• Journal of the Korean Society of Radiology
• /
• v.11 no.5
• /
• pp.297-302
• /
• 2017

Recently, building materials and air purification filters with eco-friendly charcoal are actively studying to reduce the concentration of radon gas in indoor air. In this study, radon reduction performance was assessed by designing and producing new panel-type activated carbon filter that can be handled more efficiently than conventional charcoal filters, which can reduce radon gas. For the fabrication of our panel-type activated carbon filter, first the pressed molding product after mixing activated carbon powder and polyurethane. Then, through diamond cutting, the activated carbon filter of 2 mm, 4 mm and 6 mm thickness were fabricated. To investigate the physical characteristics of the fabricated activated carbon filter, a surface area and flexural strength measurement was performed. In addition, to evaluate the reduction performance of radon gas in indoor, the radon concentration of before and after the filter passes from a constant amount of air flow using three acrylic chambers was measured, respectively. As a result, the surface area of the fabricated activated carbon was approximately $1,008m^2/g$ showing similar value to conventional products. Also, the flexural load was found to have three times higher value than the gypsum board with 435 N. Finally, the radon reduction efficiency from indoor gas improved as the thickness of the activated carbon increases, resulting in an excellent radon removal rate of more than 90 % in the 6 mm thick filter. From the experimental results, the panel-type activated carbon is considered to be available as an eco-friendly building material to reduce radon gas in an enclosed indoor environment.

• Journal of the Korean Society of Groundwater Environment
• /
• v.4 no.3
• /
• pp.130-143
• /
• 1997

To investigate geochemical characteristics and the sources of the dissolved ion species in the river water in the Han river drainage basin, samples were collected at 60 sites from the Han river drainage basin. The data for. pH, conductivity, TDS (total dissolved solid), temperature, and concentrations of dissloved ions were obtained as follows : (1) The geochemical characteristics of the surface water in the South and North Han river drainage basins are mainly controlled by bed rock geology in the drainage basin and in the main stream of the Han river considerably affected by anthropogenic pollution. The South Han river water samples have high concentrations of $Ca^{2＋}$ (ave. 15.42 ppm), $Mg^{2＋}$ (ave. 2.74 ppm), HC $O_3$$^{[-10]}$ (ave. 51.9 ppm), which evidently indicates that the bed rock geology in a limestone area mainly controls the surface water chemistry. The concentration of S $O_4$$^{2-}$ is remarkably high (SHR10-2 : 129.9 ppm) because of acid mine drainage from the metal and coal mines in the upper reaches of the South Han river. (2) The South Han river and the North Han river join the Han river. in the Yangsuri, Kyounggido and flow through Seoul metropolitan city. The mixing ratio is about 60:40 at the meeting point (sample number HRl0). (3) The result of factor analysis suggests that the pollution factor accounts for about 79% and the bed rock type factor accounts for about 7% of the data variation. This means that the geochemical characteristics of the Han river water mainly controlled by anthropogenic pollution in the South Han river and main stream of the Han river drainage basin. (4) The chemical data for four tributaries such as the Wangsukcheon, the Tancheon, the Zunuangcheon, and the Anyangcheon show that the concentration of pollution elements such as N $O_2$, C $l^{－}$, P $O_4$$^{3-}$, S $O_4$$^{2-}$ and Mn are high due to municipal waste disposal.

• Journal of the Korean earth science society
• /
• v.22 no.5
• /
• pp.377-387
• /
• 2001

In order to elucidate sedimentation processes and depositional environments in transitional area between continental shelf and coastal zone, sedimentologic study has been done with 84 surface sediments sampled in nearshore/offshore off the mid-western coast of the Korean Peninsula for 3 years (1996${\sim}$1999). The surface sediment can be classified into 4 facies (gravelly sand, sand, silty sand and sandy silt). Mean grain size, sorting, skewenss and kurtosis varies -0.39${\sim}7.82{\Phi}$, 0.36${\sim}4.68{\Phi}$, -0.38${\sim}$0.86, -1.56${\sim}$3.43, respectively. The textural parameters show a finer-grained and poorly-sorted trend shoreward, northward and southward from the central part of the study area. The positively-skewed distribution and relationship of each textural parameters indicate a tide-dominated depositional environment. According to C/M diagram, there are 3 different domains (mode A, B, C) of sediment transport mode. The northern part is characterized by bedload transport (mode A) and represents co-influence of wave and tide, whereas domain C in the southern part is controlled by uniform suspension transport (mode C), correlating with sandy-silt area. In the broad middle area, transport processes are complex (the mixture of bedload, graded suspension and uniform suspension; mode B). Hence, the subdivision depositional environments of this study area may be classified by 3 depositional environments dependent on the interplay of sediment supplies from river, relict sediments and hydrologic conditions. In results, the nearshore and offshore areas are thus characterized as a mixing zone between coastal terrigenous sediments and relict sediments in the continental shelf by complex processes (tide, wave and river flow). These sedimentation processes play an important role in producing distinct sedimentologic features in the transitional zone linking coastal and shelfal areas.

• Economic and Environmental Geology
• /
• v.34 no.4
• /
• pp.329-343
• /
• 2001

The deep environment and geochemical evolution of the Bugok geothennal waters, located in the Kyeongnam Province, was re-interpreted based on the hydrochemical and isotopic data published by Yun et al. (1998). The geothermal waters of the Bugok area is geochemically divided into three groups; Geothennal water I, II and III groups. Groups I and II are geochemically similar; high temperature (55.2-77.2$^{\circ}$C) and chemically belonging to Na-S04 types. However, pH and Eh values are a little different each other and Group II water is highly enriched in S04 compared to Group I water. Group III water, occurring from peripheral sites of the central part of the geothennal waters, shows temperature range of 29.3 to 47.0$^{\circ}$C and belongs to $Na-HCO_3-S0_4$ types. The deep environment and geochemical evolution of the Bugok geothennal waters, showing the diversity of geochemistry, can be interpreted as follows; I) Descending to great depth of meteoric waters that originated at high elevation and reacting with sediments and/or granites in depth. The $S0_4$ concentration of the waters has been increased by the dissolution of sulfate minerals in sediments. 2) During the continuous descending, the waters has met with the reduction environment, producing the $H_2S$ gas due to sulfate reduction. The waters has been heated up to 130$^{\circ}$C and the extent of water-rock reaction was increased. At this point, pH of waters are increased, S04 concentration decreased and calcite precipitated, therefore, the waters show the $Na-S0_4$ type. 3) Ascending of the geothennal waters along the flow path of fluids and mixing with less-deeply circulated waters. The $S0_4$ concentration is re-increased due to the oxidation of $H_2S$ gas and/or sulfide minerals in sediments. During continuous ascending, these geothennal waters are mixed with shallow groundwater.

• The Journal of the Petrological Society of Korea
• /
• v.28 no.4
• /
• pp.251-277
• /
• 2019

The Gogunsan Archipelago is composed of two island groups; the first group includes Mal-do, Myeong-do, Gwangdae-do, and Bangchuk-do islands consisting of Neoproterozoic rocks, and the second group includes Yami-do, Sinsi-do, Muneo-do, Jangja-do, and Seonyu-do islands consisting of Cretaceous rocks. The first group mainly consists of the Bangchuk formation which can be divided into two layers; the lower layer was more deformed than the upper layer. The former was intruded by mafic and felsic volcanic rocks formed in the volcanic arc tectonic setting 930-890 Ma and the latter was deposited ca. 825-800 Ma. In these islands, large scale folds with east-west fold axes were beautifully formed; the Maldo island fold was designated as natural monument and large scale beautiful chevron fold was developed on the Gwangdae-do island. In addition, there are unique zebra-shaped outcrop formed by a mixing of basic and acidic magma and Independent Gate shaped outcrop formed by coastal erosion. On the other hand, the Yami-do, Sinsi-do, Muneo-do, Jangja-do and Seonyu-do islands consist of 92-91Ma Cretaceous volcanic rocks and, in Sinsi-do island, the Nanshan formation deposited ca. 92 Ma. These Cretaceous volcanic rocks formed by melting of the continental crust by the heat supplied from the uplifting mantle due to the extension caused by a retreat of subducting ocean slab. Yami-do and Sinsi-do islands are composed of rhyolite. In Yami-do island, bands with vertical joint formed by cooling of the bottom part of the lava, are shown. In Sinsi-do island, large-scale vertical joints formed by cooling of lava flow, were developed. The Jangja-bong of Jangja-do island and Mangju-bong of Seonyu-do island are composed of brecciated rhyolite and formed a ring shaped archipelago contributing to the development of marine culture by providing natural harbor condition. They also provide beautiful views including 'Seonyu 8 views' along with other islands. As mentioned above, the Gogunsan archipelago is rich in geoheritages and associated cultural and historical resources, making it worth as a National Geopark.

• Journal of the Korean Society for Marine Environment & Energy
• /
• v.12 no.1
• /
• pp.35-46
• /
• 2009

In order to investigate spatial and temporal distributional characteristics of major water qualities in the Saemangeum area during the Saemangeum dike construction, salinity, COD, dissolved nutrients(DIN, Silicate) and heavy metals were analyzed from the surface water collected in April, May, August and November 2002. The overall value of Salinity, COD, DIN, and silicate in surface waters were in the range of $13.08{\sim}31.96\;psu$, $0.12{\sim}3.43\;mg/L$, $0.001{\sim}2.638\;mg/L$, and $0.010{\sim}3.181\;mg/L$, respectively. The COD and DIN in each survey showed the highest concentration at the mouth of Mangyeong river estuary(St. 1) where freshwater flow into the Saemangeum area. The concentrations of nutrients were high in the inner part of the Saemangeum dike with low-salinity, and low nutrients in the outer part of the dike with high-salinity, which strongly indicated that concentrations were adjusted by physical mixing. The ranges of dissolved metals and acid-soluble Hg in surface seawater were $0.006{\sim}0.115{\mu}g/L$ for Co, $0.26{\sim}0.114{\mu}g/L$ for Ni, $0.14{\sim}0.93{\mu}g/L$ for Cu, $0.04{\sim}0.53{\mu}g/L$ for Zn, $0.010{\sim}0.043{\mu}g/L$ for Cd, $0.010{\sim}0.795{\mu}g/L$ for Pb, and $0.25{\sim}4.16{\mu}g/L$ for Hg. The highest concentrations of some metals except for Cd were found at the estuary(Sts. 1 or 3). In most cases, a decreasing order of metal concentrations towards open sea(low-salinity$\rightarrow$high-salinity) was observed and showed positive relationship with DIN and silicate caused by land base pollutants input. On the other hand, due to Cd desorption from suspended solids in saline water, dissolved Cd concentrations were high in high-salinity area and low in low-salinity. In November, Co, Zn, Cu and Pb were relatively high in the northern area of the outer-side of Saemangeum, which was only influenced by the Geum river discharge. The concentrations of most dissolved metals of this study were lower than those of the past data in this area, but higher than those in Lena river estuary under the pristine environment.

• Economic and Environmental Geology
• /
• v.48 no.5
• /
• pp.409-420
• /
• 2015

The Sangdae-ri riverside around Musimcheon stream, flowing through Gadeok-myon of Cheongju City, is one of the representative strawberry fields employing water curtain cultivation (WCC) in Korea. In this area, annual groundwater use for WCC has been calculated by a few methods. On the assumption that all the water flowing through the final ditch may be mostly composed of groundwater, the discharge rate in it can be used as a good proxy for assessing the groundwater use. However, in the study area, the final ditch was set up in an unpaved state near and parallel to Musimcheon stream. Under such circumstances, the drainwater is likely to be influenced by infiltration and/or inflow of nearby stream. Hence, we examined whether or not stream water has influenced water flowing out through the final ditch in respect of ion concentrations or field parameters such as T, pH and electrical conductivity (EC) values. The period of measuring field parameters and sample collection was from February 2012 through February 2015. The drainwater in the final ditch did not show the average quality of groundwater, but similar quality of stream water in respect of pH, EC, ion contents and water type. From this, it is suggested that measuring the flow rate of the final ditch should not be directly used for assessing groundwater use in the study area. In addition, because of its sensitivity to ambient temperature, water temperature proved not to be appropriate for estimating the interaction between ditch and stream. For accuracy, additional methods will be needed to calculate mixing ratios between stream and ground water within drainage system.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.101-111
• /
• 2016

It is possible that aggregates add on to geopolymer based fly ash to mix mortar and concrete like cement. This is necessary to evaluate mineral composition, particle shape, surface, size distribution, density and absorption ratio for fine aggregates due to few detailed research to examine influence of fine aggregates properties on unhardened geopolymer concrete. In this research, used two different fine aggregates, Jumunjin sand(having quartz, mica, feldspar, pyroxene in mineral composition, more than 96% of total size between -0.60 and +0.30mm, angular shape and rough surface) and ISO sand(having almost all quartz in mineral composition, more than 51% size between -1.40 and +0.60mm, simultaneously varied size distribution, spherical shape and smooth surface). After an experimental result of the varied ratio of Si/Al=1.0-4.1 geopolymer paste, mix proportion respectively applied Si/Al=1.5 having the highest compressive strength to mortar and Si/Al=3.5 having the highest consistency to concrete. Geopolymer mortar by mixing with Jumunjin and ISO sand in varied range of 20-50wt.% showed flow size increase between 69.5 and 112.0mm, between 70.5 and 126.0mm respectively. Geopolymer concrete at an addition of 77wt.% of total aggregates ratio showed that average compressive strength was 32MPa and the consistency was favorable to molding. Since ISO sand observing varied size distribution, spherical shape, smooth surface, low absorption ratio resulted in advantageous properties on consistency of geopolymer, geopolymer concrete can be suitable for using the fine aggregates similar to ISO sand.

• Journal of the Korean Applied Science and Technology
• /
• v.35 no.4
• /
• pp.985-994
• /
• 2018

Bio-heavy oil for power generation is a product made by mixing animal fat, vegetable oil and fatty acid methyl ester or its residues and is being used as steam heavy fuel(B-C) for power generation in Korea. However, if the fuel supply system of the fuel pump, the flow pump, the injector, etc., which is transferred to the boiler of the generator due to the composition of the raw material of the bio-heavy oi, causes abrasive wear, it can cause serious damage. Therefore, this study evaluates the fuel characteristics and lubricity properties of various raw materials of bio-heavy oil for power generation, and suggests fuel composition of biofuel for power generation to reduce frictional wear of generator. The average value of lubricity (HFRR abrasion) for bio-heavy oil feedstocks for power generation is $137{\mu}m$, and it varies from $60{\mu}m$ to $214{\mu}m$ depending on the raw materials. The order of lubricity is Oleo pitch> BD pitch> CNSL> Animal fat> RBDPO> PAO> Dark oil> Food waste oil. The average lubricity for the five bio-heavy oil samples is $151{\mu}m$ and the distribution is $101{\mu}m$ to $185{\mu}m$. The order of lubricity is Fuel 1> Fuel 3> Fuel 4> Fuel 2> Fuel 5. Bio-heavy oil samples (average $151{\mu}m$) show lower lubricity than heavy oil C ($128{\mu}m$). It is believed that bio-heavy oil for power generation is composed of fatty acid material, which is lower in paraffin and aromatics content than heavy oil(B-C) and has a low viscosity and high acid value, resulting in inhibition of the formation of lubricating film by acidic component. Therefore, in order to reduce friction and abrasion, it is expected to increase the lubrication of fuel when it contains more than 60% Oleo pitch and BD pitch as raw materials of bio-heavy oil for power generation.

• Proceedings of The Korean Society of Agricultural and Forest Meteorology Conference
• /
• 2013.11a
• /
• pp.23-24
• /
• 2013

Micrometeorological fluxes measured over a tall forest in a complex terrain are difficult to interpret. $CO_2$ storage often makes significant contributions to net ecosystem exchange of $CO_2$ (NEE) in early morning and during nighttime due to calm and stable conditions. We measured the above-canopy $CO_2$ flux along with its concentration profiles at eight levels within and above the canopy to evaluate $CO_2$ storage term. Our question is whether or not the $CO_2$ storage term can be estimated accurately from a single level measurement of $CO_2$ concentration in a complex terrain. Our objectives are (1) to document vertical profiles of $CO_2$ concentration and (2) to compare the diurnal and seasonal variations of $CO_2$ storages estimated from single and multi-level $CO_2$ concentration data. Seasonally averaged Diurnal variations of $CO_2$ concentration ranged from 398 to 455 ppm near the forest floor at 0.1 m whereas they ranged from 364 to 395 ppm at 40 m in the atmosphere. The diurnal variation of vertical profiles of $CO_2$ concentration shows very interesting features with season. At all eight levels, diurnal variation of $CO_2$ concentration showed little change in winter. In spring, the diurnal variations of $CO_2$ concentration at 8 levels showed three distinct groups of layers with height: the first layer: 0.1m (near surface), second layer: 1.0 m and 4.0m (below canopy) and the third layer: 7.4m to 40.7 m (near canopy and above). In summer, these three groups of layers were further separated with larger variations whereas such distinction became smaller in fall. The diurnal variation of $CO_2$ concentration in the first three layers near surface always showed higher concentration with larger variability. Typically, $CO_2$ concentration showed peaks in early morning and in the evening. After the evening peak, $CO_2$ concentration gradually increased except for those near the surface (i.e., 0.1, 1.0 and 4.0 m) where the concentrations actually decreased. We suspect that this could be attributed to the drainage flow of $CO_2$ along the hill slope from the headwater to downstream, which is not taken into account for net ecosystem $CO_2$ exchange. In comparison to the results of other studies, the distinct and different vertical structures of $CO_2$ concentrations observed at our site may be due to complex terrain and weak turbulent mixing under calm conditions at the site. The annual mean of diurnal variation of $CO_2$ storage flux from single level ranged from -0.6 to $0.9{\mu}mol\;m^{-2}s^{-1}$ and from multi-level from -1.2 to $1.0{\mu}\;{\mu}mol\;m^{-2}s^{-1}$. When compared against the results from the multi-level concentrations, the storage flux estimated from a single-level concentration was generally adequate except for specific hours near sunrise and sunset. Further details and their implication will be discussed in the presentation.