• Resources Recycling
• /
• v.13 no.6
• /
• pp.37-42
• /
• 2004

The power loss analysis was carried out for Ni-Cu-Zn ferrite sample with different content of NiO and ZnO. The power loss, Pcv decreases monotonically with increasing temperature and attains to a certain value at around 100~120 degrees Celsius. The frequency dependence of Pcv can be explained by Pcv~f$^n$, and n is independent of the frequency, f up to 1 MHz. The Pcv decreases with an increase in ZnO/NiO. The Pcv was separated to hysteresis loss(Ph) and residual loss(Pcv-Ph). The temperature characteristics and compositional dependence of Pcv can be attributed to the Ph, while Pcv-Ph is not affected by both temperature and ZnO/NiO. By analyzing temperature and composition dependence of Ph and initial permeability, ${\mu}_i$ like following equations could be formularized. ${\mu}_i{\mu}_0=I_s^2/(K_I+b{\sigma}_0{\lambda}_s)$ Wh=13.5(I$_s^2/{\mu}_i{\mu}_0)$ Where ${\mu}_0$ is permeability of vacuum, I$_s$ is saturation magnetization, K$_I$ is anisotropy constant, $s_0$ is internal heterogeneous stress, ${\lambda}_s$ is magnetostriction constant, b is unknown constant, and Wh is hysteresis loss per one cycle of excitation (Ph=Wh${\times}$f). Steinmetz constant of Ni-Cu-Zn ferrite, m=1.64~2.2 is smaller than that of Mn-Zn ferrites, which suggests the difference of loss mechanisms between these materials.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.9
• /
• pp.1507-1519
• /
• 1997

This paper aims to clarify the effects of grinding conditions on bending strength in surface grinding of various ferrites with the resin bond diamond wheel. The main conclusions obtained were as follows. At a constant material removal rate, the strength improves with increased wheel depth of cut and decreased workpiece speed. It is desirable to grind at higher peripheral wheel speed and under the critical workpiece speed presented in this paper. Grinding the ferrite of higher brittleness, the wheel depth of cut limited to hold 50% of their inherent strength becomes lower. The effect of various grinding conditions on bending strength becomes more larger in the order of Sr, Mn-Zn and Cu-Ni-Zn. When using the diamond grain of the lower toughness, the bending strength becomes higher, and the wheel wear occurs faster. Considering both bending strength and wheel wear rate, the best concentration of wheel is 100. The ground surfaces exhibit that the fracture process during grinding becomes more brittle in the order of Sr, Mn-Zn and Cu-Ni-Zn.

• Journal of the Korean Ceramic Society
• /
• v.16 no.1
• /
• pp.3-12
• /
• 1979

The effects of sintering temperature and sintering atmosphere on magnetic properties and microstructuresof Mn-Zn ferrites have been studied. Mixture of 52.8mole% $Fe_2O_3$, 26.4mole% MnO, 15.1mole0% ZnO and 5.7mole% NiO was prepared, and 0.1mole% CaO, 0.02mole% $SiO_2$ were added as minor additives. After calcining and ball milling the powder was granulated for compacting. The specimens were sintered at $1, 250^{\circ}$, $1, 300^{\circ}$and 1, 35$0^{\circ}C$ in the various atmosphere of $N_2$, $N^_2\DIV0.6% O_2$, $N_2＋2.7% O_2$, $N_2＋4.1% O_2$, $N^2＋8.2% O_2$ and air for 3 hours and cooled in $N_2$ atmosphere. The grian growth rate and densities increase as sintering temperature and oxygen content of atmosphere increase. At the sintering temperature of $1, 250^{\circ}C$ the initial permeabilities increase as oxygen content of atmosphere increase. At the sintering temperature of$ 1, 300^{\circ}$and $1, 350^{\circ}$ the initial permeabilities show maximum values at $N_2＋4.1% O_2$ atmosphere. The secondary peaks of initial permeabilities are observed between 100$^{\circ}$and 20$0^{\circ}C$, and the positions of secondary peaks move to higher temperature as oxygen content of atmosphere increases. Q-factors decrease as sintering temperature increases and oxygen content of atmosphere decreases.

• Resources Recycling
• /
• v.12 no.6
• /
• pp.26-31
• /
• 2003

The power loss characteristics of Mn-Zn ferrite were observed with the sintering temperature. In case of $1150 ^{\circ}C$ sintering, the core loss increased with measuring temperature, and does not have minimum value at the point where the magnetocrystalline anisotropy be 'zero'. This reason mainly due to the change of core loss mechanism with grain size which affects residual loss. The grain size and sintered density slightly increased with equilibrium oxygen partial pressure at$ 1150 ^{\circ}C$ sintering. The resistivity and initial permeability showed no significance with atmosphere, these results due to complex effect of $Fe^{2+}$ concentration and microstructure change. The core loss at $100^{\circ}C$ decreased as the equilibrium oxygen partial pressure increased.e increased.

• Journal of the Korean Magnetics Society
• /
• v.5 no.4
• /
• pp.269-274
• /
• 1995

The basic composition of Mn-Zn ferrite was $Mn_{0.631}Zn_{0.316}Fe_{2.053}O_{4}$(specimen A), $Mn_{0.584}Zn_{0.312}Fe_{2.104}O_{4}$(specimen B) and $Mn_{0.538}Zn_{0.308}Fe_{2.154}O_{4}$(specimen C) with additional 0.1 mol % $CaCo_{3}$ and 0.04 mol % $V_{2}O_{5}$. For high per¬meability and acceleration of grain growth, $CaCo_{3}$ and $V_{2}O_{5}$. was added. The mixture of the law materials was calcinated at $950^{\circ}C$ for 3 hours and then milled. The compacts of toroidal type were sintered at different temperature($1250^{\circ}C$, $1300^{\circ}C$, $1350^{\circ}C$) for 2 hours in $N_2$ atmosphere. The effects of the various raw material composition and sintered temperature on the physical properties of Mn-Zn ferrite have been investigated. They turned out to be spinel structure by X-ray diffraction and the size of grain from SEM was from $18\;\mu\textrm{m}\;to\;23\;\mu\textrm{m}$. As the sintering temperature was increased from $1250^{\circ}C$ to $1350^{\circ}C$, the initial permeability and magnetic induction has increased and the both of Q factor and coercive force has decreased. The coercive force and curie temperature were almost the same at each specimen Their values were about 0.45 Oe and $200^{\circ}C$. The frequency of specimen will used in the range from 200 kHz to 2 MHz. The basic composition of $Mn_{0.584}Zn_{0.312}Fe_{2.104}O_{4}$(specimen B) sintered at $1300^{\circ}C$ shows the best results at magnetic induction (Br & Bm).

• Journal of the Korean Ceramic Society
• /
• v.30 no.5
• /
• pp.357-364
• /
• 1993

Chemical reaction occurred in the interface of Mn-Zn ferrite and glass after bonding. Effects of the formation of reaction layer on the magnetic properties were investigated. The composition of glass was 23PbO-61SiO2-6ZnO-8Na2O-2K2O and the ferrite was chosen to have a high permeability. Toroid samples of ferrites bonded with glasses, were heat-treated at $700^{\circ}C$, 80$0^{\circ}C$ and 90$0^{\circ}C$ for 1h. The reaction was observed to increase with bonding temperature, resulting in the development of reaction layer. Subsequently the initial permeability was found to be decreased. The permeabilities decreased by 25% with increasing bonding temperature from $700^{\circ}C$ to 80$0^{\circ}C$. At the bonding temperature of 90$0^{\circ}C$, the permeability was decreased by 45%, compared to that of 80$0^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.3 no.5
• /
• pp.497-504
• /
• 1993

Effects of $Ta_2O_5,ZrO_2$ and $SiO_2$ addition on magnetic properties of 0.02wt%$Bi_2O_3$ and 0 . 0 5 wt%$CaCO_3$ doped Mn-Zn ferrites(58.5mol% $Fe_2O_3$, 25.5 mol% ZnO) were investigated. E:lectrlcal resistivity and magnetic properties such as the initial permeability($\mu_i$), loss factor(tan$\delta$), coercive force Hc(m0c) were measured. With lncreasing $Ta_2O_5$ and $ZrO_2$ addition, the following effects were observed: I ) Decreasing of the average grain size; 2) lncreasing of the electrical resistivity and initial permeability; 3) Ilecreasmg of loss factor values. (very low loss esprcially at high frequency region) ; 4 ) Fine and uniform microsrructures were obtamed at O.lwt% nddecl samples. In case of $SiO_2$ addition, anomalous grain growth and degradation of magnetic properties were observed. The obtained maximum initial permeability value was 6260 at IOkHz. $25^{\circ}C$ from 0.02wt%$Bi_2O_3$. 0.05wt%$CaCO_3$, 0.lwt%$Ta_2O_5$ added sample, the corresponded relative loss factor (tan$\delta /\mu_i$)for the sample was $4.2 \times 10^{-6}$.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2004.11a
• /
• pp.3-7
• /
• 2004

An electric power efficiency of electrodeless fluorescent lamp has big relativie property of gas in lamp, gas pressure, lamp formation, ingredients of magnetic substance and shape and action frequency etc. We used magnetic substance that open self-examination material of electrodeless fluorescent lamp antenna. Ferrite that is used in this experiment was Mn-Zn type. We have examined resistance kind, impedance, Q-factor's frequency characteristic by ferrite. Impedance, resistance and capacitance did not show difference in start frequency 2.65 [MHz] but there was difference quantity. We could know Q-factor's difference according to material, and Q-factor's is important part of antenna design.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2004.05a
• /
• pp.50-52
• /
• 2004

• Proceedings of the KIEE Conference
• /
• 2004.11a
• /
• pp.153-156
• /
• 2004

An electric power efficiency of electrodeless fluorescent lamp has big relative property of gas in lamp, gas pressure, lamp formation, ingredients of magnetic substance and shape and action frequency etc. We used magnetic substance that open self examination material of electrodeless fluorescent lamp antenna. Ferrite that is used in this experiment was Mn-Zn type. We have examined resistance kind, impedance, Q-factor's frequency characteristic by ferrite. Impedance, resistance and capacitance did not show difference in start frequency 2.65 [MHz] but there was difference quantity. We could know Q-factor's difference according to material, and Q-factor's is important part of antenna design.