• The Journal of the Korea institute of electronic communication sciences
• /
• v.6 no.3
• /
• pp.397-404
• /
• 2011

In this research, wish to suggest method to embody system that can accommodate defect of PLC and find actual propriety. Defect permission control system minimizes production damage because enables repair and checking without discontinuance and improve believability about whole system. Propose duplexing of system to embody this fault tolerant system. Therefore, composed control system that can permit defect or breakdown duplexings of various module proposing this system, and confirms to simulation and actuality kiln of defect permission control system through an application experiment, and compares for mean time between defect by estimate and defect special quality and system configuration of failure(failure) to improve believability of PLC control system together. In proposed system expression method and system mode and relation with operation mode, error discovery mode and switching tube of duplexing mode, and PLC's central processing unit of node study algorithm about master-standby conversion driving and continuous operation of 2 channels method that have 2 that is not one and deduced continuous operation method and result about defect permission in this algorithm and applies this result to actuality kiln control system and confirms continuous operation about PLC defect permission.

• Journal of Advanced Navigation Technology
• /
• v.17 no.5
• /
• pp.497-505
• /
• 2013

In TETRA(TErrestrial Trunked RAdio) standard, TMO(Trunked Mode Operation) communicates with the UE through the base station and it has a higher priority than DMO(Direct Mode Operation) which communicates with UE directly for channel allocation. As a result, the UE needs an algorithm which restricts the frequency allocation by TMO so that DMO can have a successful communication within the network. However, the TETRA DMO standard does not consider this issue. In this paper, we propose an active DMO channel selection algorithm which allocates a channel based on some additional information such as channel usage state of TMO and channel utilization of DMO. The experimental results show that the proposed algorithm outperforms existing DMO channel allocation scheme in terms of the transmission efficiency.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.2 no.6
• /
• pp.9-17
• /
• 1994

In this study, a shifting algorithm of CVT was suggested for the two(2) driving modes : (1) power mode and (2) economy mode. Shifting algorithm must be obtained to make the engine run on the optimum operating line for the desired performance of the vehicle. Optimum operating lines of the engine were obtained by connecting the shortest way of the iso-power lines for the power mode and by connecting the shortest way of the BSFC curves for the economy mode. Also dynamic model of CVT vehicle was derived considering the throttle and the brake operation. By using the shifting algorithm and the CVT vehicle model, numerical simulations were performed to estimate the performance of CVT. Simulation results showed that comparing the performance of the conventional 4-speed automatic transmission, acceleration performance of the CVT vehicle was almost same with the AT vehicle for the power mode and the fuel economy of CVT was 14% superior than that of AT for the economy mode.

• Journal of Power Electronics
• /
• v.19 no.6
• /
• pp.1582-1590
• /
• 2019

A new method for reducing the common-mode current generated by the voltage variations in a two-inverter air conditioner system by applying a synchronized pulse-width modulation (PWM) strategy is proposed. The PWM signals of the master-mode inverter are generated based on the reference voltage, while those of the slave-mode inverter are output in the opposite direction when the master-mode inverter changes its switching state. However, the slave-mode control results in a mismatch between the reference voltage and the actual output voltage that is modified by synchronized control operation. The proposed method is capable of reducing and controlling this voltage error by performing signal selection in the vector space of the slave-mode inverter, which mitigates the distortion of the phase current. The efficacy of this method in reducing conducted emissions has been validated both theoretically and experimentally.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.233-241
• /
• 2018

This paper describes a lightweight implementation of a cryptographic processor supporting GCM (Galois/Counter Mode) authenticated encryption (AE) that is based on the two block cipher algorithms of ARIA and AES. It also provides five modes of operation (ECB, CBC, OFB, CFB, CTR) for confidentiality as well as the key lengths of 128-bit and 256-bit. The ARIA and AES are integrated into a single hardware structure, which is based on their algorithm characteristics, and a $128{\times}12-b$ partially parallel GF (Galois field) multiplier is adopted to efficiently perform concurrent processing of CTR encryption and GHASH operation to achieve overall performance optimization. The hardware operation of the ARIA/AES-GCM AE processor was verified by FPGA implementation, and it occupied 60,800 gate equivalents (GEs) with a 180 nm CMOS cell library. The estimated throughput with the maximum clock frequency of 95 MHz are 1,105 Mbps and 810 Mbps in AES mode, 935 Mbps and 715 Mbps in ARIA mode, and 138~184 Mbps in GCM AE mode according to the key length.

• Journal of Mechanical Science and Technology
• /
• v.15 no.3
• /
• pp.339-350
• /
• 2001

To overcome problems in tracking error related to the unmodeled dynamics in the high speed operation of industrial robots, many researchers have used sliding mode control, which is robust against parameter variations and payload changes. However, these algorithms cannot reduce the inherent chattering which is caused by excessive switching inputs around the sliding surface. This study proposes a fuzzy-sliding mode control algorithm to reduce the chattering of the sliding mode control by fuzzy rules within a pre-determined dead zone. Trajectory tracking simulations and experiments show that chattering can be reduced prominently by the fuzzy-sliding mode control algorithm compared to a sliding mode control with two dead zones, and the proposed control algorithm is robust to changes in payload. The proposed control algorithm is implemented to the SCARA (selected compliance articulated robot assembly) robot using a DSP (digital signal processor) for high speed calculations.

• Current Optics and Photonics
• /
• v.2 no.5
• /
• pp.413-421
• /
• 2018

We propose a novel methodology based on the multiplication function to improve the signal-to-noise ratio (SNR) for vibration detection in a phi optical time-domain reflectometer system (phi-OTDR). The extreme-mean complementary empirical mode decomposition (ECEMD) is designed to break down the original signal into a set of inherent mode functions (IMFs). The multiplication function in terms of selected IMFs is used to determine a vibration's position. By this method, the SNR of a phi-OTDR system is enhanced by several orders of magnitude. Simulations and experiments applying the method to real data prove the validity of the proposed approach.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.51 no.6
• /
• pp.260-264
• /
• 2002

We developed LD Pumped Nd:$VVO_4$ microchip laser with the cavity length of 1mm. The microchip laser output was 87.5㎽ at the wavelength of 1063.9nm with the input power of 241㎽ at the wavelength of 809nm. The slope efficiency was 40.7% and the threshold input power was 31.1㎽. We have also defined input power limit for the single longitudinal mode operation theoretically. It was 2.5 times larger than that of threshold input intensity. According to the results of simulation, the Nd:YVO$_4$ microchip laser can be operated with the maximum output of 15㎽ for the single longitudinal mode up to the input power of 77.75㎽.

• Journal of the Optical Society of Korea
• /
• v.12 no.4
• /
• pp.326-336
• /
• 2008

A WDM-PON has been considered as an ultimate solution for access networks. However, there were many technical and practical issues for commercial deployment. These issues were solved with wavelength locked F-P LD and the WDM-PONs employing this optical source were commercialized. These WDM-PON systems have been deployed in Korea, Europe, and US. We reviewed wavelength locking technology and WDM-PON achievements. When we inject spectrum sliced broadband light into an F-P LD, the multimode output is changed to a quasi single mode. Then, we can use the single mode light for WDM signal transmission. The broad spectral gain of the semiconductor gain medium enables a color-free operation of WDM-PON, i.e., an identical ONT can be used for each user. The wavelength locking properties depend on many parameters, especially alignment of injection wavelength to a lasing mode, passband profile of AWG and front facet reflectivity of F-P LD. However, these dependencies can be reduced by proper design of the laser and the injection bandwidth. Thus, WDM-PON systems have been achieved with color-free operation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.40 no.12
• /
• pp.31-38
• /
• 2003

In this paper, we proposed a new structural AGC(Automatic Gain Control) circuit with extremely short settling time using high speed operation characteristics of a clipper. We investigated its operation characteristics in analysis. We also designed a burst-mode preamplifier for 1.25Gbps EPON systems using commercial foundry and investigated its characteristics by comparing the results of the designed and those of the analyzed. The characteristics of the designed circuit are in good agreement with those of the analyzed. As a result, it is shown that it is possible to realize extremely short settling time of under 1㎱.