• 한국식품영양학회지
• /
• 제32권3호
• /
• pp.259-266
• /
• 2019

The objective of this study was to investigate quality characteristics of sourdough bread with fermented Zante currants juice. The sweetness of fermented Zante currants starter increased while its pH value decreased as time passed. The pH values were negatively correlated to the added amount of starter with the lowest pH being recorded at 70% addition. Similarly, bread's moisture was inversely correlated to the added amount of starter with the highest moisture content being recorded at 10% addition. For bread's height, excluding the control, 70% addition turned out to be the highest, and the height decreased as the added amount increased. The oven-spring was similar between the control and 70% addition. For the volume, except the control, 70% addition turned out to be the largest. The larger the specific volume was, the higher the volume of bread got. The brightness, redness, and yellowness were decreased as the added amount was increased. For the texture, the control had the highest elasticity and cohesiveness, and they increased as the added amount of starter increased. The hardness had a negative correlation with the added amount, and 70% addition yielded the same result as the control. The adhesiveness appeared only in 10% addition.

• 열처리공학회지
• /
• 제11권2호
• /
• pp.82-91
• /
• 1998

The elastic modulus and wear resistance in austempered ductile cast iron(ADI) are two important mechanical properties for automobile parts. Therefore, the effect of Cu, Ni, Mo and special austempering treatment such as preheated, prequenched, and step austempering treatments on elastic modulus and wear resistance has been investigated systomatically. As a result, elastic modulus and wear resistance were increased by the addition of Mo-Cu and preheated austempering treatment.

• 한국환경과학회지
• /
• 제8권2호
• /
• pp.241-248
• /
• 1999

The photocatalytic decolorization and photodegradation of wastewater contamininated with dyes such as methyleneblue tetrahydrate(MBT), methyl orange(MO), phenol red(PR) and the mixed dyes have been studied using a batch reactor in the presence of aerotropic and titania. Degussa P25 titanium oxide was used as the photocatalyst and proved to be effective for the dyes-degradation when irradiated with UV-light source emitting the wavelength of 253.7 nm in the presence of air. In addition to removing the color from the wastewater, the photocatalytic reaction simultaneously reduced the COD and optical density which suggests that the dissolved organic compounds have been photooxidized. The reaction rate of disappearance of the dyes were measured as a function of the irradiation times. The photooxidative procedure of the aquatic solution have the first order reaction-kinetics. The rate constants were increased in the order of PR < MBT < $gL^{-1}-TiO_2$ powder were irradiated with the UV -light source.

• 한국진공학회지
• /
• 제8권4A호
• /
• pp.456-460
• /
• 1999

Experimental studies of laser micromachining on Mo diaphragm using piezo Q-switched Nd:YAZ laser have been performed. Application of miniaturized micorcolumn electron gun arrays as a potential electron beam lithography or portable mini-scanning electron microscope (SEM) application have recently extensively examined. The conventional microcolumn fabrication technique would give a limitation on the minimization of aberration, In this paper, we obtained 20~30 $\mu \textrm m$aperture of laser micromachining on Mo diaphragm using piezo Q-swithed Nd:YAG laser. The geometrical figures, such as the diameter and the preciseness of the drilled aperture are dependent upon the total energy of the laser pulse train, laser pulse width, and the diameter of laser spot in addition to the materials-dependent parameters.

• 한국세라믹학회지
• /
• 제30권6호
• /
• pp.429-432
• /
• 1993

Cr3C2 material is characterized by high chemical stability and poor sinterability with low strength [50~150MPa]. In his study, low melting temperature nickel powder was used to improve sinterability as well as strength. In addition, molydenum particles were added to the Ni-bonded Cr3C2 cermet pseudomatrix to increase resistance to fracture. The specimens made by hot-pressing under vacuum and strength was measured by 4-point bending. Indentation cracking and fractographic examination were conducted to study the interaction of the indentation cracks with the reinforcing particles. Toughening mechanisms and failure will be discussed in terms of crack/particle interactions and compared with previous works.

• 한국세라믹학회지
• /
• 제18권2호
• /
• pp.83-90
• /
• 1981

In this study, the effect of additions on magnetic properties in the system of [$Ni_{0.32}Zn_{0.68}$] 1-x Mx $Fe_2O_4$ have been investigated. The additions, Co or Mg or Cu, was added in turn in place of M, and its composition was varied from 0.1 mo1% to 0.5 mo1%. The materials were blended by hot petroleum drying method, and sintered with the rate of 30$0^{\circ}C$/h in the air. The sintering temperatures were varied from 110$0^{\circ}C$ to 130$0^{\circ}C$, with the intervals of 5$0^{\circ}C$, and matured for 3hrs. The results are: 1) The permeability decreased when the addition, MgO or CoO, was added, and it increased when CuO was added. 2) Resistivity had the lowest Value when CuO was added.

• 센서학회지
• /
• 제29권1호
• /
• pp.1-6
• /
• 2020

Gas sensors that operate at room temperature have been extensively studied because of sensor stability, lift time, and power consumption. To design effective room-temperature gas sensors, various nanostructures, such as nanoparticles, nanotubes, nanodomes, or nanofibers, are utilized because of their large-surface-to-volume ratio and unique surface properties. In addition, two-dimensional materials, including MoS₂, SnS₂, WS₂, and MoSe, and ultraviolet-activated methods have been studied to develop ideal room-temperature gas sensors. Herein, a brief overview of state-of-the-art research on room-temperature gas sensors and their sensing properties, including nanostructured materials, two-dimensional materials, the ultraviolet-activated method, and ionic-activated gas sensors, is provided.

• 한국주조공학회지
• /
• 제17권1호
• /
• pp.51-57
• /
• 1997

Effects of the amount of flake type graphite, morphology and (V,Mo)carbides on the specific damping capacity of austenitic low thermal expansion cast irons were investigated. Specific damping capacity(SDC) of low thermal expansion cast irons increased with the increased amount of graphite. Specific damping capacity of low thermal expansion cast iron decreased with the increased Young's modulus. In the case of V and Mo addition, SDC decreased with the increased amount of carbides. Specific damping capacity increased about 2% by the movement of magenetic domains which appeared in ferromagnetic materials.

• Corrosion Science and Technology
• /
• 제16권4호
• /
• pp.167-174
• /
• 2017

Bicarbonate/carbonate and molybdate anions have been characterized for their inhibitive effect on pitting corrosion of carbon steel in simulated concrete pore solution by using electrochemical tests such as electrochemical impedance (EIS) and linear polarization (LP). It was revealed that bicarbonate/carbonate has a weak inhibitive effect on pitting corrosion that is approximately one order of magnitude lower compared to hydroxide. Molybdate is effective against pitting corrosion induced by the concentration of chloride as low as 113 mM and can increase the pitting potential of a previously pitted sample to the oxygen evolution potential by the concentration of molybdate as much as 14.6 mM only. The formation of a $CaMoO_4$ film on the surface hinders the reduction of dissolved oxygen on the steel surface, reducing corrosion potential and increasing the safety margin between corrosion potential and pitting potential further. In addition, pore-plugging by $FeMoO_4$ as a type of salt film within pits increases the likelihood of repassivation.

• 한국정밀공학회지
• /
• 제25권7호
• /
• pp.131-138
• /
• 2008

The microstructural effects on the ultrasonic nonlinearity were investigated in isothermally degraded ferritic 2.25Cr-1Mo steel and low cycle fatigued copper. The variation in ultrasonic nonlinearity (${\beta}/{\beta}_0$) was interpreted as resulting from microstructural changes supported by the electron microscopy and X-ray diffraction, in addition to the mechanical test (Victor's hardness and ductile-brittle transition temperature). The ultrasonic nonlinearity of 2.25Cr-1Mo steel increased abruptly in the initial 1,000 h of degradation, and then changed little due to the coarsening of carbide and precipitation of stable $M_6C$ carbide during isothermal degradation. The ultrasonic nonlinearity of copper increased with the fatigue cycles due to the evolution of dislocation cell substructure.