• Geomechanics and Engineering
• /
• v.36 no.2
• /
• pp.167-181
• /
• 2024

The soil-structure relative stiffness is a key factor affecting the seismic response of underground structures. It is of great significance to study the soil-structure relative stiffness for the soil-structure interaction and the seismic disaster reduction of subway stations. In this paper, the dynamic shear modulus ratio and damping ratio of an inhomogeneous soft soil site under different buried depths which were obtained by a one-dimensional equivalent linearization site response analysis were used as the input parameters in a 2D finite element model. A visco-elasto-plastic constitutive model based on the Mohr-Coulomb shear failure criterion combined with stiffness degradation was used to describe the plastic behavior of soil. The damage plasticity model was used to simulate the plastic behavior of concrete. The horizontal and vertical relative stiffness ratios of soil and structure were defined to study the influence of relative stiffness on the seismic response of subway stations in inhomogeneous soft soil. It is found that the compression damage to the middle columns of a subway station with a higher relative stiffness ratio is more serious while the tensile damage is slighter under the same earthquake motion. The relative stiffness has a significant influence on ground surface deformation, ground acceleration, and station structure deformation. However, the effect of the relative stiffness on the deformation of the bottom slab of the subway station is small. The research results can provide a reference for seismic fortification of subway stations in the soft soil area.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.3
• /
• pp.63-69
• /
• 2013

This paper related with the performance of SE-MMA (Signed-Error MMA) that is the reduction of computational operation number in algorithm than MMA blind eualization algorithm which are possible to elimination of intersymbol interferance in the band limited and time dispersive nonlinear communication channel. In MMA algorithm which are possible to reduction of amplitude and phase rotation by intersymbol interference that is occurred in channel without using the training sequence, it uses the error signal that is the difference of the equalizer output and constant modulus, the statisticlly characteristic of transmitted signal. But in SE-MMA, it uses the polarity of the error signal, then it is possible to reduce the updating the tap coefficient and to simplify the H/W implementation. The computer simulation were performed in order to compare the performance of SE-MMA and conventional MMA algorithm. For this, the recovered signal constellation that is the output of the equalizer, the convergence performance by MSE, MD (maximum distortion) and residual isi characteristic learning curve, SER were used. As a result of simulation, the SE-MMA has more fast convergence speed than the MMA. But in the other index after reaching the seady state, it gives more worst performance values in the used index.

• The Journal of the Acoustical Society of Korea
• /
• v.16 no.3
• /
• pp.73-80
• /
• 1997

This paper describes structural optimization of optical fiber-wound mandrel hydrophones with Finite Element Method (FEM). The hydrophone is supposed to have operation frequency range of up to 10 kHz and show omni-directional sensitivity pattern at 5 kHz. Studied parameters are mandrel geometry, molding thickness, and material properties of constitutional parts of the hydrophone. Theoretical calculation result shows that pressure sensitivity of the hydrophone increased as either mandrel length or molding thickness gets larger. Also higher pressure sensitivity requires a mandrel or molding material with relatively low Youngs modulus or Poissons ratio. Hydrophone bandwidth increases either as the mandrel length becomes shorter or as the mandrel becomes harder. The omni-directional characteristic is improved as the mandrel length becomes shorter, at 5 kHz. With the above results, we determine the structure of an optical fiber-wound mandrel hydrophone which has the pressure sensitivity of $30 {\times} 10_{-7}$ Rad./Pa, operation frequency range of up to 10 kHz, and shows omni-directional sensitivity pattern at 5 kHz.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.4
• /
• pp.51-57
• /
• 2003

The development of the communication network and the other network method can generate serious social problems. So, it is highly required to control security of network. These problems related security will be developed and keep up to confront with anti-security field such as hacking, cracking. The way to preserve security from hacker or cracker without developing new cryptographic algorithm is keeping the state of anti-cryptanalysis in a prescribed time by means of extending key-length. In this paper, we proposed M3 algorithm for the reduced processing time in the montgomery multiplication part. Proposed M3 algorithm using the matrix function M(.) and lookup table perform optionally montgomery multiplication with repeated operation. In this result, modified repeated operation part produce 30% processing rate than existed montgomery multiplicator. The proposed montgomery multiplication structured unit array method in carry generated part and variable length multiplication for eliminating bottle neck effect with the RSA cryptosystem. Therefore, this proposed montgomery multiplier enforce the real time processing and prevent outer cracking.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.27 no.9C
• /
• pp.861-870
• /
• 2002

In this paper, with targeting on the drawback of RSA of operation speed, a new 1024-bit RSA cryptosystem has been proposed and implemented in hardware to increase the operational speed and perform the variable-length encryption. The proposed cryptosystem mainly consists of the modular exponentiation part and the modular multiplication part. For the modular exponentiation, the RL-binary method, which performs squaring and modular multiplying in parallel, was improved, and then applied. And 4-stage CSA structure and radix-4 booth algorithm were applied to enhance the variable-length operation and reduce the number of partial product in modular multiplication arithmetic. The proposed RSA cryptosystem which can calculate at most 1024 bits at a tittle was mapped into the integrated circuit using the Hynix Phantom Cell Library for Hynix 0.35㎛ 2-Poly 4-Metal CMOS process. Also, the result of software implementation, which had been programmed prior to the hardware research, has been used to verify the operation of the hardware system. The size of the result from the hardware implementation was about 190k gate count and the operational clock frequency was 150㎒. By considering a variable-length of modulus number, the baud rate of the proposed scheme is one and half times faster than the previous works. Therefore, the proposed high speed variable-length RSA cryptosystem should be able to be used in various information security system which requires high speed operation.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.877-880
• /
• 2005

This paper describes a PLL frequency synthesizer for wireless LNA applications. The design is focused mainly on low-power and low-phase noise characteristics. A 128/129 dual-modulus prescaler has been designed using the proposed TSPC D flip-flops for high-speed operation and low-power consumption The designed synthesizer includes all building blocks for elimination of external components, other than the crystal. Its operating frequency can be programmed by external data. The frequency synthesizer has been designed using a $0.25{\mu}m$ CMOS process parameters. It operates in the frequency range of 2GHz to 3GHz and consumes 3.2mA at 2.5GHz from a 2.5V supply.

• Journal of Mechanical Science and Technology
• /
• v.18 no.6
• /
• pp.904-914
• /
• 2004

The fiber reinforced composite material is widely used in the multi-industrial field because of their high specific modulus and specific strength. It has two main merits which are to cut down energy by reducing weight and to prevent explosive damage proceeding to the sudden bursting which is generated by the pressure leakage condition. Therefore, Pressure vessels using this composite material can be applied in the field such as defence industry and aerospace industry. In this paper, for nonlinear finite element analysis of E-glass/epoxy filament winding of composite vessel subjected to internal pressure, the standard interpretation model is developed by using the ANSYS with AutoLISP and ANSYS APDL languages, general commercial software, which is verified as useful characteristic of the solution. Among the modules of the system, both the process planning module for carrying out the process planning of filament wound composite pressure vessel and the autofrettage process module for obtaining higher residual stress will minimize trial and error and reduce the period for developing new products. The system can serve as a valuable system for experts and as a dependable training aid for beginners.

• Structural Engineering and Mechanics
• /
• v.62 no.5
• /
• pp.587-593
• /
• 2017

The objective of this analytical study is to calculate the elasto-plastic stresses of Functionally Graded (FG) hyperbolic disc subjected to uniform temperature. The material properties (elastic modulus, thermal expansion coefficient and yield strength) and the geometry (thickness) of the disc are assumed to vary radially with a power law function, but Poisson's ratio does not vary. FG disc material is assumed to be non-work hardening. Radial and tangential stresses are obtained for various thickness profile, temperature and material properties. The results indicate that thickness profile and volume fractions of constituent materials play very important role on the thermal stresses of the FG hyperbolic discs. It is seen that thermal stresses in a disc with variable thickness are lower than those with constant thickness at the same temperature. As a result of this, variations in the thickness profile increase the operation temperature. Moreover, thickness variation in the discs provides a significant weight reduction. A disc with lower rigidity at the inner surface according to the outer surface should be selected to obtain almost homogenous stress distribution and to increase resistance to temperature. So, discs, which have more rigid region at the outer surface, are more useful in terms of resistance to temperature.

• Journal of KIISE:Computer Systems and Theory
• /
• v.30 no.2
• /
• pp.93-98
• /
• 2003

This paper presents two new algorithms and their architectures for $AB^2 $ multiplication over $GF(2^m)$.First, a new architecture with a new algorithm is designed based on LFSR (Linear Feedback Shift Register) architecture. Furthermore, modified $AB^2 $ multiplier is derived from the multiplier. The multipliers and the structure use AOP (All One Polynomial) as a modulus, which hat the properties of ail coefficients with 1. Simulation results thews that proposed architecture has lower hardware complexity than previous architectures. They could be. Therefore it is useful for implementing the exponential ion architecture, which is the tore operation In public-key cryptosystems.

• The Journal of Advanced Prosthodontics
• /
• v.8 no.5
• /
• pp.372-379
• /
• 2016

PURPOSE. Alginate mixers available in the market do not have the automatic proportioning unit. In this study, an automatic proportioning unit for the alginate mixer and controller software were designed and produced for a new automatic proportioning unit. With this device, it was ensured that proportioning operation could arrange weight-based alginate impression materials. MATERIALS AND METHODS. The variation of coefficient in the tested groups was compared with the manual proportioning. Compression tension and tear tests were conducted to determine the mechanical properties of alginate impression materials. The experimental data were statistically analyzed using one way ANOVA and Tukey test at the 0.05 level of significance. RESULTS. No statistically significant differences in modulus of elastisity (P>0.3), tensional/compresional strength (P>0.3), resilience (P>0.2), strain in failure (P>0.4), and tear energy (P>0.7) of alginate impression materials were seen. However, a decrease in the standard deviation of tested groups was observed when the customized machine was used. To verify the efficiency of the system, powder and powder/water mixing were weighed and significant decrease was observed. CONCLUSION. It was possible to obtain more mechanically stable alginate impression materials by using the custom-made proportioning unit.