• Journal of ILASS-Korea
• /
• v.2 no.1
• /
• pp.29-35
• /
• 1997

Many technologies have been developed to improve diesel emissions or performance, however NOx/PM trade-off occurs because normal methods that reduce NOx emissions tend to increase PM emissions. On the other hand many measures used to control PM emissions tend to increase NOx emissions. Thus, simultaneously controlling both NOx and PM emissions has become a significant challenge for diesel engine manufacturers. As one of the measures, the technology using emulsified fuel has recently become important under the stringent emission regulations of diesel engines. This paper investigates injection characteristics of emulsified fuel and its effect on a combustion performance in a diesel engine. In order to supply emulsified fuel into injection system a mixing unit produced by Harrier is used, then the fuel mixed with water is supplied into injector directly. The spray injected is investigated with a shadowgraph photo system and injection analyzing apparatus, then applied into a diesel engine. Those results showed that the emulsified fuel has an effect on reducing both NOx and PM.

• Proceedings of the KSME Conference
• /
• 2002.08a
• /
• pp.529-532
• /
• 2002

In coflow jets with relatively large size nozzle and low fuel jet velocity, the buoyancy effect arises from the density difference between fuel and air streams. The present study investigated the behavior of such a buoyant cold Jet both numerically and experimentally, especially when the fuel stream has higher density than air. It has been demonstrated that the cold jet has a circular cone shape since upwardly injected fuel jet decelerates and forms a stagnation region, when the fuel jet was composed of propane highly diluted with nitrogen. When the fuel was moderately diluted, numerical results showed the Kelvin-Helmholtz type instability along the mixing layer of the jet. The stagnation height increases nonlihearly with fuel jet velocity with the power of approximately 1.64.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1999.05a
• /
• pp.89-93
• /
• 1999

Experimental studies are conducted to investigate the flame stability and the thermal/fuel NOx formation characteristics of the low calorific value(LCV) gas fuel. Synthetic LCV fuel gas is produced through mixing carbon monoxide, hydrogen, nitrogen and ammonia on the basis that the thermal input of the syngas fuel into a burner is identical to that of natural gas, and then the syngas mixture is fed to and burnt with air on flat flame burner. Flame behaviors are observed to identify flame instability due to blow-off or flash-back when burning the LCV fuel gas at various equivalence ratio conditions. Measurements of NOx in combustion gas are made for comparing thermal and fuel NOx emissions from the LCV syngas combustion with those of the natural gas one, and for analyzing ammonia to NOx conversion mechanism. In addition, the nitrogen dilution of the LCV syngas is preliminarily attempted as a NOx reduction technique.

• Korean Journal of Metals and Materials
• /
• v.47 no.5
• /
• pp.290-296
• /
• 2009

We report on the effects of mixing of powders with various particle sizes on fracture toughness and wear resistance of thermally sprayed WC-10Co-4Cr coating layers fabricated by HVOF (high-velocity oxygen fuel) process. The size and the mixing ratio of powders were changed in order to get high fracture toughness and wear resistance. The mixing of small amount of coarse powders with fine powders resulted in the highest fracture toughness and wear resistance due to the lowest porosity in coating layers.

• Nuclear Engineering and Technology
• /
• v.34 no.5
• /
• pp.482-493
• /
• 2002

The MOX fuel for LWR is fabricated either by direct mechanical blending of UO$_2$ and PuO$_2$ or by two stage mixing. Hence Pu-rich particles, whose Pu concentrations are higher than pellet average one and whose size distribution depends on a specific fabrication method, are inevitably dispersed in MOX pellet. Due to the inhomogeneous microstructure of MOX fuel, the thermal conductivity of LWR MOX fuel scatters from 80 to 100 % of UO$_2$ fuel. This paper describes a mechanistic thermal conductivity model for MOX fuel by considering this inhomogeneous microstructure and presents an explanation for the wide scattering of measured MOX fuel＇s thermal conductivity. The developed model has been incorporated into a KAERI＇s fuel performance code, COSMOS, and then evaluated using the measured in-pile data for MOX fuel. The database used for verification consists of homogeneous MOX fuel at beginning-of-life and inhomogeneous MOX fuel at high turnup. The COSMOS code predicts the thermal behavior of MOX fuel well except for the irradiation test accompanying substantial fission gas release. The over-prediction with substantial fission gas release seems to suggest the need for the introduction of a recovery factor to a term that considers the burnup effect on thermal conductivity.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.225-232
• /
• 2003

With an aim placed on its exploitation on practical injector design, liquid phase mixing due to unlike split triplet impinging element is experimentally investigated by a series of cold tests. Non-reacting kerosene/water spray simulates the kerosene/LOX propellant combination. Measurements of local mixture ratio distribution were made for different injection configurations and different momentum ratios. Mixing and mixing controlled characteristic velocity efficiencies are measured in terms of oxidizer/fuel jet momentum ratio from 0.5 to 8. Extent of mixing and its influence on hot performance are estimated in terms of mixing efficiency and mixing controlled characteristic velocity. Envelope of design locus for optimum mixing quality and corresponding maximum hot performance are proposed. Effects of momentum ratio, orifice diameter ratio and jet velocity ratios are also presented and discussed.

• Applied Chemistry for Engineering
• /
• v.18 no.1
• /
• pp.64-70
• /
• 2007

Preparation and characterization of carbon-slurry fuel with high dispersion have been carried out. Carbon-slurry fuel was obtained by mixing Jet A-1 liquid fuel with appropriate carbon powders and additives. Dispersion of carbon in Jet A-1 was affected by various factors such as mixing temperature, characteristics of carbon powders, and type and amount of additives. Among these factors, the stability of the slurry fuel was most dependent on the type of additive. A variety of additives such as anionic, cationic, and nonionic additives was tested for the dispersion of carbon in Jet A-1. It was found that anionic additives based on sodium salts showed the highest dispersion of carbon-slurry fuels. The degree of dispersion could be monitored by measuring the luminosity.

• Journal of Advanced Marine Engineering and Technology
• /
• v.36 no.7
• /
• pp.885-893
• /
• 2012

DME (Dimethyl ether) is regarded as one of the candidates of alternative fuels for diesel engine, because of its higher cetane number suitable for a compression ignition engine. Also, DME is a simple chemical structure, colorless gas that is easily liquefied and transported. On the other hand, Bunker oil (JIS C heavy oil) has long been used as a basic fuel in marine diesel engines and is the lowest grade fuel oil. In this study, the combustion and emission characteristics were measured experimentally in the direct injection type diesel engine operated with DME and Bunker oil mixed fuel. From our experimental results, it is induced that DME and Bunker oil blended fuel would be an effective fuel which can reduces the concentration of harmful matter in exhaust gases.

• Journal of Advanced Marine Engineering and Technology
• /
• v.21 no.4
• /
• pp.356-363
• /
• 1997

Many research works have been carried out to investigate the factors governing the performance of diesel engine. The area of the study has been focused on reducing both of NOx and smoke because of many difficulties to reduce them simultaneously in diesel engines. One of the efforts is an application of EGR technology to reduce NOx emission, which is very effective, but increases other emissions and makes fuel economy worse. In order to solve the problem, EGR is employed with water emulsified fuel and tested in this paper. Emulsified fuel is produced by centrifugal mixer and the amount of water is controlled by water injector and pulse generator, and EGR rate is controlled with 6-step control valve. The chamber pressure, fuel consumption and emissions are measured with various values of both EGR and water mixing rate, The results show that NOx emission is reduced much rather and smoke is also reduced simultaneously.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.7 no.8
• /
• pp.123-131
• /
• 1999

Natural gas is one of the most promising alternative fuels for automotive vehicles. However, natural gas varies in compositional between the originating fields and may be further modified due to processing and additional mixing. These variations are known to affect engine performance and emissions through changes in fuel metering and combustion characteristics. In the present study, the effect of gas compositions on vehicle performance such as fuel economy, driveability and exhaust emissions was examined. Analysis are made of using 3 types of NGVs which were made by automakers and 6 different fuels which are selected in consideration of the variation in fuel composition on the worldwide market. The results may be utilized to develop natural gas natural gas engine in automaekrs and/or to establish the fuel standard in the refueling stations.