• Journal of Biosystems Engineering
• /
• 제33권5호
• /
• pp.326-332
• /
• 2008

A respiration measurement system for vital signs was developed. Respiration signals were measured, processed, and analyzed. Four electrodes, attached on the surface of the skin, were used to monitor respiration signals by impedance pneumography. The measured signals were amplified, detrended, filtered, and transferred toan embedded module. The Kalman filter was used to remove motion artifact from the respiration signals. Experiments were conducted at stable condition and walking condition to evaluate the performance of the system. Respiration rates of five males and five females were measured and analyzed at each condition. The referenced respiration signal was determined by temperature of nose surroundings. The results showed that the respiration rates at the walking condition had more motion artifacts than the stable condition. The accuracies of the respiration measurement system with Kalman filter were found as 96% at the stable condition and 95% at the walking condition. The results showed that the Kalman filter was an effective tool to remove the motion artifact from the respiration signal.

• Current Photovoltaic Research
• /
• 제4권2호
• /
• pp.59-63
• /
• 2016

A key point of a soldering process for photovoltaic (PV) modules is to increase an adhesive strength leading a low resistivity between ribbon and cell. In this study, we intended to optimize a heating condition for the soldering process and characterize the soldered joint via physical and chemical analysis methods. For the purpose, the heating conditions were adjusted by IR lamp power, heating time and hot plate temperature for preheating a cell. Since then the peel test for the ribbon and cell was conducted, consequently the peel strength data shows that there is some optimum soldering condition. In here, we observed that the peel strength was modified by increasing the heating condition. Such a soldering property is affected by a various factors of which the soldered joint, flux and bus bar of the cell are changed on the heating condition. Therefore, we tried to reveal causes determining the soldering property through analyzing the soldered interface.

• 전력전자학회논문지
• /
• 제8권4호
• /
• pp.313-320
• /
• 2003

본 논문에서는 부가적인 회로의 추가 없이 IPM 내부 IGBT의 게이트 저항을 시스템에 최적화된 값으로 선정하여 dv/dt 및 di/dt를 감소시키고 이로 인한 전도 EMI 노이즈를 저감하여 엘리베이터 시스템에 최적화된 전련변환장치를 설계한다. 주문형 IPM을 엘리베이터용 인버터 시스템에 최적화하기 위하여 시스템에 적용될 전력변환장치의 게이트 저항에 따른 Spike 전압 및 전동기 서지전압, 스위칭 손실에 따른 IPM 케이스와 방열판의 온도 변화등을 시뮬레이션 및 계측한다. 결과적으로 IPM의 게이트 저항을 시스템에서 요구하는 수명에 따라 최적화하여 전도되는 EMI 노이즈가 특정 주파수 대역에서 약 5∼10 [dB$\mu$Vl 저감됨을 확인할 수 있다.

• KIEAE Journal
• /
• 제13권6호
• /
• pp.105-111
• /
• 2013

This study aims to suggest the PV lightshelf and to evaluate the power performance of the photovoltaic systems easily mounted on the windows. For the study, the suggested systems consist of two parts as fixed and movable PV modules. Also, tempered glass and polycarbonate are used on the surface protection materials for solar cells of PV lightshelf. By using polycarbonate, the weight of PV lightshelf is lighter about 20%. The field tests are performed for five days by using real size models. The voltage, current and electric powers are measured as basic performances of PV lightshelf. Also, the irradiation, brightness and module surface temperature are measured as outside conditions. As results, the power performance of tempered glass PV lightshelf shows about 11(%) higher thant that of polycarbonate PV lightshelf. And the power performance shows about 5(%) higher in a horizontal system. This results could be used to develop the effective PV lightshelf in next study.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.541-544
• /
• 2002

In this study, a new LTCC material using $ZnWO_4$-LiF system was attempted with respect to use as a capacitor layer in Front-End Module. Pure $ZnWO_4$ must be sintered above $1050^{\circ}C$ in order to obtain up to 98% of full density. It's measured dielectric constant, quality factor, and temperature coefficient of resonant frequency were 15.5, 74380GHz, and $-70ppm/^{\circ}C$, respectively. LiF addition resulted in an liquid phase formation at $810^{\circ}C$ due to interaction between $ZnWO_4$ and LiF. Therefore $ZnWO_4$ with 0.5~1.5wt% LiF could be densified at $850^{\circ}C$. Addition of LiF slightly lowered the dielectric constant from 15.5 to 14.2~15. In the given LiF addition range, the sintering shrinkage increased with increasing LiF content. $Q{\times}fo$ value, however, decreased with increasing LiF content(or increasing densification). This is originated from the interaction between the liquid phase and $ZnWO_4$ and inhomogeneity of grain morphology.

• 한국태양에너지학회 논문집
• /
• 제25권3호
• /
• pp.69-75
• /
• 2005

The PV-Solarwall system has been introduced as a promising alternative to harness solar energy for both heating applications and electricity generation simultaneously. The system comprises a PV solar panel(for electricity generation). In addition, the solarwall incorporates a fan strategically located behind the PV panel to bring the warm and fresh air from the solarwall into the room. Because of its location and convective cooling principle, the fan also serves to reduce the operating temperature of the PV panel thereby increasing its efficiency. So this PV-Solarwall system holds much promise for saving heating and electricity costs compared with a PV system without solarwall. In particular, by controlling the tilt angle of the entire PV-Solarwall system between $0^{\circ}$(horizontal) and $90^{\circ}$(vertical), the performance of the system can be further evaluated. It is expected that the range of tilt angle PV-Solarwall between $40^{\circ}$ and $50^{\circ}$ will improve the output of the system.

• 상하수도학회지
• /
• 제21권2호
• /
• pp.195-201
• /
• 2007

A submerged flat-sheet membrane separation system integrated with PAC (powdered activated carbon) was used in this research in order to investigate the effects of PAC on the efficiencies of operation and treatment and to evaluate the performance of the system. The experiments were carried out under operating conditions of a filtration rate of 0.38 m/d, water temperature of $20-28^{\circ}C$, and PAC dose of 0 g/L (Run-A) and 20 g/L (Run-B). The influent concentrations of TOC (total organic carbon), $NH_4{^+}-N$ (ammonia nitrogen) and $UV_{254}$ (UV absorbance at 254 nm) were 2.48 mg/L, 1.4 mg/L and 2.53 1/m, respectively. TOC removal of 43.2 and 73.6%, ammonia nitrogen removal of 4.9 and 15.9%, and $UV_{254}$ removal of 20.6 and 31.6% were obtained for Run-A and Run-B, respectively. During an experimental period of 33 days, no change was found in TMP (Run-B), but the TMP in Run-A increased by 5 kPa after 29 days. This research showed that the filtrate quality and the performance efficiency were enhanced when PAC was introduced into the filtration system.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2006년도 6th International Meeting on Information Display
• /
• pp.150-155
• /
• 2006

Carbon nanotubes backlight unit (CNT-BLU) that lightened by field emission was developed into practicability. According to our novel structure, AC mode circuit design and simple printing process, CNT-BLU could achieve 85% of uniformity, 8000 nits of brightness and low material and fabrication cost. Based on these performances, this new planar backlight technology has chances to proceed to mass production and has the potential to replace traditional backlight technology because of its good properties, like the simple processes, easy to large scale, low surface temperature, low power consumption, optical film-free and Hg-free, etc.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2003년도 하계학술대회 논문집 Vol.4 No.2
• /
• pp.751-755
• /
• 2003

In this paper, We proposed compact multi-layer LTCC (Low Temperature Cofired Ceramic) bandpass filter for Bluetooth module. A ${\lambda}/4$ coupled stripline resonators are designed, which composed of coupled strip-line section and loading capacitance. This resonator with a loading capacitor has slow-wave characteristics. Due to the slow-wave effect of the proposed resonator, it is possible to design and fabricate a compact bandpass filter with a wide upper stop band. Attenuation poles in the lower stop band are achieved using controlling of electro-magnetic coupling between resonators. Using multi-layer LTCC technology, we designed and fabricated band pass filter with a finite attenuation pole and wide upper stopband. The overall size of the filter is $1.2{\times}2.0{\times}1.0mm^3$.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2009년도 정보 및 제어 심포지움 논문집
• /
• pp.48-50
• /
• 2009

This paper presents an IAQ(Indoor Air Quality) Monitoring System using equipments for measurement of fine Particle($PM1{\sim}PM10$), $CO_2$, VOCs(Volatile Organic Compounds), temperature and humidity for IAQ monitoring of subway station which millions of people use a day. The necessity of IAQ monitoring system is getting increased for more effective subway station monitoring in line with the recent government's regulation for IAQ is reinforcing. Subway Station is an unusual case. The structure of subway station is closed and complicated. Therefore when data of equipments are transferred, transmission error can happen occasionally. To prevent transmission error, an IAQ Monitoring System is needed the appropriate position and selection of equipments or sensor module. In addition IT(Information Technology) can be utilized like "WiBro(Wireless Broadband)" and "GateWay" for facilitate movement of data and construction of IAQ monitoring system of subway station.