• Korean Journal of Materials Research
• /
• v.27 no.12
• /
• pp.643-651
• /
• 2017

Four types of high Mn TWIP(Twinning Induced Plasticity) steels were fabricated by varying the Mn and Al content, and the tensile properties were measured at various strain rates and temperatures. An examination of the tensile properties at room temperature revealed an increase in strength with increasing strain rate because mobile dislocations interacted rapidly with the dislocations in localized regions, whereas elongation and the number of serrations decreased. The strength decreased with increasing temperature, whereas the elongation increased. A martensitic transformation occurred in the 18Mn, 22Mn and 18Mn1.6Al steels tested at $-196^{\circ}C$ due to a decrease in the stacking fault energies with decreasing temperature. An examination of the tensile properties at $-196^{\circ}C$ showed that the strength of the non-Al added high Mn TWIP steels was high, whereas the elongation was low because of the martensitic transformation and brittle fracture mode. Although a martensitic transformation did not occur in the 18Mn1.9Al steel, the strength increased with decreasing temperature because many twins formed in the early stages of the tensile test and interacted rapidly with the dislocations.

• Journal of Korea Foundry Society
• /
• v.25 no.5
• /
• pp.216-220
• /
• 2005

High ductility Al-Mg alloys often contain some Mn and Si, however the effects of these minor alloying elements on various properties of alloys have not been fully understood. In this study the castability and mechanical properties of Al-5%Mg alloy were investigated according to the addition of Mn and Si. The fluidity of the alloys was generally increased by increasing Si or Mn contents. The feedability was also increased by increasing Si content, but it was rather decreased by increasing Mn content. Both the tensile strength and the ductility appeared to be deteriorated by Si addition, while they were found to be improved by Mn addition.

• Journal of the Korean Chemical Society
• /
• v.43 no.1
• /
• pp.23-29
• /
• 1999

The Al oxide layer formed in 1M $H_2SO_4$ solution and the influence of applied frequency for electrodeposition of Mn on Al oxide layer were characterized using by impedance spectroscopy. Mn compounds were electrodeposited at the base of pores during deposition with applied low frequency voltage. For the Mn deposited oxide layer at 6OHz and 5Hz in 1 g/L $KMnO_4$ solution, in equivalent circuit for interpretation, the resistance ($R_2$) and capacitance ($C_2$) were considered to be due to deposition of Mn on base of pore. The electrochemical behavior of barrier layer and porous oxide layer on Al have been characterized by capacitance ($C_b$) and Young capacitance ($C_Y$) in equivalent circuit model.

• The Korean Journal of Ceramics
• /
• v.4 no.4
• /
• pp.297-303
• /
• 1998

The effect of aliovalent dopants, $ Nb_2O_5$ and MnO, on the phase stability of 12 mol% ceria partially-stabilized zirconia (Ce-TZP) polycrystals was studied. Both dopants (MnO and $ Nb_2O_5$) significantly increased the stability of the tetragonal zirconia phase (Mb temperature lower than liquid nitrogen temperature). The enhancement of the stability of the tetragonal phase in Ce-TZP doped with 1 mol% of Mno(Ce-TZP/MnO) andCe-TZP doped with 1 mol% of $ Nb_2O_5$(Ce-TZP/$ Nb_2O_5$) were explained by the significant reduction of the driving force, -${\Delta}$Gchem, for the tetragonal-to-mono-clinic phase transformation caused by the addition of MnO and $ Nb_2O_5$. The enhanced stability of the tetragonal phase in the Ce-TZP and Al2O3 composite (Ce-TZP/$Al_2O_3$) is believed to be caused by smaller grain size, moderate reduction in the chemical driving force and increase in the strain energy barrier to the transformation. Mechanical properties of the Ce-TZP and the Ce-TZP/$Al_2O_3$ with (i) the same grain size and (ii) the same Mb temperature were examined by measuring stress-strain behavior in 3 point bending. The Ce-TZP/$Al_2O_3$ composite doped with 1.3w% MnO (Ce-TZP/$Al_2O_3$/MnO), which had the same grain size as the Ce-TZP and De-TZP/$Al_2O_3$ showed more transformation plasticity than either the Ce-TZP or the Ce-TZP/$Al_2O_3$ composite. The Ce-TZP wihch had the same Mb temperature as that of the Ce-TZP/$Al_2O_3$/MnO did not show any transformation plasticity.

• Journal of Welding and Joining
• /
• v.28 no.1
• /
• pp.60-65
• /
• 2010

This paper is concerned with effects of Al, Mn and Si contents on spatter, fume, microstructure and mechanical property with 490MPa Grade Flux Core Wire(FCW). Ten kinds of FCW were fabricated by varying Mn, Si and Al contents and each FCW was weld for check the amount of spatter and fume generations, microstructures and mechanical property. Amount of spatter and fume generations was decreased with the increasing Si contents and decreasing by Al contents in FCW. And, their microstructure of weld metal were changed by Mn, Al and Si contents in FCW. With increasing of Al and Si, acicular ferrite was fine and volume fraction of acicula ferrite was increased. Thereby leading to improvement of Charpy impact property and strength.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.2
• /
• pp.64-69
• /
• 2006

Cathode materials of Al-doped $Li(Ni_{1/3}Co_{1/3}Mn_{1/3-x}Al_x)O_2$ (x=0.0, 0.005, 0.01 0.05) for lithium ion batteries were synthesized with ultra-sonic spray pyrolysis method and single-step heat treatment. No secondary phases were found in all synthesized powders. The intensity ratio of $I_{003}\;to\;I_{104}$, however, slightly decreased and the particle size increased with the Al contents. The cells with bare, 0.5 and 1.0 at% Al-doped powders showed the initial discharge capacities of 182, 180 and $184mAhg^{-1}$ in a voltage range of $3.0\sim4.5V$ at 1C rate, and the capacity retentions of 81, 77 and 78% at the end of 30 cycles, respectively. But in the voltage range of $3.0\sim4.6V$, the Al-doping significantly enhanced the cycle stability. For example, the discharge capacity after 50 cycles was maintained to 70% in the 0.5 at% Al-doped sample compared to only 30% in no doped sample. The improvement of the cycle stability was thought to be due to $Mn^{3+}$ ion decrease as the Al doping from the XPS analysis results.

• Bulletin of the Korean Chemical Society
• /
• v.34 no.10
• /
• pp.3005-3012
• /
• 2013

The effect of Mn-promotion on high surface area Al-pillared montmorillonite (AlMMT) supported Co nanoparticles prepared by hydrothermal method have been investigated. A series of different weight% Mn-promoted Co nanoparticles were prepared and characterized by XRD, TPR, TGA, BET and SEM techniques. An increase in the surface area of MMT is observed with Al-pillaring. Fischer-Tropsch catalytic activity of the as prepared catalysts was studied in a fixed bed micro reactor at $225^{\circ}C$, $H_2/CO$ = 2 and at 1 atm pressure. The data showed that by the addition of Mn the selectivity of $C_1$ dropped drastically while that of $C_2-C_{12}$ hydrocarbons increased significantly over all the Mn-promoted Co/AlMMT catalysts. The $C_{13}-C_{20}$ hydrocarbons remained almost same for all the catalysts while the selectivity of $C_{21+}$ long chain hydrocarbons decreased considerably with the addition of Mn. The catalyst with 3.5%Mn showed lowest $C_{21+}$ and highest $C_2-C_{12}$ hydrocarbons selectivity due to cracking of long chain hydrocarbons over acidic sites of MMT.

• Korean Journal of Materials Research
• /
• v.27 no.6
• /
• pp.318-324
• /
• 2017

In this study, two Fe-30Mn-0.2C-(1.5Al) high-manganese steels with different surface conditions were hydrogen-charged under high temperature and pressure; then, tensile testing was performed at room temperature in air. The yield strength of the 30Mn-0.2C specimen increased with decreasing surface roughness(achieved via polishing), but that of the 30Mn-0.2C-1.5Al specimen was hardly affected by the surface conditions. On the other hand, the tendency of hydrogen embrittlement of the two high-manganese steels was not sensitive to hydrogen charging or surface conditions from the standpoints of elongation and fracture behavior. Based on the EBSD analysis results, the small decrease in elongation of the charged specimens for the Fe-30Mn-0.2C-(1.5Al) high-manganese steels was attributed to the enhanced dislocation pile-up around grain boundaries, caused by hydrogen.

• Journal of Welding and Joining
• /
• v.31 no.6
• /
• pp.65-70
• /
• 2013

In joining Alumina to copper plate by Mo-Mn metallizing process, the effects of the composition of metallizing paste on the bonding strength were investigated. The bonding strength increased with increasing Mn amount in the paste up to 20% but followed by the decrease with addition of Mn. The maximum bonding strength reached 50MPa at 20%Mn when heated to $1550^{\circ}C$ for 60minute. The addition of Si to the metallizing powder increased the bonding strength of the joint by enhancing the mechanical bonding between the Alumina and the metallizing layer due to the decrease of layer viscosity with the addition of $SiO_2$. It is thought that MnO reacted with $Al_2O_3$ to yield $MnAl_2O_4$ spinel, forming a joint.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.271-278
• /
• 2006

Green light emitting $Zn_2SiO_4$Mn and Al co-doped $Zn_2SiO_4$:Mn phosphor were synthesized by a sol-gel method combined with a furnace firing. The luminescent properties of the sample have been investigated. We have found that the phosphor powder with uniform shape show the maximum luminescent intensity when it is prepared with sol-gel method and fired at relatively high temperature ($1100{\sim}1300^{\circ}C$).