• Journal of Information Processing Systems
• /
• v.15 no.3
• /
• pp.670-681
• /
• 2019

Orthogonal frequency division multiplexing (OFDM) is a system which is used to encode data using multiple carriers instead of the traditional single carrier system. This method improves the spectral efficiency (optimum use of bandwidth). It also lessens the effect of fading and intersymbol interference (ISI). In 1995, digital audio broadcast (DAB) adopted OFDM as the first standard using OFDM. Later in 1997, it was adopted for digital video broadcast (DVB). Currently, it has been adopted for WiMAX and LTE standards. In this project, a Verilog design is employed to implement an OFDM transmitter (DAC block) and receiver (FFT and ADC block). Generally, OFDM uses FFT and IFFT for modulation and demodulation. In this paper, 16-point FFT decimation-in-frequency (DIF) with the radix-2 algorithm and direct summation method have been analyzed. ADC and DAC in OFDM are used for conversion of the signal from analog to digital or vice-versa has also been analyzed. All the designs are simulated using Verilog on ModelSim simulator. The result generated from the FFT block after Verilog simulation has also been verified with MATLAB.

• Journal of Korea Multimedia Society
• /
• v.22 no.9
• /
• pp.1011-1019
• /
• 2019

In this paper, we propose a system that can more precisely identify and monitor the position of the tool used in the assembling workplace such as automobile production. The proposed positioning monitoring system is a combination of UWB communication module and MEMS IMU sensor. Since UWB does not need modulation and demodulation function and has low power density, UWB is widely used in indoor positioning field. However, it may cause positioning error due to errors in RF transmission and reception process, which may cause positioning accuracy. Therefore, in this paper, we propose an algorithm that uses IMU as an auxiliary means to compensate for errors that may occur in positioning using only UWB. The tag and anchor of UWB module measure the transmission / reception time by transmitting signals to each other and then estimate the distance between tag and anchor. The MEMS IMU sensor serves to provide positioning calibration information. The tag, which is a mobile node and attached to a moving tool, measures the three-dimensional position of the tool and transfers the coordinate data to the anchor. Thus, it is possible to confirm whether or not the specific tool is properly used according to the prescribed regulations.

• Journal of Broadcast Engineering
• /
• v.24 no.3
• /
• pp.485-494
• /
• 2019

A software-driven real-time frequency de-modulator is implemented with the aid of universal-serial-bus (USB) type software defined radio dongle. An analog stereo frequency modulation (FM) broadcast signal is down-converted to the basedband analog signal then converted to digital bit streams in the USB dongle. Computer software such as Matlab, Python, and GNU Radio manipulates the incoming bit streams with the technique of digital signal processing. Low pass filtering, band pass filtering, decimation, frequency discriminator, double sideband amplitude demodulation, phase locked loop, and deemphasis function blocks are implemented using such computer languages. Especially, GNU Radion is employed to realize the real-time demodulator.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38A no.12
• /
• pp.1030-1038
• /
• 2013

The proposed Alamouti coded OFDM effectively cancels Inter Carrier Interference (ICI) due to frequency offset between distributed antennas. The conventional Alamouti coded OFDM schemes to mitigate ICI utilize N-point Inverse Fast Fourier Transform/Fast Fourier Transform (IFFT/FFT) operations for OFDM modulation and demodulation processes with total N subcarriers. However, the performance degrades because ICI is also repeated in N periods due to the property of N-point IFFT/FFT operation. In order to avoid this problem, null data are used at the subcarriers with large ICI and thus, data rate decreases. The proposed scheme employs 2N-point IFFT/FFT instead of N-point IFFT/FFT in order to increase sampling rate. By increasing sampling rate, the amount of interference significantly decreases because the period of ICI also increases. The proposed scheme increases the data rate and improves the performance by reducing amount of ICI and the number of null-data. Furthermore, the gain of the performance and data rate of the proposed scheme is significant with higher modulation such as 16-Quadarature Amplitude Modulation (QAM) or 64-QAM.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.3
• /
• pp.697-707
• /
• 2015

This paper covered the design and implementation of the demodulation receiver in the ADS-B 1090ES system, which is one of the CNS/ATM's surveillance systems. This researched demodulation performed at the level required by RTCA DO-268B and EUROCAE ED-129. The single signal process method, which applies a baseline multi-sample technique among multi-amplitude sample demodulations, was suggested to improve the quality of the receiver signal, the dynamic range and so on. The suggested multi-signal level tuning method has enhanced the single-signal process method, reducing the unstable reception ratio by the transmit output level difference and manufacturing receiver hardware. The result was that the receiver suggested by the method had 0~87dBm in dynamic range and -90dBm in MTL. This shows a better performance by -3dBm less than the international standard in ADS-B 1090ES ground receiver equipment. The systems which use a similar modulation method, will be considered to be widely applied.

• International Journal of Computer Science & Network Security
• /
• v.23 no.10
• /
• pp.1-10
• /
• 2023

This paper proposes a method to extend Inter-Carrier Interference (ICI) canceling Orthogonal Frequency Division Multiplexing (OFDM) receivers for 5G mobile systems to spatial multiplexing 2×2 MIMO (Multiple Input Multiple Output) systems to support high-speed ground transportation services by linear motor cars traveling at 500 km/h. In Japan, linear-motor high-speed ground transportation service is scheduled to begin in 2027. To expand the coverage area of base stations, 5G mobile systems in high-speed moving trains will have multiple base station antennas transmitting the same downlink (DL) signal, forming an expanded cell size along the train rails. 5G terminals in a fast-moving train can cause the forward and backward antenna signals to be Doppler-shifted in opposite directions, so the receiver in the train may have trouble estimating the exact channel transfer function (CTF) for demodulation. A receiver in such high-speed train sees the transmission channel which is composed of multiple Doppler-shifted propagation paths. Then, a loss of sub-carrier orthogonality due to Doppler-spread channels causes ICI. The ICI Canceller is realized by the following three steps. First, using the Demodulation Reference Symbol (DMRS) pilot signals, it analyzes three parameters such as attenuation, relative delay, and Doppler-shift of each multi-path component. Secondly, based on the sets of three parameters, Channel Transfer Function (CTF) of sender sub-carrier number n to receiver sub-carrier number l is generated. In case of n≠l, the CTF corresponds to ICI factor. Thirdly, since ICI factor is obtained, by applying ICI reverse operation by Multi-Tap Equalizer, ICI canceling can be realized. ICI canceling performance has been simulated assuming severe channel condition such as 500 km/h, 8 path reverse Doppler Shift for QPSK, 16QAM, 64QAM and 256QAM modulations. In particular, 2×2MIMO QPSK and 16QAM modulation schemes, BER (Bit Error Rate) improvement was observed when the number of taps in the multi-tap equalizer was set to 31 or more taps, at a moving speed of 500 km/h and in an 8-pass reverse doppler shift environment.

• The Journal of the Acoustical Society of Korea
• /
• v.23 no.1
• /
• pp.24-29
• /
• 2004

In ocean acoustic tomography (OAT), the pulse compression techniques using M-sequences are employed in the many studies for investigating the ocean structures. M-sequences can provide the good time and Doppler resolution in the process of demodulation using matched-filter. The signal-to-noise (SNR) performance at the output of receiver may be improved by manipulating received signal, i. e. coherently averaging. The processing time can be significantly reduced by using fast hadarmard transform (FHT) or fast Fourier transform (FFT). In this paper, we estimate the multipath arrival structures and delay times using the East Korean Sea experiment data and explore the compensation method for the detrimental effects on performance due to sampling rate error. We also analyze the characteristics of the ocean acoustic channels through scattering function, delay power profile, and time dispersions.

• Journal of Biomedical Engineering Research
• /
• v.16 no.1
• /
• pp.95-100
• /
• 1995

In this study, we have evaluated the effect of amplitude and frequency perturbation of EGG signal for single vowels associated with laryngeal pathology. The normal EGG signal was properly characterized by an autoregressive model which has an optimal order of ninth using the parametric method. This can be analyzed by determining the transfer function. Perturbations in the fundamental pitch and in the peak amplitude of EGG signal measured with a four-electrode system using the modulation/demodulation techniques were investigated for the purpose of developing a decision criteria for the laryngeal function analysis. The abnormal EGG signal has nonperiodic and unstable characteristics. It can be discriminated by the calculation of opening and closing time of glottis using the EGG signal. In case of normal and abnormal subjects, m$\pm$0.5*sd was discriminating line for frequency perturbation and m$\pm$2*sd for normal amplitude perturbations, respectively. Also, The normal and abnormal cases of the subjects can be discriminated effectively using the pattern of attractor derived with Hilbert transform of EGG signal.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2007.06a
• /
• pp.754-757
• /
• 2007

In this paper, we present an implementation and it's real-sea test of an underwater acoustic data communication system, which allows the system to reduce complexity and increase robustness in time variant underwater environments. For easy adaptation to complicated and time-varying environments of the ocean, all-digital transmitter and receiver systems were implemented. For frame synchronization the CAZAC sequence was used, and QPSK modulation/ demodulation method with carrier frequency of 25kHz and a bandwidth of 5kHz were applied to generate 10kbps transmission rate including overhead. To improve transmission quality, we used several techniques and algorithms such as adaptive beamforming, adaptive equalizer, and convolution coding/Viterbi decoding. for the verification of the system performance, measurement of BER has been done in a very shallow water with depth of 8m at JangMok, Geoje. During the experiment, image data were successfully transmitted up to about 7.4km.

• Convergence Security Journal
• /
• v.14 no.7
• /
• pp.29-36
• /
• 2014

In this study, we design and develop a VLC test-bed system which has been recently issued and focused as good convergence technology in the world. We classify the developed system into transmission part including analog LED driver module, digital signal modulation module, and receiver part with light sensing module and signal demodulation module. Then we introduce important characteristics and components. We analyze some factors for each module. To validate the communication of the designed VLC system, we develop a VLC sender-receiver simulator which can control the dimming factor and flicker-free effect. From the developed system, we observed about 12Mbps of data transmission rate with 0.5m~1m of distance, without packet loss. We verified the real-time communication with multimedia streaming which can be considered as very high date rate. The developed system and technology will be useful for some converged data services like indoor positing, home appliances, and indoor parking system.