of the design data are based on the site investigation results or property estimation which often does not provide satisfactory output for the tunnel analysis. Nonlinear FEM tunnel analysis was cariied out by Hoek-Brown model which is principly semi-empirical design method based on insitu rock descriptions, rock test results as well as field measurement data. The results of the analytical methods from Hoek-Brown model and Mohr-Coulomb model are compared with the sige measurement data from two-NATM tunnel construction sites. It was found that the Hoek-Brown model can be satisfactorily adopted as a feed back analysis technique in order to examin the safety of NATM tunnel at any construction stage.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.231-234
• /
• 1994

Concentrated stresses due to the tunnel excavation easily cause failure around opening in the soft rock mass layer. Thus, while excavatng tunnel in the soft rock mass layerm it is very important to predict the possibility of failure or yielding zones around tunnel boundary. There are two typical methods to predict these; 1) the analysis of field monioring data and 2) numerical analysis. In this study, it was attempted to describe the time-dependent or progressive rock mass manner due to the continuous failure and fracturing caused by surrounding underground openings using the second method. In order to apply the effects of progressive failure underground, an iterative technique was used with the Hoek and Brown rock mass failure theory. By developing and simulating, three different shapes of twin tunnels, this research simulated and estimated the proper size of critical pillar width between tunnels, distributed stresses on the tunnel sides, and convergences of tunnel crowns. Moreover, results out progressive failure technique based on the Hoek and Brown theory were compared with the results out of Mohr-Coulomb theory.

• Computers and Concrete
• /
• v.12 no.3
• /
• pp.303-318
• /
• 2013

The purpose of this study is to present different composed material models for reinforced concrete structures (RC). For this aim a nonlinear finite element analysis program is coded in MATLAB. This program contains several yield criteria and stress-strain relationships for compression and tension behavior of concrete. In this study, the well-known criteria, Drucker-Prager, von Mises, Mohr Coulomb, Tresca, and two new criteria, Hsieh-Ting-Chen and Bresler-Pister, are taken into account. It is concluded that the coded program, the new yield criteria, and the models considered can be effectively used in the nonlinear analysis of reinforced concrete beams.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1991.10a
• /
• pp.216-232
• /
• 1991

This Finite Element Program(TAFEM) has been developed to be able to carry out the structural analsis of tunnel section and simulate the surrounding ground behaviour due to New Austrian Tunnelling Method, of which main support is the surrounding ground, itself. The Elasto-plastic theory has been applied. The used finite elements are 8-noded isoparametric element(rock & shotcrete), 2 or 3-noded rod element(rock bolt) and infinite boundary element. The load incremental method and tangential stiffness method has been used. Associated flow rule was applied to plastic flow and yield criteria inclued not only Mohr-Coulomb but also Drucker-Prager. In this paper, Drucker-Prager yield criterion has been used. The relationship between plastic strain and stress is based on the incremental strain concept and stress-strain equation on the basis of the stress path of each gauss point has been adopted. It may be rational that rock is considered to be no-tension material, so that no-tension analysis has been adopted in accordance with the brittle fracture constitutive equation.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1991.10a
• /
• pp.166-178
• /
• 1991

Using FLAC, which is an explicit finite difference code written for analysis of problems in geotechnical engineering, a particular example 2 in the Korean Geothechnical Society News has been analysed. The elastoplasticity formulation in FLAC assumes an elastic, perfectly plastic solid in plane strain which conforms to a Mohr-Coulomb yield condition. During tunnel excavations by stages, stresses and diaplacements in region around the tunnel varies according to distance from the face of tunnel and installation of tunnel supports, and soon. In this analysis, the three dimensional support effect of the rock mass during the process of excavation is simulated by using the stress distribution method, and varying the material constants of shotcrete in each stage also considered. The maximum convergency is occured at the crown of the tunnel and estimated to be about 12mm.

• Geomechanics and Engineering
• /
• v.14 no.6
• /
• pp.509-517
• /
• 2018

This paper proposes a numerical methodology for capturing the complete curve of a pressuremeter test including initial or disturbed parts and loops through a stiffness-based approach adopted in three dimensional finite difference code, FLAC3D. In order to enable this, a new hyperbolic model was used to replace the conventional linear elastic model prior to peak strength of Mohr-Coulomb soil model and update or degradation of shear modulus was considered. Presented modeling approach and implemented constitutive model are impressively successful. It leads to obtain the whole set of parameters for characterizing sands and seems promising for modeling the most of geotechnical structures.

• Proceedings of the Korean Society for Rock Mechanics Conference
• /
• 2001.03a
• /
• pp.109-117
• /
• 2001

불연속체 해석을 이용하여 터널 안정성 해석을 수행할 경우 해석 결과는 절리 모델의 선택에 따라 달라진다. 따라서 본 연구에서는 개별요소법을 이용한 불연속체 터널 안정성 해석에 있어 BB 모델 적용시의 해석 결과와 MC 모델 적용시의 해석 결과를 비교하였다. 또한 주어진 응력 조건과 터널 형상에 따른 암반의 변형 거동을 규명하기 위하여 불연속체 해석 결과와 연속체 해석 결과를 비교하였다. 연속체 해석결과와 BB 모델을 사용한 불연속체 해석 결과는 변위 및 응력 분포는 비슷한 양상을 보이는 반면, MC 모델을 사용한 불연속체 해석결과는 이와 다른 양상을 보였다. 또한 MC 모델을 사용하여 불연속체 해석을 실시할 경우 절리의 영향을 명시적으로 고려하였음에도 불구하고 연속체 해석 결과에 비해 변위 및 최소 주응력이 더 작게 발생할 수 있음을 확인할 수 있었다. 이는 MC 모델이 실제 절리의 변형거동 특성을 현실적으로 모사할 수 없기 때문에 발생되는 결과이며, 특히 절리면의 전단거동에 무관하게 팽창각을 일정한 상수로 취급하는 MC 모델의 특성으로 인한 결과이다.

• Magazine of the Korea Concrete Institute
• /
• v.4 no.4
• /
• pp.135-147
• /
• 1992

본 연구는 기존의 이론을 배경으로 전단키에 영향을 미치는 전달전달의 요소가 포함된 기본식을 산정하여, 접합부의 유형에 따라 구체적으로 전단강도를 예측하는 방법을 제안하였다. 접합부 콘크리트와 횡보강철근의 강도 및 장부호과를 고려한 프리캐스트 콘크리트 전단키 접합부의 기본극한강도식은 수정 Mohor-Coulomb의 파괴기준과 항복선의 도입에 의하여 전개하였고, 극한전단능력의 근사해는 상하계법에 의한 극치해석의 수법을 이용하여 구하고 여기에 재료의 유효강도계수를 도입하였다. 또한, 지존의 실험결과와 비교하여 그 적용성을 고찰하였다.

• Journal of Ocean Engineering and Technology
• /
• v.15 no.4
• /
• pp.86-91
• /
• 2001

In lateral ground flow, slope stability, and land slide problems, H-piles have been often used for a horizontally deforming ground to prevent the failure of mass of soil in a downward and outward movement of a slope. Here, Theoretical equations are derived to estimate the lateral force, assuming that the Mohr-coulomb's Plastic states occures in the ground just around H-piles. In this study, the mechanism of lateral force acting on passive pile that is in a row, situated in the ground undergoing plastic deformation was discussed, and its theoretical analysis was carried out considering the interval between H-piles. The solution of the theoretical equation derived from here showed resonable characteristic for constants of soil as well as for the interval, widths, and heights of H-pile.

• Geomechanics and Engineering
• /
• v.8 no.6
• /
• pp.783-799
• /
• 2015

In this study, effect of horizontal in situ stress on failure mechanism around underground openings excavated in isotropic, elastic rock zones is investigated. For estimating the plastic zone occurrence, an induced stress influence area approach (Bray Equations) was modified to define critical stress ratio according to the Mohr-Coulomb failure criterion. Results obtained from modified calculations were compared with results of some other analytical solutions for plastic zone thickness estimation and the numerical modelling (finite difference method software, FLAC2D) study. Plastic zone and its geometry around tunnels were analyzed for different in situ stress conditions. The modified equations gave similar results with those obtained from the other approaches. However, safer results were calculated using the modified equations for high in situ stress conditions and excessive ratio of horizontal to vertical in situ stresses. As the outcome of this study, the modified equations are suggested to use for estimating the plastic zone occurrence and its thickness around the tunnels with circular cross-section.