• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.11a
• /
• pp.647-650
• /
• 2004

The modeling of an active vibration isolation system is accomplished by using the equivalent spring constant, mass and rotational Inertia of each component. The detailed model of the actuation module is successful for describing its frequency-domain performance but also too complicated to implement it to actual system for control so that the order of the model is reduced up to the degree that preserves its characteristic in the low frequency range. The reduced model is suitable for identifying the unknown system parameters such as damping constants of components. The overall isolation system is described by using the reduced model of the actuation module. The accurate model ing and system parameter identification that is essential for the control of the active vibration isolation system is attained successfully.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.41 no.8
• /
• pp.537-544
• /
• 2017

The purpose of this study is to analyze the flow characteristics when a staggered hollow fiber membrane module is modeled as a porous medium. The pressure-velocity equation was used for modeling the porous medium, using pressure drop data. In terms of flow characteristics, we compared the case of the "porous medium" when the membrane module was modeled as a porous medium with the case of the "membrane module" when considering the original shape of the membrane module. The difference in pressure drop between the "porous medium" and "membrane module" was less than 0.6%. However, the maximum flow velocity and mean turbulent kinetic energy of the "porous medium" were 2.5 and 95 times larger than those of the "membrane module," respectively. Our results indicate that modeling the hollow fiber module as a porous medium is useful for predicting pressure drop, but not sufficient for predicting the maximum flow velocity and mean turbulent kinetic energy.

• Phonetics and Speech Sciences
• /
• v.10 no.1
• /
• pp.39-48
• /
• 2018

A typical statistical parametric speech synthesis (text-to-speech, TTS) system consists of separate modules, such as a text analysis module, an acoustic modeling module, and a speech synthesis module. This causes two problems: 1) expert knowledge of each module is required, and 2) errors generated in each module accumulate passing through each module. An end-to-end TTS system could avoid such problems by synthesizing voice signals directly from an input string. In this study, we implemented an end-to-end Korean TTS system using Google's Tacotron, which is an end-to-end TTS system based on a sequence-to-sequence model with attention mechanism. We used 4392 utterances spoken by a Korean female speaker, an amount that corresponds to 37% of the dataset Google used for training Tacotron. Our system obtained mean opinion score (MOS) 2.98 and degradation mean opinion score (DMOS) 3.25. We will discuss the factors which affected training of the system. Experiments demonstrate that the post-processing network needs to be designed considering output language and input characters and that according to the amount of training data, the maximum value of n for n-grams modeled by the encoder should be small enough.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.54 no.5
• /
• pp.185-189
• /
• 2005

This paper focuses on the design for Rx/Tx switch module of GSM(global standard mobile) band, characterization of a miniature, low power and dual-band implementation of the front-end switch module with low-pass filer And the effort to make agreement between the simulated design and the measured data for these solutions takes the place through accumulated design and manufacturing data library. We present the design, modeling and measurement of switch module integrating GSM Rx/Tx switching circuit and LPF(low pass filter) on a LTCC(low temperature co-fired ceramic) substrate. For GSM application, insertion and return loss of the low pass filter designed was less than 0.3 dB which was less than 12.7 dB at 900 MHz. The LTCC switch module contained 10 embedded passives and 3 surface mount components integrated on 4.6$\times$4.8$\times$1.2 mm, 6-layer multi-layer integrated circuit. The insertion loss of switch module measured at 900 MHz was 11 dB. In both of the design approach yielded excellent agreement between measured and simulated results.

• Korean Journal of Computational Design and Engineering
• /
• v.7 no.1
• /
• pp.9-17
• /
• 2002

The study is insufficient on process planning of the elliptical deep drawing product. Thus, in this present study, the expert system for elliptical deep drawing products was constructed by using process sequence design. The expert system was developed to be based on the general concept of each entity. The system was developed in this work consists of sixth modules. The first one is a shape recognition module to recognize non-axisymmetric products and to generate Entity_list. The second one is three dimensional (3-D) modeling module to calculate the surface area for non-axisymmetric products. The third one is a blank design module to create suggested blanks of three shapes with the identical surface area. The fourth one is shape design module based on the production rules that play the most important role in an expert system for manufacturing. The production rules are generated and upgraded by inter- viewing field engineers, plastic theory and experiments. The fifth and sixth ones are a graphic module to visualize results of the expert system and a post module to rise user's convenience, respectively. According to constructed the expert system for process sequence design, it was possible to reduce the lead time.

• Korean Journal of Environmental Agriculture
• /
• v.28 no.2
• /
• pp.113-124
• /
• 2009

Severe sediment-laden problem has been the hot issue in Korea. It was assumed that agricultural activities and landslides were the primary causes of these problems in watersheds. The USLE-based systems have been widely used in soil erosion studies. However the GIS-based USLE modeling system has limitation in USLE L factors. In this study, the SATEEC L module was developed to reflect the slope length segmentations in the fields. The SATEEC L module was applied to the study watershed to analyze the effects of using the SATEEC L module on estimated sediment. As shown in the comparisons between SATEEC estimated sediment with SWAT values, the SATEEC GA-SDR module derives the SDR with reasonably acceptable accuracies. However, it is worthy to note that the soil erosion using the SATEEC L module for the study watershed was lower than that without using the SATEEC L module by 25%, although the SATEEC estimated sediment values with and without using L module match the SWAT sediment values with similar accuracies. This is because the SATEEC GA-SDR module estimates lower SDR in case of greater soil erosion estimation without the L module and greater SDR in case of lower soil erosion estimation with the L module. This indicates that the SATEEC input parameters, especially L factor, need to be prepared with care for accurate estimation of SDR at a watershed scale and for accurate evaluation of BMPs in the watershed.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.785-791
• /
• 2005

Reconfigurability of machine tools is one of the critical factors to realize the responsive manufacturing systems to satisfy the mass-customization production. This paper presents the methods to model and simulate the machine tools on Internet in response to change in the machining requirements. Specifically, a set of module combination rules and a modeling method of the structure of machine tools using connectivity graph are developed. In response to the user requirements, kinematic relations and structures of machine tools can be derived using the module combination rules and connectivity graph relationships. Internet-based simulator of machine tools is implemented and presented. The developed machine tool simulator can be used to verify the structure of machine tools derived from the user requirements.

• Journal of KIBIM
• /
• v.4 no.3
• /
• pp.1-9
• /
• 2014

As BIM application continues to increase in civil engineering, in this study, 3D information model for RC(Reinforced Concrete) bridge pylon was developed and verified its effectiveness at the structural-design stage. To define 3D information model of RC A-Type pylon, characteristics of pylon were analyzed and 3D model structure was constructed. The 3D information model, one of the core product of BIM, manages all information generated during all life-cycle of a structure and consequently maximizes the efficiency of utilizing information. Also, this study proposes interface module between input data in structural analysis and 3D model of RC pylon. The module can create the input data for non-linear structural analysis. It is essential to study on method of developing 3D information model and propose a structural analysis model by utilizing 3D model for the effective use of BIM techniques in construction industry. The results of this study can be used as the base data for developing the 3D information model of RC pylon in the structural analysis field.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.12 no.2
• /
• pp.135-151
• /
• 2014

It is very important to properly understand such "Transport Pathways" elements as "Pipe" and "Cell" pathways in commercial GoldSim Transport Module (GTM) for developing higer quality models and programs for performance assessment of complex radioactive waste repositories. With an illustrative case under an earthquake scenario, by which an increasement in the groundwater flow rate occurs though the geological medium, ways of avoiding possible modeling errors in the nuclide transport modeling in the radioactive waste repository system for its safety assessment by utilizing such pathways are discussed and a proper usage of the pathways is proposed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1604-1618
• /
• 1995

In the process of mechanical assembly design, assembly modeling systems have been used mainly for the design verification before manufacturing by enabling to check the interference and/ or the dynamic and kinematic performance. However, the conventional assembly modeling systems have a shortcoming that they can not be used in the initial design stage but can be used only after the design is fully completed. In other words conventional assembly modeling systems provide bottom-up modeling which means that the detailed modeling of components must precede the definition of relationships between them. To resolve this problem, an assembly modeling system is proposed to provide a top-down modeling environment in which components and assembly can be modeled simultaneously. To this end, an assembly data structure suitable for top-down assembly modeling has been established. Feature positioning Module(FPM) using geometric constraints has been also developed. The Sekective Solving Method proposed for FPM is based on the priority between the constraint equations and enables the designer's intent expressed by geometric constraints to be maintained throughout the whole modeling process. Finally, the feature based modeling technique using two-level features has been developed. Two-level features include an abstract model and a detailed model in a merged form in non-manifold data frame.