• Proceedings of the Korean Nuclear Society Conference
• /
• 2001.10a
• /
• pp.262.1-262
• /
• 2001

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.23 no.6 s.165
• /
• pp.1039-1047
• /
• 1999

It is necessary to evaluate the fatigue behavior of rail steel under the multi-axial stress state to assure the railway vehicle's safety. For this purpose, the stress analysis to investigate the crack initiation criteria, static failure and fatigue behavior under mixed-mode are performed. The stress analysis results show that the initiation of the transverse fissure depends on the maximum shear stress below the surface. For the mixed mode, the fatigue crack growth behavior which is represented by the projection crack length and comparative S.I.F, ${\Delta}K_v$, shows the more conservative results. Also, its rate is lower than that of the case of the mode I, and this difference decreases with increasing the stress ratio, R.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.14 no.4
• /
• pp.761-769
• /
• 1994

Actual load acting on rail surface in the track is the combined mode loading due to the contact rolling load of the wheels. To investigate the fracture behavior on rail steel under combined modes I and II, fracture tests were performed by using the test jigs and fracture specimen which were designed by Richard. The analysis results of experimental fracture data were compared with various fracture criteria that have been introduced for determination of the crack propagation direction and the critical stress of fracture of a crack submitted to a mixed mode loading. From the results, it was shown that the actual crack propagation direction of rail steel agree with the crack propagation directions predicted by maximum tangential stress criterion and strain energy density criterion, and that fracture criterion follows principal strain criterion.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.31 no.5
• /
• pp.57-72
• /
• 1999

Traditional theories of the tensile failure of paper have assumed that uniform strain progresses throughout the sheet until an imperfection within the structure causes a catastrophic break. The resistance to tensile elongation is assumed to be elastic , at first, throughout the structure, followed by an overall plastic yield. However, linear image strain analysis (LISA) has demonstrated that the yield in tensile loading of paper is quite non-uniform throughout the structure, Traditional theories have failed to define the flaws that trigger catastrophic failure. It was assumed that a shive or perhaps a low basis weight area filled that role. Studies of the fracture mechanics of paper have typically utilized a well-defined flaw around which yield and failure could be examined . The flaw was a simple razor cut normal to the direction of tensile loading. Such testing is labeled mode I analysis. The included fla in the paper was always normal to the tensile loading direction, never at another orientation . However, shives or low basis weight zones are likely to be at random angular orientations in the sheet. The effects of angular flaws within the tensile test were examined. The strain energy density theory and experimental work demonstrate the change in crack propagation from mode I to mode IIas the initial flaw angle of crack propagation as a function of the initial flaw angle is predicted and experimentally demonstrated.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.24 no.4 s.175
• /
• pp.982-990
• /
• 2000

The finite element alternating method is extended further for general three dimensional cracks in an isotropic body subjected to the mode I loading. The required analytical solution for a dime dimensional crack in an infinite isotropic body is obtained by solving the integral equations. In order to remove the high singularity in integration, the technique suggested by Keat et al. was used. With the proposed method several example problems are solved in order to check the accuracy and efficiency of the method.

• Journal of Mechanical Science and Technology
• /
• v.14 no.9
• /
• pp.978-984
• /
• 2000

The aim of this study is to investigate the ductile fracture behaviour under Mode I loading using SA533B pressure vessel steel. Experiments consist of the Round Notch Bar Test (RNB), Single Edge Crack Bending Test (SECB), and V-Notch Bar Test (VNB). Results from the RNB test were used to tune the damage modelling constant. The other tests were performed to acquire the J-resistance curves and to confirm the damage constants. Microstructural observation includes the measurement of crack profile to obtain the roughness parameter. Finally, simulation using Rousellier Ductile Damage Theory (RDDT) was carried out with 4-node quadrilateral element ($L_c=0.25\;mm$). For the crack advance, the failed element removal technique was adopted with a ${\beta}$ criterion. In conclusion, the predicted simulation using RDDT showed a good agreement with the experimental results. A trial using a roughness parameter was made for a new evaluation of J-resistance curve, which is more conservative than the conventional one.

• Computers and Concrete
• /
• v.13 no.4
• /
• pp.569-585
• /
• 2014

In this paper, a four-layer road structure consisting of an edge transverse crack is simulated using three-dimensional finite element method in order to capture the influence of a single-axle wheel load on the crack propagation through the asphalt concrete layer. Different positions of the vehicular load relative to the cracked area are considered in the analyses. Linear elastic fracture mechanics (LEFM) is used for investigating the effect of the traffic load on the behavior of a crack propagating within the asphalt concrete. The results obtained show that the crack front experiences all three modes of deformation i.e., mode I, mode II and mode III, and the corresponding stress intensity factors are highly affected by the crack geometry and the vehicle position. The results also show that for many loading situations, the contribution of shear deformation (due to mode II and mode III loading) is considerable.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.16 no.12
• /
• pp.2226-2240
• /
• 1992

This paper studies the applicability of the method of caustics into anisotropic materials under mode I and mixed static loading conditions and introduces the procedure to obtain stress intensity factors(S.I.F.) in anisotropic materials by the method of caustics. The mapping equations for initial and caustic curves in anisotropic materials were introduced and their computer graphical images were compared to the experimental ones to check the validity of the mapping equations proposed in this paper. The agreement between them was found to satisfactory. Two kinds of method to determine S.I.F. in anisotropic materials by the method of caustics were proposed in this paper and applied into the orthotropic materials under various loading conditions. In the case of mode I loading condition, the S.I.F.'s obtained by this paper's methods were found to be quite similar to the results by other method, boundary element method(B.E.M) and in the case of mixed loading condtion, the S.I.F's by this paper and B.E.M. showed a little differences(2.2-24.4%) with respect to the slanted angle of crack.

• Structural Engineering and Mechanics
• /
• v.65 no.6
• /
• pp.699-706
• /
• 2018

In the present contribution, fracture resistance of U-notched GPPS members under mixed mode I/III loading conditions is assessed by using the Averaged Strain Energy Density (ASED) criterion. This criterion has been founded based on the ASED parameter averaged over a well-defined control volume embracing the notch edge. The validation of the theoretical criterion predictions is evaluated through comparing with the results of a series of mixed mode I/III fracture tests conducted on rectangular-shaped GPPS specimens weakened by a single edge U-notch. A recently developed apparatus for mixed mode I/III fracture experiments is employed for measuring the fracture loads of the specimens. The test samples are fabricated with different notch tip radii with the aim of evaluating the influence of this major feature of the U-notched components on the mixed mode I/III fracture behavior. It is shown that the onset of brittle fracture in U-notched GPPS specimens under various combinations of tension and out-of-plane shear can well be predicted by means of the ASED criterion.

• Journal of the Korean Society of Safety
• /
• v.14 no.4
• /
• pp.28-36
• /
• 1999

In this paper, A circular arc crackered plate in biaxially stretched sheets was investigated in the boundary element method. The applications of fracture mechanics have traditionally concentrated on crack problems under an mode I, straight crack. However, many service failures occur from growth of cracks subjected to mixed mode loadings. A rectangular plate with arc crack or slanted central crack, under biaxial tensile loading, was treated analytically and also solved numerically. The Results from BEM applying different loading conditions, crack length (a/W), arc angle($\alpha$) are presented and discussed. The stress intensity factors are evaluated by the techniques of the J-integral. The decomposition method, used to decouple the stress intensity factors in mixed mode problems, is implemented by a considering a small circular contour path around each crack tip. The BIE method was successfully applied to a circular arc crackerd plate problem, also slanted centre cracked plate under mixed mode.