• Journal of the korean Society of Automotive Engineers
• /
• v.2 no.1
• /
• pp.51-60
• /
• 1980

Experiments about engine performance using alcohol-gasoline blend as a fuel are studied. A conventional 4cycle 4cylinder gasoline engine is used. Measurements on torque, output, specific fuel consumption, and emissions are made over ignition timing and mixing ratio. Up to vol. 15% of alcohol, torque and output using alcohol-gasoline blend are almost same with using only gasoline, and specific fuel consumption is improved about 7%. In emissions alcohol-gasoline blend is more effective than gasoline.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.11
• /
• pp.2986-2998
• /
• 1994

• Proceedings of the SAREK Conference
• /
• 2004.11a
• /
• pp.126-126
• /
• 2004

• Journal of the Korean Ceramic Society
• /
• v.31 no.4
• /
• pp.375-380
• /
• 1994

Matrices retaining electrolyte in phosphoric acid fuel cell were prepared with SiC to SiC whisker mixing ratios of 1:0.5, 1:1, 1:1.5, 1:2, 1:3 by tape casting method. When viscosity of the slurry was 5.9 poise and the SiC to SiC whisker mixing ratios were 1:1, 1:1.5, 1:2, the ranges of porosity, acid absorbency and bubble pressure were 80~90%, 2.5~6 and 700~2200 mmH2O, respectively. Those ranges are acceptable for a practical electrolyte-retaining matrix. With increasing the mixing ratio of SiC whisker to SiC, the porosity and the vol.% of large pores in the main pore size distribution which is between 1 and 10 ${\mu}{\textrm}{m}$, increased rapidly. Impedance spectroscopy was measured to know characteristics of matrix inside and contact region of matrix to catalyst layer. When the SiC to SiC whisker mixing ratio was 1:2, hydrogen ions were transported in the matrix most effectively because of high ionic conductivity and low activation energy due to high acid absorbency in spite of high interfacial resistance. The cell current density of the cell made using the matrix was 220 mA/$\textrm{cm}^2$ at 0.7 V.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2012.05a
• /
• pp.378-385
• /
• 2012

Vent mixer can provide main flow directly into a recirculation region downstream of the mixer to enhance fuel-air mixing efficiency. Based on experimental results of three-dimensional velocity, vorticity and turbulent kinetic energy obtained by a stereoscopic PIV method, the performance of the vent mixer was compared with that of the step mixer which was used as a basic model. Thick shear layers of the vent mixer induced the increase of the penetration height. The turbulent kinetic energy mainly distributed along a boundary layer between the main flow and the jet plume. This turbulent field activates mass transfer in a mixing region, leading to the mixing enhancement.

• Journal of Aerospace System Engineering
• /
• v.9 no.2
• /
• pp.34-40
• /
• 2015

Staged combustion cycle engines are well known to have high combustion efficiencies and specific impulse. In this study, design of mixing head part of combustion chamber for 8tonf class staged combustion cycle rocket engine (ES-08) was performed. Structural stability of the mixing head part of the combustion chamber is very important design factor because it is loaded by high temperature and high pressure of fuel and oxidizer as well as by thrust load simultaneously. Uniformity of flow distributions of the propellants to the injectors is also important factor. First, a basic configuration for the ES-08 mixing head part was designed on the basis of the structural design requirements. And then, the structural analyses were performed on the basic configuration as well as some of reinforced configurations. As the structural analyses results, the most stable configuration was selected for the ES-08 mixing head part. In order to examine the uniformity of the flow distributions of the propellants through the manifold of the mixing head, flow analysis was performed based on the selected configuration. The results of the flow analysis showed that the fuel and the oxidizer were uniformly supplied to the injector.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.16 no.4
• /
• pp.57-69
• /
• 2012

The main objective of this study was investigation of natural gas flames in a lean premixed swirl-stabilized dump combustor with an attention focused on the effect of the various fuel-air mixing section geometry on the combustion instability characteristics. The combustor and mixing section length was varied in order to have different acoustic resonance characteristics from 800 to 1800 mm in combustor and 470, 550, 870 mm in mixing section. We observed two dominant instability frequencies in this study. Lower frequencies were associated with a fundamental longitudinal mode of combustor length. Higher frequencies were related to secondary longitudinal mode of coupled with the combustor and mixing section. As a result, combustion instability was strongly affected by acoustic characteristics of combustor and mixing section geometry.

• Resources Recycling
• /
• v.20 no.5
• /
• pp.52-57
• /
• 2011

This study was conducted to examine the possibilities to utilize the mixture of domestic and organic wastes from B-city as a fuel. All types of mixing ratio for uncarried waste, sludge cake, and food waste were found 10 generate heating value with 6,000 kcal/kg, and in case of sludge cake the concentration of toxic substance produced was found to be decreased as air-fuel ratio and temperature were increased. It was noted that toxic gases such as CO, NOx, and SOx were observed below concentration of emission standard, and temperature inside the incinerator was stabilized at 2 of air-fuel ratio and 800$^{\circ}C$. It was observed that a heating value of 6000 kcal/kg generated using RDF(Refuse Derived Fuel) was appropriate to utilize a fuel if a complete combustion was attained.

• Journal of Advanced Marine Engineering and Technology
• /
• v.35 no.1
• /
• pp.53-59
• /
• 2011

The using of diesel engine will be increased in the world for fuel economy. But diesel engine emits harmful emissions such as much NOx, smoke etc. In this study, experiments were performed to investigate the spray characteristics of diesel spray in a common-rail system according to fuel temperature, injection pressure, injection period and fuel viscosity etc. using a high speed video camera. Diesel oil has different spray patten due to injection pressure and injection period in a common-rail system. A Filter pressure was influenced by fuel temperature which was turned to fuel viscosity related to a fluid flowing. The effect of the bio-diesel fuel mixing ratio on the spray and atomization characteristics was also investigated at various experimental conditions. It shows that the droplet atomization characteristics of bio-diesel fuel showed deteriorated results as the mixing ratio of biodiesel increased because of the high viscosity.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.5
• /
• pp.39-46
• /
• 2006

The fuel cell is one of promising environment-friendly energy sources for the next generation. The bipolar plate is a major component of the PEM fuel cell stack, which takes a large portion of stack cost. In this study, as alternative materials for bipolar plate of PEM fuel cells, graphite composites were fabricated by compression molding. Graphite particles mixed with epoxy resin were used as the main substance to provide electric conductivity To achieve desired electrical properties, specimens made with different mixing ratio, processing pressure and temperature were tested. To increase mechanical strength, one or two layers of woven carbon fabric were added to the graphite and resin composite. Thus, the composite material was consisted of three phases: graphite particles, carbon fabric, and epoxy resin. By increasing mixing ratio of graphite, fabricated pressure and process temperature, the electric conductivity of the composite was improved. The results of tensile test showed that the tensile strength of the two-phase graphite composite was about 4MPa, and that of three-phase composite was increased to 57MPa. As surface properties, contact an91e and surface roughness were tested. Graphite composites showed contact angles higher than $90^{\circ}$, which mean low surface energy. The average surface roughness of the composite specimens was $0.96{\mu}m$.