• Environmental and Resource Economics Review
• /
• v.10 no.4
• /
• pp.515-545
• /
• 2001

This paper introduces the least absolute deviations estimation of the contingent valuation model, which corresponds to the semi-parametric estimation of discrete choice models by Manski (1975, 1985) and Lee (1992). The least absolute deviations estimation is more robust to mis-specified distributional assumptions in the estimation of the contingent valuation model, compared to the maximum likelihood estimation. The full identification and strong consistency of the estimation are proved and its application to different formats of contingent valuation survey data is discussed. Simulation studies are designed to evaluate its operational characteristics including computational strategies, small sample properties and the efficiency gain of a follow-up question. The bias and efficiency of least absolute deviations and maximum likelihood estimation are compared in the presence of heteroskedasticity.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2014.10a
• /
• pp.687-689
• /
• 2014

This paper deals with the optimal muffler model by using acoustic analysis and CFD(computational fluid dynamics) analysis. The complicated muffler model could be better noise reduction performance. However, it could be worse affected to back-pressure performance by pressure drop in working fluid. High back-pressure is caused to low system efficiency. Therefore, it is important for the muffler design to consider the pressure drop. The muffler models are changed their partition plate position. Acoustic power transmission loss(TL) and pressure drop of working fluid are calculated by using computational analysis and used to build database for finding their trends. The optimal muffler model in user-interested frequency range could be selected by analyzing this database.

• 한국해양학회지
• /
• v.28 no.2
• /
• pp.121-131
• /
• 1993

The tidal front forming in the Mid-Yellow Sea off Korea, near Tae-An peninsular, is calculated using a 3-D general circulation model(Semtner, 1974) and the concept of mixing rate, an extension of the concept of mixing efficiency proposed by simpson & Hunter(1974). Along the north and south open boundaries, simple radiation conditions are applied. The model is run with the initial state which represents the winter condition. With imposed uniform heating by solar radiation and spatially-different vertical mixing, the model then generated the tidal front comparable to the observed one.

• The Journal of Information Systems
• /
• v.12 no.1
• /
• pp.47-66
• /
• 2003

This study was examined the relationship between the exogenous and endogenous variables in our model to measure ERP system performance using path analysis. The exogenous variables are system quality, user participation, user training, top management support and self-efficacy, and the endogenous variables are system usage, user satisfaction, and work efficiency. The results of the study are shown as follows. First, all the exogenous variables in our model have a direct effect on user satisfaction, and system quality, training, and self-efficacy have a direct effect on system usage. Second, system usage has a direct effect on user satisfaction and user satisfaction has a direct effect on work efficiency. The findings show that the exogenous variables in the model are important to increase ERP implementation success.

• Journal of Ocean Engineering and Technology
• /
• v.18 no.1
• /
• pp.1-6
• /
• 2004

In this paper, the performance of a wave absorbing system using an inclined punching plate, was investigated. Using the multi-domain boundary element method (BEM), the reflection coefficients of an inclined punching plate were tested with various design parameters, such as inclined angle, porosity, and wave frequencies. To confirm the numerical solutions, the systematic model test was conducted at 2-D tank and square tank. The numerical results were in good agreement with the experimental results within the entire frequency range. It was found that an inclined punching plate had an excellent wave absorbing efficiency, compared to a horizontal one. Also, the optimal range of an inclined angle had an excellent wave absorbing efficiency, compared to a horizontal one the optimal range of the inclined angle is 10°<β<20°. The developed wave absorber was installed at KRISO's square basin, and is working effectively for various model tests.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.57 no.12
• /
• pp.2285-2290
• /
• 2008

Even though efficiency of coal-fired power plant is proportional to operating temperature, increasement of operating temperature is limited by a technological level of each power plant component. It is an alternative plan to increase operating pressure up to ultra super critical point for efficiency enhancement. It is difficult to control process of power plant in ultra super critical point because that point has highly nonlinear characteristics. In this paper, new control logic, Unit Response Optimizer Controller(URO Controller) which is based on Fuzzy logic and Model Predictive Controller, is introduced for better performance. Then its performance is tested and analyzed with design guideline.

• Geomechanics and Engineering
• /
• v.11 no.5
• /
• pp.691-711
• /
• 2016

In this study, the uplift capacity of anchor plates embedded in sand was investigated by conducting model tests. Square shaped anchors were used in the tests and parameters such as relative density of sand, embedment ratio (H/B), spacing ratio between anchors (S/B) and anchor configuration affecting the uplift capacity were investigated. Breakout factor and group efficiency which are dimensionless parameters were used to show the results. A series of finite element analyses and analytical solutions were additionally performed to ascertain the validity of the findings from the laboratory model tests and to supplement the results of the model tests. It can be concluded that the embedment depth in dense sand soil condition is the most important parameter with respect to the other parameters as to influencing the uplift capacity of group anchors.

• Smart Structures and Systems
• /
• v.21 no.2
• /
• pp.225-234
• /
• 2018

E-Health allows you to supersede the central patient wireless healthcare system. Wireless Body Sensor Network (WBSN) is the first phase of the e-Health system. In this paper, we aim to understand e-Health architecture and configuration, and attempt to minimize energy consumption and latency in transmission routing protocols during restrictive latency in data delivery of WBSN phase. The goal is to concentrate on polling protocol to improve and optimize the routing time interval and schedule communication to reduce energy utilization. In this research, two types of network models routing protocols are proposed - elemental and clustering. The elemental model improves efficiency by using a polling protocol, and the clustering model is the extension of the elemental model that Destruct Supervised Decision Tree (DSDT) algorithm has been proposed to solve the time interval conflict transmission. The simulation study verifies that the proposed models deliver better performance than the existing BSN protocol for WBSN.

• Journal of the Korean Solar Energy Society
• /
• v.21 no.1
• /
• pp.27-31
• /
• 2001

The Kaplan turbine model has been tested and analized. The blade angle and the guide vane opening of the turbine model were designed to be varied according to the best combination of guide vane and runner blade opening. When the changes in head and output were comparatively large, the efficiency drop were small, so the efficiency characteristics and stability of the entire operating condition were maintained in good condition. These results showed that the developed model in this study will be suitable for small hydro power stations with large changes in head and load.

• Transactions of the Korean hydrogen and new energy society
• /
• v.14 no.2
• /
• pp.171-176
• /
• 2003

The propeller type hydro turbine model with vertical axis has been tested and analyzed. The blade angle of turbine model were designed to be varied according to the condition of head and flowrate. When the changes in head and output were comparatively large, the efficiency drop were small, so the efficiency characteristics and stability of the entire operating condition were maintained in good condition. These results showed that the developed model in this study will be suitable for small hydro power stations with large changes in head and load such as sewage treatment plants and agricultural reservoirs.