• Clean Technology
• /
• v.21 no.3
• /
• pp.184-190
• /
• 2015

Most of LNT catalysts use noble metals such as Pt for low temperature NO_x oxidation but there is an economic weakness. For the purpose of overcoming this, this study is to develop DeNO_x catalyst for LNT excluding PGM (platinum group metal) such as Pt, Pd, Rh, etc. To do so, Al/Co/Ni catalyst selected as a preliminary test is used to study fundamental property and NO_x’s conversion according to calcined temperature. Ultimately, that is, Al/Co/Ni mixed metal oxide which does not use PGM is selected and physicochemical characterization is performed by way of XRD, EDS, SEM, BET and ramp test and NO_x conversion is also analyzed. This study shows that all samples consist of mixed oxides of spinel structure of Co₂AlO₄ and NiAl₂O₄ and have enough pore volume and size for redox. But as a result of NH₃-TPD test, it is desired that calcined temperature needs to be maintained at 700 ℃ or lower. Also only samples which are processed under 500 ℃ satisfied NO and NO_x conversion simultaneously through ramp test. Based on this study’s results, optimum calcined temperature for Al/Co/Ni=1.0/2.5/0.3 mixed metal oxide catalyst is 500 ℃.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.4
• /
• pp.323-330
• /
• 2017

Ash remaining after coal combustion was used as a catalyst support for tar steam reforming with various proportions of $Al_2O_3$ added for higher reforming efficiency. At a constant Ni content of 12 wt%, a coal ash and $Al_2O_3$ were mixed at a ratio of 5:5, 7:3, 9:1. As a result, the catalytic activity for toluene steam reforming was improved by adding $Al_2O_3$ at $500-600^{\circ}C$. The catalysts with ratio 7:3 and 5:5 reached toluene conversion of 100% above $700^{\circ}C$. When comparing the catalysts in which the coal ash and $Al_2O_3$ mixed at a ratio of 5:5 and 7:3 with the Ni/Al catalyst, it was concluded that this coal ash catalyst has efficient catalytic performance.

• Journal of Korean Society for Atmospheric Environment
• /
• v.1 no.1
• /
• pp.43-51
• /
• 1985

This study is concerned with the oxidation of carbon monoxide on platinum and platinum-palladium catalysts. Catalysts were made by the impregnation method and flow reactor was used in the catalytic reaction. As for the mixed gases, carbon monoxide concentration varied from 1 to 4% and that of oxygen from 1 to 4%. $N_2$ was used as carrier gas and GHSV varied from 24, 000 $h^{-1} to 60, h^{-1}$. The temperature range was from 200 to $600^\circ$C. It was also taken into consideration that the heat and mass transfer resistance of our catalysts was negligible in the study. Experimental results showed that platinum-palladium catalyst was about 1.5-3.9% superior to platinum catalyst in conversion yield. When we used platinum-palladium catalyst, we observed that carbon monoxide oxidation was found to be 1 st order with respect to carbon monoxide concentration. Activation energy of the catalyst was 23.5 kcal/mol.

• Journal of the Korean Wood Science and Technology
• /
• v.30 no.3
• /
• pp.66-74
• /
• 2002

The effects of phenol during ethylene carbonate (EC) liquefaction of pine bark in the presence of methanesulfonic acid (MSA) as a catalyst were investigated. Liquefaction of pine bark using EC in the presence of acid catalyst was very difficult in comparison to wood. Mixing ethylene glycol (EG) with EC improved the liquefaction process, but the maximum liquefaction yield did not exceed 78%. Mixing 20~30% phenol with EC was very effective for the liquefaction and the residue was remarkably decreased. More than 95% of liquefaction was achieved when about 30% phenol was mixed with EC. The reaction conditions, such as catalyst concentration, liquefaction temperature and time, type of catalyst and liquefying agent, had a great influence on the liquefaction process. The results of the average molecular weights and the amount of combined phenols for the liquefied products indicated that sulfuric acid (SA) causes high condensation reactions compared to MSA.

• Journal of the Korean Applied Science and Technology
• /
• v.33 no.2
• /
• pp.401-410
• /
• 2016

The $Pt-Sn/Al_2O_3$ catalysts mixed with metal oxides for propane dehydrogenation were studied. $Cu-Mn/{\gamma}-Al_2O_3$, $Ni-Mn/{\gamma}-Al_2O_3$, $Cu/{\alpha}-Al_2O_3$ was prepared and mixed with $Pt-Sn/Al_2O_3$ to measure the activity for propane dehydrogenation. As standard sample, $Pt-Sn/Al_2O_3$ catalyst mixed with glassbead was adopted. In the case of catalytic activity test after non-reductive pretreatment of catalyst and metal oxide, $Pt-Sn/Al_2O_3$ mixed with $Cu-Mn/{\gamma}-Al_2O_3$ showed higher conversion of 15% and similar selectivity at $576.5^{\circ}C$, compared to conversion of 8% in standard sample. In the case of catalytic activity test after reductive pretreatment of catalyst and metal oxde, $Cu/{\alpha}-Al_2O_3$ showed higer yield than standard sample. But, increase of yield of most of samples after reductive pretreatment was not significant, so it was found that lattice oxygen of $Cu-Mn/{\gamma}-Al_2O_3$ is effective to propane dehydrogenation.

• Journal of the Korean Applied Science and Technology
• /
• v.30 no.4
• /
• pp.649-655
• /
• 2013

Methanol was directly produced by the partial oxidation of methane with perovskite and mixed oxide catalysts. Perovskite ($ABO_3$) catalysts were prepared by the malic acid method with changing A and B site components. Three-component mixed oxide catalysts that have Mo and Bi as a main component were prepared by the co-precipitation method. Among the perovskite catalysts, $SrCrO_3$ showed the highest methanol selectivity of 11% at $400^{\circ}C$. For the three-component mixed oxide catalysts, there were no remarkable changes in methane conversion. Among the mixed oxide catalysts, Mo-Bi-Cr mixed oxide catalyst showed the highest methanol selectivity of 15.3% at $400^{\circ}C$. The catalytic activity and methanol selectivity of the three-component mixed oxide catalysts were directly proportional to the surface area of the catalysts.

• Environmental Engineering Research
• /
• v.24 no.2
• /
• pp.324-330
• /
• 2019

To recycle raw fly ash (RFA), a waste from thermal power plants, it was used to prepare solid catalysts which have many advantages compared with homogenous catalysts. When biodiesel was produced from soybean oil using RFA, only 1.2% of biodiesel conversion was obtained. A metal hydroxide, NaOH, KOH or $Ca(OH)_2$, was mixed with the acid-treated fly ash (ATFA), and the mixture was calcined at $700^{\circ}C$ for 3 h to prepare the solid catalyst. The solid catalyst prepared by mixing ATFA with NaOH, designated as SC-Na, showed a better performance than those prepared by mixing ATFA with KOH or $Ca(OH)_2$, respectively. The optimal mass ratio of ATFA with NaOH was 1:3, at which the proportion of $Na_2O$ increased to 60.2% in SC-Na, and 97.8% of biodiesel conversion was achieved under optimal reaction conditions (2 w% SC-Na relative to oil and 5 mL-methanol/g-oil at $50^{\circ}C$ for 4 h). Finally, a batch operation was repeatedly carried out to test the feasibility of reusing the solid catalyst, and more than 96% biodiesel conversion was stably achieved for the third round of operations. This study shows that RFA was successfully recycled to solid catalysts through a simple preparation method, and the solid catalyst was reused for the production of biodiesel with high conversion.

• Bulletin of the Korean Chemical Society
• /
• v.33 no.9
• /
• pp.2853-2854
• /
• 2012

• Journal of the Korea Safety Management & Science
• /
• v.2 no.4
• /
• pp.187-195
• /
• 2000

Electrochemical promotion of the reaction rate was investigated for CO oxidation in a solid electrolyte catalytic reactor where a thin film of Pt was deposited on the yttria stabilized zirconia as an electrode as well as a catalyst. It was shown under open circuit condition that potential was a mixed potential of $O_2$exchange reaction and electrochemical reaction induced by CO. The effect of electrochemical modification on the CO oxidation rate was studied at various overpotentials and $P_{CO}$$P_{O2}$.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.302-310
• /
• 2001

Cu/PET film composites were prepared by electroless copper plating method. In order to improve adhesion between electroless Cu plated layer and polyester (PET) film, the effect of pretreatment conditions such as etching method and mixed catalyst composition, and accelerator was investigated. Compared to NaOH etching medium, PET film was more finely etched by HCl solution, resulting in an improvement in adhesion between Cu layer and PET film. However, there were no significant differences in electromagnetic interference shielding effectiveness as a function of etching medium. The surface morphology of Cu plated PET film revealed that Pd/Sn colloidal particles became more evenly distributed in the smaller size by increasing the molar ratio of PdCl$_2$ : SnCl$_2$ from 1 : 4 to 1 : 16. With increasing the molar ratio of mixed catalyst, the adhesion and the shielding effectiveness of Cu plated PET film were increased. Furthermore, HCl was turned out to be a better accelerator than NaOH in order to enhance the activity of the mixed PdCl$_2$/SnCl$_2$ catalyst, which facilitated the formation of more uniform copper deposit on the PET film.