• 한국초전도ㆍ저온공학회논문지
• /
• 제17권3호
• /
• pp.33-36
• /
• 2015

A liquid nitrogen ($LN_2$) is usually used to be a coolant and insulant for a HTS coil system. HTS wires for a superconducting apparatus may be surrounded by gaseous nitrogen ($GN_2$) due to film boiling generated by a quench or voids occurred by electrical breakdown. The increased maximum electric field intensity at $GN_2$ may result in the degradation of dielectric strength of a HTS coil system. In this paper, a study on the dielectric characteristics of a composite insulation system composed of $LN_2$ and $GN_2$ is performed. A sphere-to-plane electrode system made with stainless steel is used to perform the experiments under AC and lightning impulse voltage condition. A sphere electrode is surrounded by $GN_2$ and a plane electrode is immersed into $LN_2$ to conduct dielectric experiments with a composite insulation system. The dielectric experiments are performed according to the level of $LN_2$ from the plane electrode to a sphere electrode. It is found that the dielectric characteristics of a composite insulation system are dependent on the level of $LN_2$ and the field utilization factor of an electrode system.

• Archives of Reconstructive Microsurgery
• /
• 제20권1호
• /
• pp.38-42
• /
• 2011

Purpose: To evaluate the effect of intermittent bleeding method in the distal phalanx replantation. Materials and Methods: From January 2007 through June 2009, authors have replanted 117 cases of distal phalangeal amputation in adults at Soo Hospital and Chonbuk National University Hospital. Cases of zone II were 60 cases and zone III 57 according to Allen classification. Male to female ratio was 8.7:1.3. The most common cause was machinery injury in the factory, 98 cases(83.8%), next one was belt injury of the machine, 11 cases(9.4%) and others, 8(6.8%). At least one digital artery and digital nerve were anastomosed under the operating microscope, but vein was impossible to anastomosis as unable to find out in the zone II and III. After anastomosis of one or more digital arteries and nerves, heparine(6,000-10,000 units) was kept to intravenous injection for 24 hours and at the same time fish mouth incision in 2-3 millimeter diameter was made in the distal radial and ulnar margin of the replanted distal phanlanx. From the first 30 minutes to an hour after replantation, incision site was swabbed with heparinized cotton ball for 5 minutes in every 30 to 40 minutes to make sure perfusion for 24 hours, every an hour at the second day, every two hours at the postoperative third to fifth day. Results: 92 cases(78.6%) was completely survived at average postoperative third week follow-up and satisfied with preservation of the finger nail, digit length, good range of motion of the distal interphalangeal joint and acceptable sensibility at average 1.2 years follow-up. Conclusions: Intermittant bleeding method in replantation of crushed distal phalanx impossible to anastomosis of vein at zone II and III of Allen classification was regarded as one of the notable salvage procedure.

• 대한기계학회논문집B
• /
• 제33권11호
• /
• pp.840-848
• /
• 2009

In the boiling heat transfer mechanism, CHF(critical heat flux) is the significantly important parameter of the system. So, many researchers have been struggling to enhance the CHF of the system in enormous methods. Recently, there were lots of researches about enormous CHF enhancement with the nanofluids. In that, the pool boiling CHF in nanofluids has the significantly increased value compared to that in pure water because of the deposition of the nanoparticle on the heater surface in the nanofluids. The aim of this study is the comparison of the effect of the nanoparticle deposited surface and the modified surface which has the similar morphology and made by MEMS fabrication. The nanoparticle deposited surface has the complex structures in nano-micro scale. Therefore, we fabricated the surfaces which has the similar wettability and coated with the micro size post and nano structure. The experiment is performed in 3 cases : the bare surface with 0.002% water-ZnO nanofluids, the nanoparticle deposited surface with pure water and the new fabricated surface with pure water. The contact angle, a representative parameter of the wettability, of the all 3 cases has the similar value about 0 and the SEM(scanning electron microscope) images of the surfaces show the complex nano-micro structure. From the pool boiling experiment of the each case, the nanoparticle deposited surface with pure water and the fabricated surface with pure water has the almost same CHF value. In other words, the CHF enhancement of the nanoparticle deposited surface is the surface effect. It also shows that the new fabricated surface follows the nanoparticle deposited surface well.

• 전기화학회지
• /
• 제4권3호
• /
• pp.98-103
• /
• 2001

EDLC(electric double layer capacitor)용 활성탄소전극의 제조공정을 dip coating method, doctor blade coating method, paste rolling method로 달리하여 전기화학적 특성과 비축전 용량을 조사하였다. Dip coating method에 의한 전극제조시 전해질염으로 LiPF6를 이용하고 유기용매로 PC-DEC를 이용한 EDLC의 비축전 용량이 130F/g으로 가장 우수하였고, 선형의 시간전압곡선에서의 IR-drop도 0.11V로 작았으며 CV(cyclic voltammetry) 분석 또한 이상적인 EDLC의 특성을 나타내었다.

• 대한치과보철학회지
• /
• 제45권5호
• /
• pp.665-674
• /
• 2007

Purpose: The purpose of this study was to investigate the effect of sire and shape of retention element on the bond strength of indirect composite resin and metal. Material and method: The metal disk specimens, each 6mm in diameter, were cast from CrCo alloy. They were divided into 8 groups by applied retention element. retention bead group $B2\;({\phi}\;0.2mm),\;B4\;({\phi}\;0.4mm),\;B6\;({\phi}\;0.6mm),\;B8\;({\phi}\;0.8mm)$, retention crystal group C2 (0.2mm), C5 (0.5mm), C8 (0.8mm) and sandblasting group SB ($110{\mu}m\;Al_2O_3$ blasting) as control. Eighty-eight metal specimens were veneered with $TESCERA^{(R)}$ Indirect resin system. One specimen of each group was sectioned and the resin-metal bonding pattern at the interface was observed under measuring microscope. Other specimens were then tested for tensile bond strength on an Instron universal testing machine at a crosshead speed of 2mm/min. Results: 1. Compared to sandblasting, beads or crystals increased the resin-metal bond strength (P<.05). 2. 0.2mm retention crystals were most effective in improving the resin-metal bond strength (P>.05). 3. 0.2mm beads showed the highest bond strength among retention bead groups, but there was no statistically significant difference (P>.05). 4. Retention crystals tend to be higher in bond strength than retention beads due to wider surface area. 5. The larger retention element, the larger the undercut for the mechanical retention, but the gap at resin-metal interface was also increased. Conclusion: Within the limitations of this study, 0.2mm retention crystals were most effective in improving the resin-metal bond strength.

• 한국동물위생학회지
• /
• 제30권3호
• /
• pp.353-362
• /
• 2007

A total of 1,354 samples was collected from bovine and porcine carcass from January 2005 to December 2006 in a slaughter house. Twenty five strains(1.8%) of Listeria monocytogenes were isolated from 1,354 samples using selective media. Ten(1.4%) L monocytogenes were isolated from the 677 of bovine carcasses, and 15(2.2%) were isolated from the 677 of porcine carcasses. Among 15 L mono-cytogenes from porcine, 11 siolates were serovars 1/2c, followed by 1/2b (3 strains, 20.0%) and 1/2a(1 strain) Out of 10 bovine samples, positive cases in 1/2a were 9 strains (90.0%), 1/2b were 1 strains(10.0%). PCR primers were selected to amplify a 520-base pair(bp) DNA fragment from the listeolysin O gene (hlyA) of L mono-cytogenes. A 520-bp product was detected in PCR with DNA from L monocytogenes, but not from the other Listeria species tested. A total of 25 L monocytogenes strains were analysed by PFGE after digestion with Apa I. PFGE analysis of genomic DNA showed the $14{\sim}18$ fragments ranging in size from 30 to 550 kb, resulting in 14 patterns.

• 한국전기전자재료학회논문지
• /
• 제16권2호
• /
• pp.102-107
• /
• 2003

This study puts focus on the optimization of growth temperature of CIGS absorber layer which affects severely the performance of solar cells. The CIGS absorber layers were prepared by three-stage co-evaporation of metal elements in the order of In-Ga-Se. The effect of the growth temperature of 1st stage was found not to be so important, and 350$^{\circ}C$ to be the lowest optimum temperature. In the case of growth temperature at 2nd/3rd stage, the optimum temperature was revealed to be 550$^{\circ}C$. The XRD results of CIGS films showed a strong (112) preferred orientation and the Raman spectra of CIGS films showed only the Al mode peak at 173cm$\^$-1/. Scanning electron microscopy results revealed very small grains at 2nd/3rd stage growth temperature of 480$^{\circ}C$. At higher temperatures, the grain size increased together with a reduction in the number of the voids. The optimization of experimental parameters above mentioned, through the repeated fabrication and characterization of unit layers and devices, led to the highest conversion efficiency of 15.4% from CIGS-based thin film solar cell with a structure of Al/ZnO/CdS/CIGS/Mo/glass.

• 한국수자원학회:학술대회논문집
• /
• 한국수자원학회 2023년도 학술발표회
• /
• pp.17-17
• /
• 2023

국내의 부지특성 및 감시 관련 규정은 원자력 안전위원회 고시 제2021-16호 제4조(세부지침)와 원자력 안전위원회 고시 제2021-17호 제16조에 의거하고, 국외는 국제원자력기구(IAEA: International Atomic Energy Agency)에서 안전기준을 제시하고 있다(IAEA, 2011). 따라서 국내 중·저준위 방사성폐기물 처분시설은 2006년부터 광역 지질을 포함한 부지 지질/지형, 기상, 수문, 수리지질, 인문사회 등을 망라한 조사를 시행하여 부지 현황에 대한 분석 및 안정성 평가를 수행한다. 부지감시의 수문·지구화학 분야에서는 현장 수질 측정 6항목과 실내 분석 26항목을 감시하고 있으나, 본 연구는 이 중 9개 항목(EC, Na, K, Ca, Mg, SiO₂, Cl, SO₄, HCO₃)을 선정하여 분석하였다. 연구 목적은 물시료 분석자료의 주성분-다중선형회귀-군집 분석과 Piper Diagram 분석결과로부터 해수와 담수(지하수)와의 특성분석 및 해수 영향을 분석하는 것이다. 현장 부지내 지하수 7개 관정(GM-1, 2, 4, 5, 6, 7, 8)과 해수 2개 지점(Sea-1, 2)을 대상으로 통계학적 주성분 분석결과, 대부분의 지하수는2개~4개의 요인으로 구분되고, 해수와의 유사성을 해석하기 위해 확인한 관정은 GM-5, GM-6, GM-1 지점으로 분류되었다. 상기와 같이 해수의 영향을 확인하기 위해 해수 2개 지점과 동일한 군집으로 분류되는 지하수는 GM-5 관정으로 확인되었고, 해안선에서 가까운 GM-5 관정과 같이 유사한 거리에 분포한 지하수 GM-1, 2, 4 관정은 2개 혹은 3개의 최적 군집으로 분류하였을 때도 GM-5와는 다른 특성을 보여주었다. 이는 해안과 인접하더라도 수질은 다른 지질학적 특성(지형, 기상, 단열대 등)에 따라 영향받았음을 지시한다.

• 대한한의학회지
• /
• 제30권2호
• /
• pp.63-78
• /
• 2009

Objective: The purpose of experimental study was to prove the effects of Boyangmakseong-bang (BYMSB) treatment on cBSA-induced in a MN mouse model. Methods: We divided mice into 4 groups. The Normal group had no treatment. We used cBSA and induced MN mouse model to the other 3 groups. The Control group was treated with cBSA (9mg/kg i.p) only. The second group, named 'BY-250', was treated with cBSA (9mg/kg i.p) and BYMSB extract (250mg/kg, p.o). The third group, named 'BY-500', was treated with cBSA (9mg/kg i.p) and BYMSB extract (500mg/kg, p.o). After cBSA and BYMSB extract treatment for 4 weeks, the increase in percentage of body weight, proteinuria, serum albumin, total cholesterol, creatinine and BUN of all groups were measured. The CD3+, CD19+, CD4+, CD8+ cell levels of spleen of all groups were analyzed. IgA, IgG, IgM, IL-$1{\beta}$, TNF-${\alpha}$, IL-6 and IFN-${\gamma}$ levels of all groups were gauged. H&E staining, immunofluorescence staining and electron microscopy of kidney were observed. Results: BYMSB showed significant decrease in the 24hrs proteinuria, serum total cholesterol, serum IgG levels and BUN levels, and showed significant increase in the serum albumin levels compared with the control group. BYMSB showed increase in the increasing percentage of body weight and IFN-${\gamma}$ levels compared with the control. BYMSB showed decrease in the CD3+ T cells, CD4+ Th cells, IL-$1{\beta}$, TNF-${\alpha}$ and IL-6 levels, but did not show significant change compared with the control. BYMSB showed considerable decrease in the thickening of the GBM on H&E staining, deposition of IgG on immunofluorescence staining and deposition of electron-density on electron microscopy of kidney compared with the control. Conclusions: According to the above results, it is suggested that BYMSB decreases the symptoms of MN induced by cBSA in a mouse model. Therefore BYMSB seems to be applicable to MN in clinical practice.

• 대한치과보철학회지
• /
• 제30권2호
• /
• pp.135-154
• /
• 1992

This study was performed to analyze bond strength, the alterations of the interfaces between metal films which are populary used and considered to contribute to the chemical reaction with porcelain, according to constant ion- beam- mixing, and the relation between interfacial chemical reactions and bond strength in metal/porcelain specimens. For this study, three seperate metals : selected-gold, indium and tin were chosen ; each to be bonded to a seperate body porcelain. Bonding occurs when the metal is deposited to the body porcelain using a vacuum evaporator. The vacuum evaporator used $10^{-5}\sim10^{-6}$ Torr vacuum states for the evaporation of various metals (Au, Sn, In). Ion-beam-mixing of the porcelain/metal interfaces caused reactions when the Ar+ was implanted into thin films using a 80 KeV accelerator. These ion-beam-mixed specimens were then compared with an unmixed control group. An analysis of bond strength and ionic changes between the the metal and porcelain was performed by electron spectroscopy of chemical analysis (ESCA) and scratch test. The finding led to the following conclusions : 1. Light microscopic views of the scratch test : The ion-beam-mixed Au/porcelain specimen showed narrower scratched streams than the unmixed specimen. However, the Sn/porcelain, In/porcelain specimens showed no differences in the two conditions. 2. Acoustic emissions in scratch tests : The ion-mixed Au/porcelain, In/porcelain specimens showed signals closer to the metal/porcelain interfaces than unmixed specimens. Conversely, the ion-mixed Sn/porcelain specimen showed more critical signals in superficial portions than unmixed specimens. 3. After ion- beam-mixing, the Au/porcelain specimen showed apparently increased bond strength, and the In/porcelain specimen showed very slightly increased bond strength. However, the Sn/porcelain specimen showed no differences between ion mixed specimen and the unmixed one. 4. ESCA analysis : The ion-beam-mixed Au/porcelain specimen showed a higher peak separated value (4.3eV) than that of the unmixed specimen(3.65eV), the ion-beam-mixed In/porcelain specimen showed a higher peak separated value (9.43eV) than that of the unmixed specimen(7.6eV) and the ion-beam-mixed Sn/porcelain specimen showed a higher peak separated value (8.79eV) than that of the unmixed specimen(8.5eV). 5. Interfacial changes were observed in the ion-mixed Au/porcelain, In/porcelain and Sn/porcelain specimens. Especially, significant interfacial changes were measured in the ion- mixed Sn/porcelain specimen. Tin dioxide(SnO2) and a combination of pure tin and tin dioxide (Sn+SnO2) were produced. 6. In the Au/porcelain specimen, the interfacial chemical reaction showed increased bond strength between gold and porcelain substrate. But, in the In/porcelain, Sn/porcelain specimens, interfacial chemical reactions did not affected the bond strength between metal and porcelain substrate. Especially, bonding strength on the ion mixed Sn/porcelain specimen showed the least amount of difference.