• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2017.11a
• /
• pp.30-31
• /
• 2017

The objective of this study is to evaluate the performance of polymer-modified surface preparation mortars with pozzolanic materials for corrosion prevention method in deteriorated sewage treatment structures. The prepackaged-type surface preparation mortars are prepared with a polymer-binder ratio of 10%, ground granulated blast furnace slag contents of 0, 15, 30%, a fly ash content of 15%. And, the specimens are tested for workability, adhesion in tension, water absorption, crack and impact resistance. As a result, the prepackage-type surface preparation mortars for sewage treatment structure are satisfied with quality requirements by KS F 4716, Japan sewage work agency(JS) and JIS A 6916 for surface preparation mortars.

• Elastomers and Composites
• /
• v.54 no.3
• /
• pp.182-187
• /
• 2019

To improve the mechanical properties of glass-fiber-reinforced polypropylene (PP) composites through interfacial adhesion control between the PP matrix and glass fiber, the surface of the glass fiber was modified with PP-graft-maleic anhydride (MAPP). Surface modification of the glass fiber was carried out through the well-known hydrolysis-condensation reaction using 3-aminopropyltriethoxy silane, and then subsequently treated with MAPP to produce the desired MAPP-anchored glass fiber (MAPP-a-GF). The glass-fiber-reinforced PP composites were prepared by typical melt-mixing technique. The effect of chemical modification of the glass fiber surface on the mechanical properties of composites was investigated. The resulting mechanical and morphological properties showed improved interfacial adhesion between the MAPP-a-GF and PP matrix in the composites.

• Journal of Adhesion and Interface
• /
• v.5 no.2
• /
• pp.1-7
• /
• 2004

A novel carboxyl terminated butadiene-acrylonitrile (CTBN) modified, low temperature cure epoxy film adhesive was developed in this paper. It can be cured at as low as $75^{\circ}C$ for 4 hours with a pressure of 0.1MPa. After post cure at $120^{\circ}C$ for 2 hours, the bonding strengths of Phosphoric Acid Anodizing(PAA) surface treated aluminum adherend were similar to those of structural film adhesives curing at $120^{\circ}C$. It is suitable to bond both metal/composite laminate-to-laminate and laminate to honeycomb structure.

• Korean Journal of Cleft Lip And Palate
• /
• v.7 no.1
• /
• pp.1-16
• /
• 2004

In the recent time, early correction of the congenital anomalies has become the focus of contemporary cleft lip care, The reason of that is mostly psychologic factor of children are respected, Although the propound object of lip adhesion is not esthetic improvement, that able to satisfy sufficiently parents of cleft children, In the unilateral or bilateral clefts, a preliminary lip adhesion has been advocated as a mean of narrowing the cleft at an early phase, of improving the nasal contour, of molding the alveolar arch, and of easing and improving the result of a definitive lip repair. The present study was earned out to investigate the effect of lip adhesion. We performed the Millard's high-half underminded adhesion and Seibert's lip adhesion followed by modified Millard's cheiloplasty for five infants had unilateral complete cleft lip. The lip adhesion reduced the actual deformity by molding the maxillary alveolar segments into better relationship and allows a easy cheiloplasty so that led to more perfect final lip result, Both Millard's high-half underminded adhesion and Seibert's lip adhesion were available methods to adhere a wide cleft lip, Especially, Seibert's lip adhesion had more advantages such as enhancement of the force of adhesion, correction of the deviated columella and acquirement of the esthetic upper lip continuity. These results suggest that the lip adhesion followed by cheiloplasty for wide unilateral complete cleft lip patients provide more favorable final result by molding the maxillary alveolar segments into better relationship.

• 한국생물공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.754-754
• /
• 2005

• Bulletin of the Korean Chemical Society
• /
• v.35 no.12
• /
• pp.3425-3426
• /
• 2014

• Journal of the Korea Concrete Institute
• /
• v.13 no.5
• /
• pp.507-515
• /
• 2001

Significant improvements in bond strength between new and existing concrete can be achieved through the modification of the new concrete by latex. This study focuses on the investigation of bond strength of latex modified concrete. Pull-out bond test and uniaxial direct tensile bond test are adopted for evaluating the adhesion characteristics of latex modified concrete to conventional concrete substrate. The main experimental variables are test methods, latex-cement ratio, surface preparations and moisture levels. The results are as follows; The increase of latex-cement ratio substantially improves the adhesion between latex modified concrete and substrate. The effects of surface preparation at substrate into the bonding of latex modified concrete are quite different according to the conditions of surfaces. Thus, an adequate surface preparations are essential for good bond strength. Because the moisture level of the substrate may be critical to achieving bond, optimum moisture condition for a conventional concrete has evaluated in this study. The saturated condition of surface is the most appropriate moisture level among the considered, followed by dry condition and wet condition.

• Journal of the Korea Concrete Institute
• /
• v.13 no.4
• /
• pp.406-413
• /
• 2001

Up to this day, reinforced spun concrete pipes have been widely used as drain pipes. However, many reinforced spun concrete pipes are exposed to the deteriorated environment such as freezing-thawing damage and chemical attack by the growth of a sulfur-oxidizing bacterium isolated from corroded concrete. The purpose of this study is to evaluate the effects of lining by polymer-modified mortar using polymer dispersions as cement modifier on the development in durability of reinforced spun concrete pipe. The polymer-modified mortars were prepared with various polymer types and polymer-cement ratios, and tested for compressive and flexural strengths, acid, freezing-thawing, and heat resistances. And then, the reinforced spun concrete pipe product lined by polymer-modified mortars was tested for adhesion in tension and surface conditions according to curing temperatures in the field. From the test results, it is apparent that the polymer-modified mortars have good mechanical properties and durability as a lining material. In practice, all polymers can be used as lining the materials for reinforced spun concrete pipe, and types of polymer, and polymer-cement ratio and curing conditions are controlled for a good lining product.

• Journal of Adhesion and Interface
• /
• v.19 no.1
• /
• pp.1-4
• /
• 2018

Water In this study, CR/silica nanocomposites were produced by dispersing nanosilica on chloroprene rubber (CR) to apply toluene-free primers for mobile devices. The properties of the modified chloroprene rubber using nanosilica was evaluated through FT-IR, SEM, EDS, Contact angle. The SEM images indicated that P-4 (4 phr) was the most homogenously dispersed. Pencil hardness measurements and Contact angle indicated that the hardness of the CR/silica nanocomposite and the hydrophobicity increased with increase in the silica content. The peel strength of P-4 (4phr) was the highest and the initial peel strength of P-4 sample (2.9 kgf/inch) was 50% higher than that of the P-0 sample.

• Journal of the Korean Ceramic Society
• /
• v.44 no.9
• /
• pp.496-501
• /
• 2007

The properties of the polymer-modified mortars are influenced by the polymer film, cement hydrates and the combined structure between the organic and inorganic phases. Also, this quality of polymer modified cement strongly depend on weather condition. To overcome this problem, polymer-modified cement based on rapid setting cement mortars were prepared by varying polymer/cement mass ratio (P/C) with a constant water/cement mass ratio of 0.5. The effect of polymer on the hydration of this polymer cement is studied on different curing temperature. The results showed that the polymer mortar which is modified with rapid setting cement have superior physical strength properties on independent curing temperature. In addition the PIC ratio, the compressive strength, flexural strength, tensile strength and adhesion strength of mortar is enhances and polymer-modified cement based on rapid setting cement is more beneficial to the improvement of the mortar properties in jobsite.