• 한국표면공학회지
• /
• 제35권1호
• /
• pp.5-10
• /
• 2002

This study was performed to investigate the influence of spraying condition to the coating layer properties of Fe-Cr-Ni-Mo-Si-B alloy using the HVOF. The investigations, such as thickness measurement, surface roughness, hardness, friction coefficient, resistance of corrosion were carried out. Matrix is prepared by gritting and coating layer is made of Fe-Cr-Ni-Mo-Si-B alloy powder using HVOF. Alumina gritting layers are superior to steel gritting layers. The less spaying distance, the more coating layer properties confirmed. The optimum spraying condition, in this study, was proved as 13inch spraying distance with feed rate 350rpm (78g/min).

• 한국해양공학회지
• /
• 제16권6호
• /
• pp.60-64
• /
• 2002

This paper describes the machining characteristics of the MoSi$_2$--based composites through the process of electric discharge drilling with various tubular electrodes. In addition to hardness characteristics, microstructures of Nb/MoSi$_2$laminate composites were evaluated from the variation of fabricating conditions, such as preparation temperature, applied pressure, and pressure holding time. MoSi$_2$-based composites have been developed in new materials for jet engines of supersonic-speed airplanes and gas turbines for high-temperature generators. These high performance engines may require new hard materials with high strength and high temperature-resistance. Also, with the exception of grinding, traditional machining methods are not applicable to these new materials. Electric discharge machining (EDM) is a thermal process that utilizes a spark discharge to melt a conductive material. The tool electrode is almost -unloaded, because there is n direct contact between the tool electrode and the work piece. By combining a non-conducting ceramic with more conducting ceramic, it was possible to raise the electrical conductivity. From experimental results, it was found that the lamination from Nb sheet and MoSi$_2$ powder was an excellent strategy to improve hardness characteristics of monolithic MoSi$_2$. However, interfacial reaction products, like (Nb, Mo)SiO$_2$and Nb$_2$Si$_3$formed at the interface of Nb/MoSi$_2$, and increased with fabricating temperature. MoSi$_2$composites, with which a hole drilling was not possible through the conventional machining process, enhanced the capacity of ED-drilling by adding MbSi$_2$, relative to that of SiC or ZrO$_2$reinforcements.

• 생명과학회지
• /
• 제12권1호
• /
• pp.16-25
• /
• 2002

다시마의 조체 연화와 유용성분 추출 방법을 검토하여 다시마를 이용한 엽상 및 분말차 제조를 검토하였다. 다시마 엽체 연화를 위하여 0.05% 초산용액의 9$0^{\circ}C$에서 0.5시간, 0.2% 제2인산칼륨용액의 10$0^{\circ}C$에서 0.5시간, 0.3% 탄산나트륨용액의 10$0^{\circ}C$에서 0.5시간 자숙처리하는 것이 적당하였다. 그리고 0.05% 초산용액의 9$0^{\circ}C$서 0.5시간 자숙하여 엽체를 연화시키고 조미첨가제로서 0.5% glutamic acid, 3% glycine, 5% sorbitol 및 1.5% soy sauce를 다시마 중량에 대하여 10% 첨가하여 약한 불에서 1시간 졸여서 제조한 엽상차가 관능검사에서 씹힘성, 단맛, 향 및 색택이 가장 우수하게 평가되었다. 엽상차 액의 유리아미노산 함량은 alanine이 707.2 $\mu$mo1/100 $m\ell$로 가장 많이 함유되어 있었으며, 그 다음으로 glutamic acid가 343.6 $\mu$mo1/100 $m\ell$이었고, 무기성분은 Na이 49.378 ppm으로 가장 많았으며, 다음으로 Mg 10.72 ppm, K 10.56 ppm 및 Ca 6.55 ppm 순이었다. 11$0^{\circ}C$에서 1.5시간 가압처리한 다시마 분말의 용출액이 점도가 가장 낮아 1.73 cP이었고 총고형물 및 회분함량은 가장 높아 각각 2.22% 및 1.48% 이었다. 여기에 0.05% glutamic acid, 5% glycine, 5% glucose 및 4% sodium chloride를 첨가하여 분말차로 제조하였고, 분말차 2g을 9$0^{\circ}C$에서 10분간 우려낸 물의 유리 아미노산 중 glycine이 222.04 $\mu$mo1/100 $m\ell$로 가장 많이 함유되었고 그 다음으로 glutamic acid는 208.58 $\mu$mo1/100 $m\ell$이었다. 그리고 무기성분으로는 Na이 104.24 ppm으로 가장 많은 양이 함유되어 있었으며, 다음으로 Mg 14.31 ppm, K 9.68 ppm, Fe 2.36 ppm, Ca 2.00 ppm, Zn 0.13 ppm, Cu 0.10 ppm 및 Mn 0.01 ppm의 조성을 보였다.

• 한국표면공학회지
• /
• 제49권6호
• /
• pp.507-512
• /
• 2016

Expensive silver powder is used to form electrodes in most IT equipment, and recently, many attempts have been made to lower manufacturing costs by developing powders with Ag-Ni or Ag-Cu core-shell structures. This study examined the sintering behavior of Ag-Ni electrode powder with a core-shell structure for silicon solar cell with high energy efficiency. The electrode powder was found to have a surface similar to pure Ag powder, and cross-sectional analysis revealed that Ag was uniformly coated on Ni powder. Each electrode was formed by sintering in the range of $500^{\circ}C$ to $800^{\circ}C$, and the specimen sintered at $600^{\circ}C$ had the lowest sheet resistance of $5.5m{\Omega}/{\Box}$, which is about two times greater than that of pure Ag. The microstructures of electrodes formed at varying sintering temperatures were examined to determine why sheet resistance showed a minimum value at $600^{\circ}C$. The electrode formed at $600^{\circ}C$ had the best Ag connectivity, and thus provided a better path for the flow of electrons.

• 한국전기전자재료학회논문지
• /
• 제23권12호
• /
• pp.966-972
• /
• 2010

Single-phase $Sr_2FeMoO_6$ thin films were produced by RF magnetron sputtering for use as electrodes in integrated sensors and found to be good conductors at room temperature. The films were deposited from a powder-type sputtering target under various conditions, and were crystallized by annealing. Elimination of $O_2$ gas during deposition, by the use of a solely Ar sputtering gas under a working pressure as low as possible, and vacuum annealing were important to promote the $Sr_2FeMoO_6$ phase. However, oxygen exclusion from sputtering and annealing was not enough to yield single-phase $Sr_2FeMoO_6$: hydrogen annealing was also required. Film production was optimized by varying the deposition parameters and hydrogen annealing conditions. The film had good electrical conduction, with a low resistivity of $1.6{\times}10^{-2}\Omega{\cdot}cm$ at room temperature.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2011년도 춘계학술발표대회
• /
• pp.49.2-49.2
• /
• 2011

$PbMoO_4$ nanoparticles were successfully obtained in the presence of ethylene glycol (EG) with the assistance of a prolonged sonication process. The nanoparticles were characterized by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), diffuse reflectance spectroscopy (DRS) and adsorption-desorption $N_2$ isotherms (BET). The catalyst prepared sonochemically showed higher photocatalytic activity than $PbMoO_4$ prepared by solid-state reaction in the degradation reactions of rhodamine B (rhB), indigo carmine (IC), orange G (OG), and methyl orange (MO) under UV-Vis light radiation. In order to elucidate aspects of the degradation mechanism of the organic dyes, some experimental variables were modified such as pH, $O_2$ level in solution, and radiation source. In general, the photocatalytic activity for the degradation of organic dyes followed the sequence IC>OG>rhB>MO.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회B
• /
• pp.2007-2010
• /
• 2008

Vanadium pentoxide ($V_2O_5$) powder was prepared and mixed with Molybdenum Oxides ($MoM_3$) to form Mo-doped and -undoped $VO_2$ films by a sol-gel method on graphite conductive substrates. X-Ray diffraction (XRD) and scanning electron microscopy (SEM) was used to investigate the chemical compositions and microstructures of the Mo-doped and -undoped $VO_2$ films. The variation of electrical resistance was measured as a function of temperature and stoichiometric composition between vanadium and molybdenum. In this study, it was found that Mo-doped and -undoped $VO_2$ shows the typical negative temperature coefficient (NTC) behavior. As the amount of the molybdenum increases, the electrical resistance of Modoped $VO_2$ film gets reduced under the transition temperature and a linear decrease in the transition temperature is observed. From these experimental results, we can conclude that the electrical resistance behavior with temperature change of $VO_2$ films can be utilized as a self-heating source with the electrical current flowing through the graphite substrate.

• 한국세라믹학회지
• /
• 제54권3호
• /
• pp.200-204
• /
• 2017

Molybdenum (Mo), an electrode material of alkali metal thermal-to-electric converters (AMTEC), facilitates grain growth behavior and forms Mo-Na-O compounds at high operating temperatures, resulting in reduced performance and shortened lifetime of the cell. Mo/TiN composite materials have been developed to provide a solution for such issues. Mo is a metal that possesses excellent electrical properties, and TiN is a ceramic compound with high-temperature durability and catalytic activity. In this study, a dip-coating process with an organic solvent-based slurry was used as an optimal coating method to achieve homogeneity and stability of the electrodes. Cell performance was evaluated under various conditions such as the number of coatings, ranging from 1 to 3 times, and heat treatment temperatures of $800-1100^{\circ}C$. The results confirmed that the cell yielded a maximum power of 9.99 W for the sample coated 3 times and heat-treated at $900^{\circ}C$.

• 대한금속재료학회지
• /
• 제50권9호
• /
• pp.653-657
• /
• 2012

In this study, a molybdenum disilicide ($MoSi_2$) coating process was investigated by hydrogen reduction and Si-pack cementation. At first, the metallic Mo coating was carried out by hydrogen reduction of $MoO_3$ powder at $750^{\circ}C$ for various holding times (1, 2, 3 h) in hydrogen atmosphere. A $4.3{\mu}m$ thick metallic molybdenum thin film was formed at 3 h. $MoSi_2$ was obtained by Si-pack cementation on molybdenum thin film through hydrogen reduction processing. It was carried out using $Si:Al_2O_3:NH_4Cl=5:92:3$ (wt%) packs at $900^{\circ}C$ for various holding times (30, 60, 90 min) in Ar atmosphere. When the holding time was 90 min, a $MoSi_2$ layer was coated successfully and a $15.4{\mu}m$ thickness was observed.

• 대한화학회지
• /
• 제67권1호
• /
• pp.33-41
• /
• 2023

Nanocrystallne WO₃ and MoO₃ with several different sizes and crystal structures were prepared by simple acid precipitation and subsequent heat treatment. The photochromic (PC) properties of these samples were comparatively investigated in powder state by monitoring diffuse reflectance spectral changes after bandgap irradiation. The PC effect of hexagonal WO₃ and monoclinic WO₃ strongly depended upon crystallite size rather than crystal structure. The smaller the crystallite size, the better the PC effect. However, orthorhombic WO·H₂O and MoO₃ having hexagonal and orthorhombic structures did not follow this trend. One consistent result for all WO₃ and MoO₃ samples is that the heat treatment in air, which changes crystallinity, whether it changes the crystal structure or only the crystallite size, reduces the PC effect. Since the thermal treatment reduces the surface oxygen defect sites, we believe that the PC effect of WO₃ and MoO₃ depends critically on the surface oxygen defect sites that serve as deep trap sites for photogenerated electrons and oxygen radical holes. We also found that the proton insertion claimed by double charge injection model is not critical for the PC effect.