• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1996년도 한국자동제어학술회의논문집(국내학술편); 포항공과대학교, 포항; 24-26 Oct. 1996
• /
• pp.1004-1007
• /
• 1996

Various auto-tuning methods using relay feedback are presented recently. They are composed of the consecutive procedures identifying Nyquist critical point using relay feedback and designing PID controller by one point of Nyquist plot mapping. This paper suggests a strategy to get the knowledges of Nyquist critical point and the neighborhood point of it using relay feedback. The parameters of PID controller are established by dominant pole approximation based on these knowledges. Designers can make use of the damping ratio as a time domain specification. So design flexibilities are taken in view of stability and performance of the system response considering practical system condition.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.229-229
• /
• 2000

Conventional gain-tuning methods such as Ziegler-Nickels methods, have many disadvantages that optimal control ler gain should be tuned manually. In this paper, modified PID controllers which include self-tuning characteristics are proposed. Proposed controllers automatically tune the PID gains in on-1ine using neural networks. A new learning scheme was proposed for improving learning speed in neural networks and satisfying the real time condition. In this paper, using a nonlinear mapping capability of neural networks, we derive a tuning method of PID controller based on a Back propagation(BP)method of multilayered neural networks. Simulated and experimental results show that the proposed method can give the appropriate parameters of PID controller when it is implemented to DC Motor.

• Journal of Power Electronics
• /
• 제17권3호
• /
• pp.610-620
• /
• 2017

The Finite Control Set-Model Predictive Controller (FCS-MPC) for quasi Z-Source Inverters (qZSIs) is designed to reduce the number of sensors by proposing a current observer for the inductor current. Unlike the traditional FCS-MPC algorithm, the proposed model removes the inductor current sensor and observes the inductor current value based on the deposited prior optimized state as well as the capacitor voltage during this state. The proposed observer has been validated versus a typical MPC. Then, a comparative study between the proposed Modified Finite Control Set-Model Predictive Controller (MFCS-MPC) and a linear PID controller is provided under the same operating conditions. This study demonstrates that the dynamic response of the control objectives by MFCS-MPC is faster than that of the PID. On the other hand, the PID controller has a lower Total Harmonic Distortion (THD) when compared to the MFCS-MPC at the same average switching. Experimental results validate both methods using a DSP F28335.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1991년도 한국자동제어학술회의논문집(국제학술편); KOEX, Seoul; 22-24 Oct. 1991
• /
• pp.1671-1676
• /
• 1991

Direct digital design of computed torque controllers for a robot manipulator is discussed in this paper. A simple discrete-time model of the robot manipulator obtained by Euler's method is used for the design. Taking account of computation delay in the digital processor, we propose predictor-based designs of the PD and PID type controllers. The PID type controller is designed based on a modified version of the discrete-time integral controller proposed by Mita. For both controllers, the same formulas can be used to determine the feedback gains. A simulation example is presented to compare the robustness of the proposed controllers against physical parameter variations.

• 제어로봇시스템학회논문지
• /
• 제12권5호
• /
• pp.425-430
• /
• 2006

To meet an increasing demand for high performance in gun dynamic plant, both a precise and a fast response positioning are strongly required for the gun servo system. A mode switching control(MSC) scheme, which includes a fine stabilizing controller, fast positioning one and a switching function, is widely used to meet this requirement. Stabilization is performed through PID controller, while a time optimal control method is used for target designation. In this paper, a modified PTOS(Proximate Time Optimal Servomechanism) algorithm is derived so as to accommodate the damping term in the gun plant model. Also, applying a mode switching strategy, the bumpless transfer is made possible when the controller switches from PTOS to PID. To show the effectiveness of the overall control system, simulation results are given including the gun dynamics.

• 한국지능시스템학회:학술대회논문집
• /
• 한국퍼지및지능시스템학회 1998년도 춘계학술대회 학술발표 논문집
• /
• pp.43-46
• /
• 1998

This paper presents a new parameter tuning method for PID controller. The Ziegler-Nichols Parameter tuning has been widely known as a fairly heuristic method to good determine setting of PID controllers, for a wide range of common industrial processes It has a excessive overshoot in the set point response, set point weighting can reduced the overshoot to specified values. It will also be shown that set point weighting is superior to the conventional solution of reducing large overshoot by other method. In this paper, we will modified the Ziegler-Nichols tuning formula by fuzzy set. These method will give appreciable improvement in the performance of PID controllers.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1998년도 하계학술대회 논문집 B
• /
• pp.775-777
• /
• 1998

The Ziegler-Nichols parameter tuning has been widely known as a fairly heuristic method to good determine setting of PID controllers, for a wide range of common industrial processes. We extract process knowledge required for rule base controller through tuning experiment and simulation study, such as set point weighting and normalised gain and dead time of process. In this paper, we presents a rule base PID controller by extracted process knowledge and the modified Ziegler-Nichols tuning. Computer simulation are provided demonstrate the feasibility of this approach.

• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.106-113
• /
• 1997

A new algorithm based upon TDC (Time Delay Control) is proposed to improve the robustness of TDC performance in systems where the stick-slip friction is strong. Experiments were performed at the different levels of friction. The reponses of the TDC and the modified TDC were compared each other, and against those of a PID controller with an anti-windup. The results show that the TDC and the modified TDC equally perform better than the PID, and that the modified TDC performs consistently well even with variations in the friction level while the TDC does not.

• Journal of Power Electronics
• /
• 제15권2호
• /
• pp.346-355
• /
• 2015

On the basis of the conventional PID control algorithm, a modified adaptive PID (MA-PID) control algorithm is presented to improve the steady-state and dynamic performance of closed-loop systems. The proposed method has a straightforward structure without excessively increasing the complexity and cost. It can adaptively adjust the values of the control parameters ($K_p$, $K_i$ and $K_d$) by following a new control law. Simulation results show that the line transient response of the MA-PID is better than that of the adaptive digital PID because the differential coefficient $K_d$ is introduced to changes. In addition, experimental results based on a FPGA indicate that the MA-PID control algorithm reduces the recovery time by 62.5% in response to a 1V line transient, 50% in response to a 500mA load transient, and 23.6% in response to a steady-state deviation, when compared with the conventional PID control algorithm.

• 융합신호처리학회논문지
• /
• 제4권4호
• /
• pp.52-57
• /
• 2003

PID제어기의 파라미터의 조정 방법이 전문가의 경험적 지식과 플랜트 스텝응답 파형 모양에 기초하여 퍼지 싱글톤 추론에 의해 행하는 방법을 나타내었다. 파라미터 조정방법은 두 레벨이 있다. 높은 레벨은 모델링 할 수 없는 플랜트 특성에 대하여 전문가의 Know-how에 기초하여 제어기의 수정계수를 결정하는 것이다. 저 단계는 Ziegler-Nichol 의 한계 감도법의 응답 특성에 의해 특정 계수를 결정한다. 마지막 단계는 량과 제어응답 파형의 면적법에서 얻은 특정량에서 조정 규칙으로 취하고 퍼지추론에 수정 계수와 특정계수로 조정규칙을 만들어 퍼지 싱글톤 추론에 의해 PID제어기의 각 파라미터를 적정한 값으로 자동조정 하는 법을 나타내었다.