• 전기학회논문지
• /
• 제65권5호
• /
• pp.804-810
• /
• 2016

Photovoltaic system construction of the module capacity in domestic is specified criteria to less than 105% of the inverter capacity. However, the modules are installed in the outdoor actual output is reduced due to factors such as the irradiation intensity, module surface temperature. Thus, it needs the capacity of the inverter to be designed according to the actual module output. In this paper, the first approach to find the actual module output is to analyze the actual PV system monitoring data. Next, four sites where the loss analysis, system utilization, inverter utilization, and the ratio of the inverter overload are performed using PVSYST software. By changing the ratio of the module capacity, the inverter capacity of the site B is confirmed 20% less than the module capacity. Site A, C, D are identified as the ratio of the inverter capacity is 10% less than the module capacity.

• 전기학회논문지
• /
• 제66권7호
• /
• pp.1155-1161
• /
• 2017

This study examines environmental performance of the arcing measurement module according to international standards. The module assesses the collected current performance using a computer system. The module is required to assess environmental impact resulting from electromagnetic waves, shock and temperature change during train operation. The test includes testing EMI/EMC, vibration, shock and temperature cycling for interface between trains and the arcing measurement module. The module test items were determined in compliance with the standards suggested by the International Electrotechnical Commission (IEC) and Europaische Norm (EN). This study describes the method of test, test equipment operation and how to choose relevant performance standards. The analysis and test results of environmental performance for the module based on computer system are described in this study.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.1231-1236
• /
• 2007

Balance Shaft Module is module parts that is installed to vehicles engine to reduce noise and vibration of vehicles engine. Balance Shaft Module's performance exerts important influence on performance of engine. Therefore, must be able to warrant quality and performance of Balance Shaft Module. Existing product found and revised error at continuous process of production, and estimated failure mode in Balance Shaft Module. Previous method hard to secure product that performance is excellent, and bring a lot of damages economically. Therefore, development of inspectin system for quality inspection of parts and performance test of assembly is essential in Balance Shaft Module. In this study, represented development process of automatic dynamic inspection system to test performance and detect breakdown of Balance Shaft Module that is producing in Dongbo.

• 전기학회논문지P
• /
• 제58권4호
• /
• pp.377-384
• /
• 2009

In this paper, leakage current sensing module of SoC(System on Chip)type and real time monitoring system under consideration of electromagnetic interface in power trunk line are developed. The first, leakage current sensing module of SoC type under consideration of electromagnetic interface is developed, and the developed sensing module of SoC type is composed of leakage sensing part, power supply part, interface part, communication part, AD(Alternating current to Direct current)convert part and amplification part. And also the electromagnetic compatibility is evaluated by conduction and radiation of EMI(Electromagnetic Interference) for developed sensing module. The developed system can have confidence, stability and do energy saving under mixed electric circumstance of the low voltage communication device and high voltage equipment. The second, the real time remote monitoring system is developed using designed wire and wireless communication module with leakage current sensing module of SoC type. The developed real time remote monitoring system can monitor sensing state, occurrence state of leakage current and alarm for each step etc.. And the device configuration, PCB layout for leakage current sensing module of system on chip type and the experiment configuration in consideration of EMI are presented. Also the measurement results of conduction and radiation for EMI are presented.

• 한국정보과학회논문지:정보통신
• /
• 제29권6호
• /
• pp.635-644
• /
• 2002

본 논문은 웹 시스템 환경에서 안전한 데이타 전송을 만족하는 Protocol-Based Security Module(PBSM) 구조를 제안한다. PBSM 구조는 크게 두개의 모듈로 구성된다. 하나는 웹 서버에서 동작하는 Web Server Sorority Module(WSSM)이고, 다른 하나는 클라이언트에서 동작하는 Winsock Client Security Module(WSCSM)이다. WSCSM 보안 모듈은 WSSM으로부터 받은 암호된 메시지를 정상적인 메시지로 변환하여 웹 브라우저에 나타나게 한다. WSSM 보안 모듈은 HTML 파일에 대한 암호화(Encryption)기능과 WSCSM 모듈로부터 받은 Common Gateway Interface(CGI) 데이타에 대한 복호화 기능을 가지고 있다. PBSM 보안 시스템의 보안 정확성을 검증하기 위하여 정형화 분석 기법을 이용했다.

• 한국컴퓨터산업학회논문지
• /
• 제6권5호
• /
• pp.821-828
• /
• 2005

This paper was proposed Intelligent and wireless USN/RFID module system that can overcome disadvantage of existing RFID system with no sensing module and wire communication. The proposed USN/RFID system was designed and fabricated. After fabricating new system, we analyzed the characteristics of USN/RFID module. After design VCO block that is point circuit to develop next generation system one chip of RFID system. we were carried out simulation and verified the validity, this paper was showed that VCO system was enough usable in wireless network module. USN/RFID Reader module shows superior result that validity awareness distance corresponds to 30M in the case of USN and to 5M in RFID Reader's case and 900MHz of commercial frequency does practical use enoughly in range of high frequency. The USN/RFID Reader module is considered to act big role to Ubiqitous industry offering computing surrounding of new concept that is intelligence type service and that was associated to real time location system(RTLS). environment improvement/supervision. national defense, traffic administration etc.

• 대한전기학회논문지:전력기술부문A
• /
• 제48권11호
• /
• pp.1410-1416
• /
• 1999

This paper aims at investigating the operating-mode characteristics of two-module Thyristor Controlled Series Compensator (TCSC) as an equivalent of the multi-module TCSC in a simple three-phase power transmission system. The load flow program is developed to analyze the steady-state characteristics of two-module TCSC system and to find the thyristor firing angles for the required real power flow. The stability calculation program is developed with Poincare mapping theory. Simulation studies of the TCSC power transmission system using EMTP are performed to evaluate the transient characteristics of two-module TCSC as a real power flow controller and to rpove the results of the load flow calculation and the stability analysis. In the process of the study, the operating-mode characteristics of two-module TCSC are evaluated and compared to those of single-module TCSC.

• 한국정밀공학회지
• /
• 제8권1호
• /
• pp.105-115
• /
• 1991

This paper describes an integrated CAD and CAPP system for prismatic parts of injection mold which generates a complete process plan automatically from CAD data of a part without human intervention. This system employs Auto CAD as a CAD model and GS-CAPP as an automatic process planning system for injection mold. The proposed CAD/CAPP system consists of three modules such as CAD data conversion module, manufacturing feature recognition module, and CAD/CAPP interface module. CAD data conversion module transforms design data of AutoCAD into three dimensional part data. Manufacturing feature recognition module extracts specific manufacturing features of a part using feature recognition rule base. Each feature can be recognized by combining geometry, position and size of the feature. CAD/CAPP interface module links manufacturing feature codes and other head data to automatic process planning system. The CAD/CAPP system can improve the efficiency of process planning activities and reduce the time required for process planning. This system can provide a basis for the development of part feature based design by analyzing manufacturing features.

• 조명전기설비학회논문지
• /
• 제28권2호
• /
• pp.31-41
• /
• 2014

This paper proposes the configuration of photovoltaic(PV) module considering the environment conditions of the PV system. The PV system is consisted of the series-parallel connection of the PV module. When shadows or changes of the radiation or an electrical characteristic in the solar cell are happened to PV system, the serious power loss will occur. If the PV module connected in series has the shadows, the output current is restricted to current of shaded PV module. Also if shadow is occurred to the parallel connection PV module, the output voltage is limited to voltage of shaded PV module. These problems are caused power loss. Therefore, this paper proposes the method that makes the output power of the PV module equalize by reconfiguration of PV module using the switching considering these environment conditions. A validity of the method proposed in this paper proves through comparing with performance of conventional PV module.

• 전기학회논문지P
• /
• 제53권4호
• /
• pp.190-194
• /
• 2004

In this paper, UPS, which is embedded in computer power supply, is developed against the poor utility power system. In the developed system, PIC16C54 is used as the main controller, and UPS system consists of micom control module, power failure detecting module, charging module, power module, synchronous transfer module, and GUI module. Additionally, GUI module consists of battery charging state unit, power operating unit and operating state unit. The effectiveness of the developed system has been verified by the experimental results.