• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.345-352
• /
• 2000

It is very important to evaluate the reliable nonlinear modulus characteristics of soils not only in the analysis of geotechnical structures under working stress conditions but also for the soil dynamic problems. For the evaluation of modulus characteristics of soils, various tests have been mostly employed in laboratory. However, different testing techniques are likely to have different ranges of reliable strain measurements, different applied stress level, and different loading frequencies, and the modulus of soils can be affected by these variables. For reliable evaluation, therefore, those effects on the modulus need to be considered, and measured values should be effectively adjusted to actual conditions where the soil is working. In this paper, to evaluate the modulus characteristics of soils, laboratory testing such as free-free resonant column (FF-RC), resonant column (RC), torsional shear (TS), static TX, and cyclic M/sub R/ tests were performed. The effects of strain amplitude, loading frequency, loading cycles, confining pressure, density, and water content on modulus were investigated. It is shown that the FF-RC test, which is simple and inexpensive testing technique, can provide a reliable estimation of small strain Young's modulus (E/sub max/), and the modulus evaluated by various laboratory tests are comparable to each other fairly well when the effects of these factors are properly taken into account.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2005.03a
• /
• pp.1140-1147
• /
• 2005

The objective of this study was to identify the effect of the degree of saturation on the resilient modulus of cohesive soils as subgrade. Six representative cohesive soils representing A-4, A-6, and A-7-6 soil types collected from road construction sites across Ohio, were tested in the laboratory to determine their basic engineering properties. Resilient modulus tests were conducted on unsaturated cohesive soils at optimum moisture content, and samples compacted to optimum conditions but allowed to fully saturate. The subgrade compacted at optimum moisture content may be fully saturated due to seasonal change. Laboratory tests on fully saturated cohesive soils showed that the resilient modulus of saturated soils decreased to less than half that of soil specimens tested at optimum moisture content. The reduction of resilient modulus would possibly be caused by the buildup of pore water pressure. In resilient modulus testing performed in this study on saturated samples, pore water pressure increases were observed. Pore water pressure and residual pore water pressure gradually increased with an increase in deviator stress.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.3
• /
• pp.126-126
• /
• 2002

In dynamic analyses such as seismic ground response and soil-structure interaction problems, it is very crucial to obtain accurate dynamic shear modulus of soil deposit. In this study, an extensive data base of available experimental data is compiled and reanalyzed to establish a simple empirical formula for the dynamic shear modulus reduction curve to cover wide range of strain for sandy soils. The proposed empirical equation is to represent the dynamic shear modulus degradation with strain in terms of low-amplitude dynamic shear modulus and effective mean confining Pressure, since those factors have the most significant effect on the Position and shape of the shear modulus reduction curve for nonelastic soils. If low-amplitude shear modulus is measured, degraded modulus at any shear strain amplitude can be calculated using the proposed equation.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.3
• /
• pp.127-138
• /
• 2002

In dynamic analyses such as seismic ground response and soil-structure interaction problems, it is very crucial to obtain accurate dynamic shear modulus of soil deposit. In this study, an extensive data base of available experimental data is compiled and reanalyzed to establish a simple empirical formula for the dynamic shear modulus reduction curve to cover wide range of strain for sandy soils. The proposed empirical equation is to represent the dynamic shear modulus degradation with strain in terms of low-amplitude dynamic shear modulus and effective mean confining Pressure, since those factors have the most significant effect on the Position and shape of the shear modulus reduction curve for nonelastic soils. If low-amplitude shear modulus is measured, degraded modulus at any shear strain amplitude can be calculated using the proposed equation.

• Journal of the Korean Geotechnical Society
• /
• v.20 no.4
• /
• pp.57-63
• /
• 2004

The range of stresses experienced in subgrade soils and subbase materials in pavement under working stress conditions is below about 150㎪. Therefore, the deformational characteristics of soils at low confining pressures are important properties in the analysis and design of pavement system. Subgrade soils and subbase materials were collected from the actual pavement projects for testing. To evaluate the effect of confining pressure on modulus of those materials at low confining pressures, RC and FFRC tests were performed. Interestingly, the relationship between modulus of soils and confining pressure is more appropriate in linear space than in logarithm space at low confining pressure. Based on those results, new model fur evaluating the effects of confining pressure on modulus at low confining pressures was proposed.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2000.11a
• /
• pp.3-14
• /
• 2000

Anisotropic consolidation, shear, a transportational component during or after deposition each may produce anisotropic fabrics, which result in the anisotropic properties of soils. Nevertheless, the isotropically consolidated compression triaxial tests are commonly used in practice to determine the strength of the anisotropically consolidated soils because of their practicality and simplicity. In this paper the effects of anisotropic consolidation on the strength properties of soils are discussed. For the sandy soils consolidated under a constant vertical consolidation pressure, the deformation modulus decreases with decreasing consolidation pressure ratio($\sigma$$\sub$3c/'/$\sigma$ sub 1c/'), but the liquefaction resistance increases. For the saturated cohesive soils, both the undrained shear strength and undrained creep strength decrese with decreasing the consolidation pressure ratio. When the in-situ strength properties of the anisotropically and normally consolidated soils are determined by the isotropically consolidated tests, the undrained shear strength and creep strength of saturated cohesive soils as well as the deformation modulus of sandy soils are measured to be higher than the rear in-situ values. This, therefore, could lead to a dangerous judgement in stability analysis

• Proceedings of the Korean Geotechical Society Conference
• /
• 1994.09a
• /
• pp.259-264
• /
• 1994

The 1986 AASHTO Guide for the Design of Pavement Structures introduced the resilient modulus as a definitive material property to characterize roadbed soil. Although the incorporation of resilient modulus represents a significant acvance in pavement design practice, the test procedure for resilient modulus is complicated and time-consuming. Therefore, it is necessary to develop data base of resilient modulus for the soils frequently encountered; and to develop the reliable correlations between resilient properties and parameters from simple routine tests, In this study, resilient modulus tests were performed on five cohesive soils sampled from in-service subgrades. The stress at 1 percent axial strain in unconfined compression test(su1.0%) was found as a good indicator of the resilient modulus, and unique relationship between Mg and Su1.0% was obtained. A simple chart to estimate the resilient modulus at different levels of confining stress and deviator stress was also developed.

• Journal of the Korean Geotechnical Society
• /
• v.19 no.5
• /
• pp.69-78
• /
• 2003

In order to investigate the dynamic behavior of weathered granite soils before and after freezing-thawing, cyclic triaxial tests were conducted for the specimens not only with the variation of silt contents within 20% but with plasticity index within 20%. As the results, the dynamic shear modulus of weathered granite soils decreased with increasing silt contents. However, the change in damping ratio was negligible. The influence of freezing-thawing on shear modulus and damping ratio was minimal for the granite soils with variation of silt contents. For the case of the weathered soils with variation of plasticity index, the shear modulus increased with plasticity index within 20%, while the modulus decreased remarkably after freezing-thawing.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.3
• /
• pp.63-72
• /
• 2015

This paper describes the correlation and relationship between elastic moduli measured by three stiffness measurement methods with different mechanical characteristics to evaluate the compaction characteristics of subgrade soils. The Soil Stiffness Gauge (SSG) with very small strain (${\approx}0.001%$) ranges, static Plate Loading Test (PLT) with mid-level strain (${\approx}0.01{\sim}0.1%$) ranges, and Dynamic Cone Penetrometer (DCP) using penetration resistance were implemented to measure the elastic modulus. To use the elastic modulus measured by different measurement methods with a wide range of strain in practice, it is required to identify the correlation and relationship of measured values in advance. The comparison results of the measured elastic moduli ($E_{SSG}$, $E_{PLT}$, $E_{DCP}$) using the three measurement methods for domestic and overseas subgrade soils under various conditions indicate that the evaluated elastic modulus relies on the types of soils and the level of stress condition. The correlation analysis of the measured elastic moduli except the data of cement treated soils indicates that the static elastic modulus ($E_{PLT}$) is evaluated as about 60 to 80% of the dynamic elastic modulus ($E_{SSG}$). Unusual soils such as cement treated soils are required to be corrected by the stress correction during the correlation analysis with typical soils, because these types of soils are sensitive to the stress condition when measuring the static elastic modulus ($E_{PLT}$) of soils. In addition, when considering the use of DCP data for the evaluation of the elastic modulus ($E_{DCP}$), the measured data of the elastic modulus less than 200 MPa show more reliable correlation.

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.61-68
• /
• 2008

Resilient modulus has been used for characterizing the stress-strain behavior of subgrade soils subjected to traffic loadings. With the recent release of the M-E Design Guide, highway agencies are further encouraged to implement the resilient modulus test to improve subgrade design. The subgrade design for the trackbed, however, is primarily relying on the static test results such as $K_{30}$ and deformation modulus, Ev. Therefore applicability of the resilient modulus for the design of trackbed needs to be evaluated. In this study, physical property tests, unconfined compressive tests and resilient modulus tests were conducted to assess the resilient and permanent strain behavior of 14 cohesive subgrade soils. A predictive model for estimating the resilient modulus is proposed based on the results of unconfined compressive tests and tangent elastic modulus, unconfined compressive strength, failure strain, secant modulus at peak, and yield strain. The predicted resilient moduli using the predictive models compared satisfactorily with measured ones. Although the permanent strain occurs during the resilient modulus test, the permanent behavior of subgrade soils is currently not taken into consideration.