• Journal of Magnetics
• /
• v.8 no.1
• /
• pp.32-35
• /
• 2003

Magnetic funnel Junctions (MTJs) were fabricated on thermally oxidized Si (100) wafers using DC magnetron sputtering. The film Structures were Ta(50 ${\AA}$)/CU(100 ${\AA}$)$Ni_{80}Fe_{20}(20 $ ${\AA}$)/Cu(50 ${\AA}$)/$Mn_{75}Ir_{25}(100 $ ${\AA}$)/$Co_{70}Fe_{30}(25$ ${\AA}$)/Al-O(15 ${\AA}$)/$Co_{70}Fe_{30}(25 $ ${\AA}$)/$Ni_{80}Fe_{20}(t)/Ta(50 $ ${\AA}$), with t=0 ${\AA}$, 100 and 1000 ${\AA}$, respectively. X-ray diffraction has shown improvement of (111) texture of IrMn$_3$ and Cu by annealing. The exchange-biased energy is almost inversely proportional to temperature. The difference between the coercivity H$_c$ and the exchange biased field H$_E$ for t = 0 $_3$ sample is smaller than that for t = 1000 ${\AA}$. For the pinned layer, the decreasing rate of the coercivity with the temperature is higher compared to that of the exchange field, but variation of H$_c$ is similar to that of the exchange field for free layer.

• Journal of the Mineralogical Society of Korea
• /
• v.13 no.4
• /
• pp.205-220
• /
• 2000

북동태평양 C-C지역의 우리나라 광구에서 산출되는 망간단괴의 내부조직을 크게 주상조직 층상대, 첨상조직 층상대, 첨상조직 괴상대, 첨상조직 다공질대 및 괴상조직 괴상대로 구분하였다. 주상조직 층상대에서는 버나다이트(vernadite)가 가장 우세하게 산출되며, 첨상조직 층상대에서는 부서라이크(buserite)가 함께 산출된다. 첨상조직 괴상대는 부서라이트의 산출이 두드러지며, 부분적으로 토도로카이트(todorokite)가 수반된다. 첨상조직 다공질대는 첨상체 또는 구상체로 이루어지며 부분적으로 괴상조직으로 교대되는데 주로 토도로카이트와 부서라이트로 구성되어 있다. 괴상조직을 갖는 괴상대에서는 토도로카이트와 버네사이트(birnessite)가 부서라이트와 함께 산출된다. 각 조직대별로 미세조직을 이루는 엽리들에 대해 전자현미분석을 실시하였다. 엽리의 화학조성을 구성하는 요인은 상관계수 군집분석에 의해 Mn-K의 Mn군, Cu-Ni-Zn-Mg(Ca-Na)의 Cu-Ni-Mg군 Fe-Co-Ti(Ca-P)의 Fe군과 Si-Al의 Si군 등 네 개군으로 구분된다. 각 조직대는 세 개 또는 네 개의 군으로 구성되며 이들 각군은 단괴에서 산출되는 광물과 밀접한 관계를 가진다. Mn군은 토도로카이트, Cu-Ni-Mg군은 부서라이트, Fe군은 함코발트수산화철광물, 그리고 Si군은 규산염광물에서 주로 기인하는 것으로 생각된다. 엽리의 화학조성은 이들 광물의 조합과 구성광물의 화학조성에 따라 지배되고 한 조직대내에서도 여러종류의 조합을 보이는데 이는 각 조직대의 엽리들의 성인과 밀접한 관련이 있는 것으로 생각된다.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.10a
• /
• pp.1440-1445
• /
• 2008

There are 21 abondoned coal mines drained out mine water in gyeong sang do. We monitored the water quality of 31 mine drainage from 1995. The most of mine drainage was neutral as the average pH was 6.22 and Fe, Mn, Al concentration was below 10mg/L. The result showed the tendency of decreasing of flow and metal concentration. The highest Mn concentration was detected in bonghwa area and the hightest Fe concentration was detected in munkyung area. It means that the water quality is closly related to geological features.

• Corrosion Science and Technology
• /
• v.6 no.1
• /
• pp.1-6
• /
• 2007

Ferritic stainless steels for the SOFC interconnect applications are required to possess not only a good oxidation resistance, but also a high electrical conductivity of the oxide scale that forms during exposure at the SOFC operating environment. In order to understand the effects of alloying elements on the oxidation behavior of ferritic stainless steels and on the electrical properties of oxide scales, two kinds of commercial ferritic stainless steels, STS 430 and STS 444, were investigated by performing isothermal oxidations at $800^{\circ}C$ in a wet air containing 3% $H_{2}O$. The results showed that STS 444 was superior to STS 430 in both of the oxidation resistance and the area specific resistance. Although STS 444 contained a less amount of Mn for the $(Mn,Cr)_{3}O_{4}$ spinel formation than STS 430, the minor alloying elements of Al and Mo in STS 444, which were accumulated in the base metal region adjacent the scale, were suggested to reduce the scale growth rate and to enhance the scale adherence to the base metal.

• Journal of Welding and Joining
• /
• v.7 no.2
• /
• pp.49-59
• /
• 1989

The effect of non-metallic inclusions on the HAZ hydrogen induced cracking was investigated. Quench and temper high tensile strength steels containing various sulphur contents were employed. The sulphur contents range between 0.007% and 0.040%. Non-metallic inclusions were mainly MnS type sylphide and Mn-Al-Si type. The sensitivity of HAZ delayed cracking was evaluated by implant testing. Diffusible hydrogen content was varied by controlling the moisture absorbing condition of manual arc welding electrodes. The one was asreceived condition, the other was dipping the electrodes in the water for ten minutes. The main results obtained were as follows; 1) The results of implant test showed that critical stress increased with increasing S content up to 0.013%. But steel containing 0.040%S showed lower critical stress than that of 0.013% S. These result suggest that there will be optimum S content to prevent HAZ delayed cracking of high strength steels. 2) Under the lower D.H.C. level, critical stress was increased with rolling reduction, but higher D.H.C. level, effect of rolling reduction was not recognized.

• Korean Journal of Metals and Materials
• /
• v.47 no.4
• /
• pp.228-234
• /
• 2009

It is well known that the formation of $SiO_2$, $Al_2O_3$ and/or other oxides at the steel surface during the annealing process deteriorates the surface quality of galvanized steels. It is important to minimize oxide formation during the annealing process for the superior surface quality of galvanized steels. In order to minimize the oxide formation on the steel surface, antimony was chosen as an alloying element to the commercial steels. Then, the effect of alloying element on the oxidation behavior was investigated. A small amount of antimony was added to two types of steels, one with 0.1% C, 1.0% Si, 1.5% Mn, 0.08% P, and the other with 0.002% C, 0.001% Si, 0.104% Mn, 0.01% P. Then, the oxidation behavior was investigated from $650{\sim}900^{\circ}C$ in the air. The addition of antimony to the steels retarded the outward diffusion of elements during the oxidation, resulting in reduction of the oxidation rate.

• Journal of the Korean institute of surface engineering
• /
• v.54 no.2
• /
• pp.43-52
• /
• 2021

The Ni-based superalloy, Inconel 740, was corroded between 800 and 1100℃ for up to 100 hr in air and Ar-0.2%SO₂ gas in order to study its corrosion behavior in air and sulfur/oxygen environment. It displayed relatively good corrosion resistance in both environment, because its corrosion was primarily dominated by not sulfidation but oxidation especially in Ar-0.2%SO₂ gas. Such was attributed to the thermodynamic stability of oxides of alloying elements when compared to corresponding sulfides. The scales consisted primarily of Cr₂O₃, together with some NiAl₂O₄, MnCr₂O₄, NiCrMnO₄, and rutile-TiO₂. Sulfur from SO₂ gas made scales prone to spallation, and thicker. It also widened the internal corrosion zone when compared to air. The corrosion resistance of IN740 was mainly indebted to the formation of protective Cr₂O₃-rich oxides, and suppression of the sulfide formation.

• International Journal of Korean Welding Society
• /
• v.3 no.2
• /
• pp.24-28
• /
• 2003

This study was aimed to evaluate the quality of flash welded joints and optimize the welding process for flash butt welding of 780MPa grade high strength steel. And then the relationship between the welding process variables and the joint quality would be established. The effect of process variables between flashing and upsetting process was elucidated. Microstructure observation of the joint indicated that the decarburized band was mainly changed with upsetting process. Width of HAZ was also related to the upsetting conditions rather than the flashing conditions. Generally maximum hardness at HAZ was correlated with Ceq of steel and the empirical relationship was obtained to estimate the HAZ properties. Tensile elongation at the joint was usually decreased with increasing the initial clamping distance. Investigation of fracture surface after tensile and bending tests reveal that the origin of cracking at the joint was oxide inclusions composed of $SiO_2$, MnO, $Al_2O_3$, and/or FeO. The amount of inclusions was dependent on the composition ratio of Mn/Si in steel. If this ratio was above 4, the amount of inclusions was low and then the resistance to cracking at the joint was enough to maintain the joint performance. It was obtained that the flashing process influenced the conditions for the energy input to establish uniform or non­uniform molten layer, while the upsetting conditions influenced the joint strength. Heat input variable during flashing process was also discussed with the joint properties.

• Asian Journal of Atmospheric Environment
• /
• v.11 no.2
• /
• pp.122-130
• /
• 2017

The main purpose of the study was to clarify the properties of individual particles collected at each behavior space of a factory worker. The samplings of size-segregated ($PM_{2.1-1.1}$ and $PM_{4.7-3.3}$) indoor particles were conducted at three different behavior spaces of a factory worker who is engaged in an auto parts manufacturing plant (i.e., his home, his work place in factory, and his favorite restaurant). Elemental specification (i.e., relative elemental content and distribution in and/or on individual particles) was performed by a micro-PIXE system. Every element detected from the coarse particulate matters of home was classified into three groups, i.e., a group of high net-counts (Na, Al, and Si), a group of intermediate net-counts (Mg, S, Cl, K, and Ca), and a group of minor trace elements (P, Ti, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, and Pb). The results of EF for $PM_{4.7-3.3}$ in home indicated that several heavy metals were generated from the sources within the house itself. An exceptional feature shown in the individual particles in workplace is that Cr, Mn, and Co were clearly detected in both fine and coarse particles. Cluster analysis suggested that the individual coarse particles ($PM_{4.7-3.3}$) collected at the indoor of factory were chemically heterogeneous and they modified with sea-salt, mineral, and artificially derived elements. The principal components in individual coarse particles collected at restaurant were sea-salt and mineral without mixing with harmful trace elements like chromium and manganese. Compared to the indoor fine particles of home and restaurant, many elements, especially, Cl, Na, Cr, Mn, Pb, and Zn showed overwhelmingly high net-counts in those of factory.

• Asian Pacific Journal of Cancer Prevention
• /
• v.13 no.6
• /
• pp.2571-2576
• /
• 2012

Breast cancer is the first of the most common ten cancers in Iraq. Its etiology is multifactorial, oxidative stress and lipid peroxidation being suggested to play important roles in carcinogenesis. The purpose of this study was to investigate the oxidant-antioxidant status in breast cancer patients, by measuring SOD isoenzyme activities (total SOD, CuZn-SOD, Mn-SOD and EC-SOD) in plasma and breast tumors, and by estimating thiobarbituric reactive substances (TBRS) in tissue homogenates. General increase in total SOD activity was observed in plasma and tissue samples of breast tumors, greater in the malignant when compared to benign group (p<0.05). Mn-SOD showed a significant decrease in tissue malignant samples (p<0.05), and insignificant decrease in plasma malignant samples compared with control and benign samples. Plasma EC-SOD activity in both patient benign and malignant breast tumors demonstrated 3.5% and 22.8% increase, respectively. However, there was a decrease in tissue EC-SOD activity in malignant breast tumors when compared with benign. A similar tendency was noted for TBRS. We suggest that elevated total SOD might reflect a response to oxidative stress, and then may predict a state of excess reactive oxygen species in the carcinogenesis process. If there is proteolytic removal of the heparin binding domain, EC-SOD will lose its affinity for the extracellular matrix and diffuse out of the tissue. This will result in a decreased EC-SOD activity, thus leading to an increase in the steady-state concentration of $O^{2-}$ in this domain, and increase in EC-SOD activity in the extracellular fluid. This might explain the results recorded here concerning the decrease in tissue EC-SOD activity and increase in plasma of breast cancer patients.