• Asian Journal of Turfgrass Science
• /
• v.24 no.2
• /
• pp.205-210
• /
• 2010

This study was conducted to investigate the effect of the mixed ratio of the soil amendments, peat, humate, peatmoss and zeolite, on the soil physicochemical properties. The mixed ratios of soil amendments were 0%, 3%, 5%, 7% and 10% (v/v) incorporated with sand which met to the USGA (United State of Golf Association) recommendation. It was measured pH, EC and CEC as a chemical properties. Porosity, capillary porosity, air-filled porosity, bulk density and hydraulic conductivity were also measured to analyze the changes of physical properties. Chemical properties were significantly different by mixture ratios of peat, humate, peatmoss and zeolite. When the results were applied to the USGA standard of the soil physical properties, the optimum mixture ratios of peat, humate and peatmoss were 5%, 3% and 7%, respectively. Air-filled porosity was factor involved in soil physical properties by blending with soil amendments and it was affected on volume of porosity and hydraulic conductivity. To analyze the corelation of mixture ratio versus to physical characters, the ratio of peat and peatmoss was significantly related to capillary porosity and hydraulic conductivity (P<0.05), that of humate hydraulic conductivity (P<0.01), and that of zeolite air-filled porosity and volume of porosity (P<0.05). These results could be used as a basic data for construction USGA sand green.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.4 no.2
• /
• pp.187-194
• /
• 2016

In this research, the influence of low-quality aggregate on engineering properties of concrete was experimentally evaluated. From a series of experiment, the results can be summarized as follow: first, the low-quality aggregate in concrete mixture caused up to 83% of decreased slump. For air content, low-quality aggregate increased air content of concrete mixture. Especially, when sea sand was used, because of the narrow gradation with small size, the air content was significantly increased. The compressive strength of concrete mixtures with low-quality aggregates were decreased up to 29% while some cases showed slightly increased compressive strength at early age. Additionally, the concrete mixture mixed with the exploded debris as a coarse aggregate showed approximately 5 to 20% of decreased compressive strength comparing with high-quality of manufacturing rock. In summary, because of the decreased workability of concrete mixture mixed with low-quality aggregates such as exploded debris, clay, and sea sand, it is concerned that worse quality of the ready mixed concrete, produced with the extra water to compensate the decreased workability.

• Journal of Korea Soil Environment Society
• /
• v.3 no.3
• /
• pp.63-74
• /
• 1998

In the study, the feasibility of deposit soil in river and stream bed as a subsitute for conventional plant soil was investigated through the analysis of soil characteristics and germination/growth rate for 75 days. Proper mixtures among sediments from various places were compared to optimize the germination and growth rate of plant in the ratio of 2 : 1 and 3 : 1 (sand : deposit). From the results, it could be concluded that the sediment mixed 3 : 1 showed most favorable germination and growth conditions for pansy and the sediment containing enough amount of silt and clay components showed most favorable conditions for marigold. Consequently, the feasibility of sediments as a substitutional plant soil was evaluated to be high, once the sediments were properly mixed for each specific plant.

• Journal of the Korean Geosynthetics Society
• /
• v.8 no.2
• /
• pp.41-46
• /
• 2009

In this paper, a series of model tests were performed in laboratory to evaluate promoting consolidation of compaction pile methods for soft ground improvement. For the model tests, composite soil samples that have 10% replacement area ratio were prepared by using sand, gravel, and sandy gravel for the materials of compaction piles. After loading to each composite soil sample, the excess pore pressure dissipation and settlement were investigated. In addition, the behavior of clay mixed with each compaction pile was also monitored at the end of consolidation to evaluate clogging phenomenon. As a test result, the effects for decreasing settlement and promoting consolidation by GCP were prominent, and the mixed clay was not monitored in all of the three compaction piles.

• Clean Technology
• /
• v.8 no.2
• /
• pp.67-76
• /
• 2002

Dewatered sludge of 400,000t/y from water treatment plants in Korea is being disposed through landfill and ocean dumping. However, the disposal is posing more and more serious environmental problems at the same time not only because of landfill site shortage in municipal suburbs, but because of the concern it will contaminate the oceans. In this study, the research on utilizing the sludge dried by flash dryer as covering soil in the landfill sites was carried out to solve these problems on environmental affinity. Both dewatered and dried sludge were exposed to the natural condition and observed according to the atmospheric changes. An experiment of soil engineering characteristics of the dried sludge and tests on mixed sludge(silty sandy soil : dried sludge = 10:90 ~ 30:70) such as particle size distribution, liquid and plastic limit, moisture content, specific gravity and compaction test were carried out. According to the compaction test, the compaction was confirmed as the optimum water content ratio was observed in the condition of SM-silty sand of particle size distribution, NP of liquid and plastic limit, 101.4% of moisture content, 2.04~2.12 of specific gravity. The results showed that dried sludges mixed with at least 30% of natural soil could be used as daily covering soil in the landfill sites.

• Journal of Industrial Technology
• /
• v.27 no.A
• /
• pp.111-120
• /
• 2007

This paper is results of experimental research on the effect of application of similarity related to permeability of soil on the consolidation behavior as centrifuge modeling of consolidation is performed with the centrifuge model facility. In this research, the permeability of soil was controlled by changing the viscosity of porewater as the mixed water with glycerin was used during the centrifuge model experiments. The effect of drainage path on consolidation was investigated by installing the vertical drains. A serise of centrifuge model tests with conditions of single vertical and radial horizontal drainage were carried out. Kaolinite and Jumunjin standard sand were used as soft clay and surcharges respectively during tests. For testing condition of single vertical drainage considering similarity of permeability, it was found that consolidation with mixed porewater with glycerin was delayed in comparisons sons with test results with water only. For conditions of horizontal drainage with vertical drains, a low permeability by changing the viscosity of pore water resulted in delayed degree of consolidation at an initial stage of consolidation. But, it predicted not much differences in settlement as long as the consolidation time was sufficiently long enough to finish consolidation. Consequently, it was found that similarity in permeability should be considered to be critical for the case of centrifuge model experiments related to consolidation with long drainage path.

• Computers and Concrete
• /
• v.24 no.1
• /
• pp.1-6
• /
• 2019

Within the scope of this study, the foam solution was prepared by properly mixing sulfonate based foam agent with water. Furthermore, this solution was mixed with the mixture of fine sand, cement, and water to produce foamed concrete. The mixture ratios which are the percentage of foam solution used in foam concrete were chosen as 0, 20, 40 and 60% by vol. After these groups reached 28 days of strength, they were heated to 20, 100, 400 and $700^{\circ}C$ respectively. Afterward, high-temperature effects on the foamed concrete were obtained by employing physical and mechanical properties tests. Additionally, SEM (scanning electron microscope) and EDX (energy-dispersive X-ray spectroscopy) tests were employed to analyze the microstructure, and ${\mu}-CT$ (micro computed tomography) images were used to reconstruct 3-D models of the heat-treated specimens. Then, these models are analyzed to examine the void structures and the changes in these structures due to the high temperatures. The study has shown that the void structures reduce the high-temperature effects and the foam solution could be mixed with concrete up to 40 % by vol. where the high strength of foamed concrete is non-mandatory.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2020.11a
• /
• pp.94-95
• /
• 2020

Oyster shells are characterized by coarse and coarse grains, but similar in strength to sand, and egg shells are fine grains but weak in strength. In terms of supply and demand of raw materials, oyster shells can be supplied only in limited periods and regions in winter and south coast of the year, but egg shells have the advantage of being able to supply and supply nationwide 365 days. This study aims to study the change in strength characteristics by mixing oyster shell powder and egg shell powder with the same particle size and mixing up to 150%. The conclusions of the flexural and compressive strength tests of mortar mixed with oyster shell powder and egg shell powder are as follows. The 7-day flexural and compressive strength with ESP added and the 3-day flexural and compressive strength with OSP added were similar, which is thought to be because the strength of OSP is higher than that of ESP.

• Journal of the Korean earth science society
• /
• v.37 no.4
• /
• pp.218-229
• /
• 2016

The bedform stability diagram indicates the shape and size of bedforms that will occur to a given grain size and flow velocity. The diagram has been constructed from experimental data which have been mostly acquired by flume experiments. Generally, the flume experiments have been performed on well sorted sediments with unimodal grain size distribution, in order to understand relationship between grain size and flow velocity. According to the diagram, a ripple structure initiates to be formed from lower flow regime flat bed, as the flow velocity increases on the surface of fine-sand or medium-sand sediments. This study aims to verify that the experimental result of bedform stability diagram will be reproduced in our flume experimental systems, and also to confirm that the result is consistent not only on well-sorted sand sediments but also on poorly-sorted sand sediments with bimodal grain size distribution. The experimental results in this study show that initiation of 2D or 3D ripple structure on poorly-sorted sand sediments requires higher flow velocity and shear stress than those for initiation of the structure on well-sorted sand sediments. In general, carbonate sediments are characterized by poor sorting due to inactive hydraulic sorting and bimodal grain size distribution with allochems and matrices. The results suggest that the carbonate depositional system possibly need a higher flow velocity for initial formation of 2D or 3D bedform structures. The reason might be the fact that pulling off and lifting of a grain in poorly sorted sediments require more energy due to sorting, friction, stabilization, armour effects, and their complex interaction. This preliminary study warrants additional experiments under various conditions and more accurate analysis on the relationship between formation of bedforms and grain size distribution.

• Journal of the Korean Geotechnical Society
• /
• v.29 no.4
• /
• pp.45-56
• /
• 2013

In this study, a blast furnace slag with latent hydraulic property is used to cement granular soils without using Portland cement. When the blast furnace slag reacts with an alkaline activator, it can cement soils. The effect of amounts of blast furnace slag and types of alkaline activator on soil strength was investigated for resource recycling. Four different amounts of slag and six different activators (two naturals and four chemicals) were used for preparing specimens. The specimens were air-cured for 3 or 7 days and then tested for unconfined compressive strength (UCS). The UCS of cemented sand with slag increased, in the order of specimens mixed with potassium carbonate, calcium hydroxide, sodium hydroxide and potassium hydroxide. Chemical alkaline activator was better than natural alkaline activator. The maximum UCS of 3-days cured specimens was 3 MPa for 16% of slag with potassium hydroxide, which corresponded to 37% of one with 16% of high-early strength portland cement. As the amount of slag increased, the UCS and dry density of a specimen increased for all alkaline activator cases. As the curing time increased from 3 days to 7 days, the UCS increased up to 97%. C-S-H hydrates were found in the cemented specimens from XRD analyses. Cement hydrates were more generated with increasing amount of slag and they surrounded sand particles, which resulted in higher density.