• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.4
• /
• pp.30-36
• /
• 2015

The principle of an illumination and projection system including LED light sources for a spot type stage lighting system was presented, and its optical system was designed with optimizing parameters by the analytical methods. A dichroic mirror incorporated with an illumination system to optimizing LED source positions and to obtain the compact system. The projection system was optimized with specific constraints such as a chromatic aberration, distortion aberration and angle of incidence angles. Optimized design system has a beam angle from $10^{\circ}$ to $45^{\circ}$, and its illuminance was 4,500lux at distance of 6m on the work plane.

• Journal of the Optical Society of Korea
• /
• v.7 no.2
• /
• pp.64-66
• /
• 2003

The optical gain and noise figure improved double-pass two-stage EDFA using a mirror, circulator, and gain-flattening filters is proposed. By double passing the pump light and removing the ASE propagating into the input part, the signal gain of 5 ㏈ and noise figure of 2.1 ㏈ are improved compared to the conventional single- and double-pass EDFA With gain-fattening filters in the second stage of EDFA, we obtain an improved flat gain with a gain flatness less than 1 ㏈ over 33-nm wavelength range at the 980-nm pump power of 86 ㎽.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.37 no.6
• /
• pp.85-96
• /
• 2000

It is necessary that fully differential operational amplifier circuit should drive an external load in the VLSI design such as SCF(Switched Capacitor Filter), D/A Converter, A/D Converter, Telecommunication Circuit and etc. The conventional CMOS operational amplifier circuit has many problems according to CMOS technique. Firstly, Capacity of large loads are not able to operate well. The problem can be solve to use class AB stages. But large loads are operate a difficult, because an element of existing CMOS has a quadratic functional relation with input and output voltage versus output current. Secondly, Whole circuit of dynamic range decrease, because a range of input and output voltages go down according as increasing of intergration rate drop supply voltage. The problem can be improved by employing fully differential operational amplifier using differential output stage with wide output swing. In this paper, we proposed new current mirror has large output impedance and good current matching with input an output current and compared with characteristics for operational amplifier using cascoded current mirror. To obtain large output swing and low power consumption we suggest a fully differential operational amplifier. The circuit employs an output stage composed new current mirror and two amplifier stage. The proposed circuit is layout and circuit of capability is inspected through simulation program(SPICE3f).

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.26 no.4
• /
• pp.278-283
• /
• 2013

This paper presents a design and fabrication of 0.5 V two stage operational amplifier. The proposed operational amplifier utilizes body-driven differential input stage and self-cascode current mirror structure. Cadence Virtuoso is used for layout and the layout data is verified by LVS through Mentor Calibre. The proposed two stage operational amplifier is fabricated using $0.13{\mu}m$ CMOS process and operation at 0.5 V is confirmed. Measured low frequency small signal gain of operational amplifier is 50 dB, power consumption is $29{\mu}W$ and chip area is $75{\mu}m{\times}90{\mu}m$.

• Journal of the Korean Society for Precision Engineering
• /
• v.27 no.3
• /
• pp.50-57
• /
• 2010

A high precision air bearing stage has been developed and calibrated. This linear-motor driven stage was designed to transport a glass or wafer with the X and Y following errors in nanometer regime. To achieve this level of precision, bar type mirrors were adopted for real time ${\Delta}X$ and ${\Delta}Y$ laser measurement and feedback control. With the laser wavelength variation and instability being kept minimized through strict environment control, the orthogonality of this type of control system becomes purely dependent upon the surface flatness, distortion, and assembly of the bar mirrors. Compensations for the bar mirror distortions and assembly have been performed using the self-calibration method. As a result, the orthogonality error of the stage was successfully decreased from $0.04^{\circ}$ to 2.48 arcsec.

• Proceedings of the Optical Society of Korea Conference
• /
• 2003.02a
• /
• pp.142-143
• /
• 2003

EDFA의 이득(gain)과 잡음지수(noise figure)는 매우 중요한 특성 중의 하나이다. 전송 시스템에서 필연적으로 발생하는 ASE 잡음을 제거하는 것이 중요하다. EDFA의 중간에 필터(filter)와 아이솔레이터(isolator)를 삽입하여 불필요한 ASE를 제거함으로써 이득과 잡음지수를 향상시킬 수 있으며, 기존의 단일경로(single-pass) EDFA에서 필터의 위치가 40-60％ 근처에서 이득과 잡음지수 향상이 가장 크게 된다. 그러나, 거울(mirror)을 사용하여 증폭 효율을 높인 이중경로(double-pass) EDFA에서 필터에 의한 이득 향상에 관한 연구발표는 아직까지 없다. (중략)

• Korean Journal of Optics and Photonics
• /
• v.22 no.1
• /
• pp.46-52
• /
• 2011

A confocal microscope was developed utilizing a scanning sample stage based on a home-built double-compound flexure guide. A scanning sample stage with nano-scale resolution consisted of a double leaf spring based flexure, a displacement amplifying lever, a Piezo-electric Transducer(PZT) actuator and capacitance sensors. The performance of the two-axis stage was analyzed using a commercial finite element method program prior to the implementation. A single line laser was employed as the light source along with the Photo Multiplier Tube(PMT) that served as the detector. The performance of the developed confocal microscope was evaluated with a mouse ear skin imaging test. The designed scanning stage enabled us to build the confocal microscope without the two optical scanning mirror modules that are essential in the conventional laser scanning confocal microscope. The elimination of the scanning mirror modules makes the optical design of the confocal microscope simpler and more compact than the conventional system.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.05a
• /
• pp.603-606
• /
• 2000

This dissertation is concerned with ultra-precision profile measurement of aspheric surfaces using contact probing technique. A contact probe has been designed as a sensing device to obtain measuring resolutions in nanometer regime utilizing a leaf spring mechanism and a capacitive-type sensor. The contact probe is attached on the z-axis during measurement while aspheric objects are supported on an precision xy-stage whose lateral motions are monitored by a set of two orthogonal plane mirror type laser interferometers. Experimental results show that the contact probing technique developed in this investigation is capable of providing a repeatability of 50 nanometers with a $\pm$3$\sigma$ uncertainty of 300 nanometers. Thermal disturbance is found the most significant factor that should be precisely controlled for accurate measurement.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.12 s.255
• /
• pp.1649-1657
• /
• 2006

Fizeau interferometer is well known optical instrument for measuring the lens profile accurately. The object of this study is focused on the design and optical measuring techniques for large optical components, such as a reflection mirror for astronomical purpose. Measuring of large optical lens, the object could not be moved as small one but the measuring instrument must be moved for the alignment, because of the geometric conditions and the accuracy of the stage. Therefore, a five axis stage is designed to align the Interferometer instead of the measuring object. This instrument will be used for an on machine measuring system in polishing machine for large optical lens.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.6
• /
• pp.169-174
• /
• 2019

Flexure joints are recently used in the ultra-precision mechanism for a telecommunication mirror stage. Flexure joints have several advantages coming from their monolithic characteristics. They can be used to reduce the size of manipulators or to increase the precision of motion. In our research, 6 dof(degree of freedom) mechanism is suggested for micrometer repeatability using a flexure mechanism. To design the 6-dof motion, the 2-dof planar mechanism are designed and assembled to make the 6-dof motion. To achieve a certain performance, it is necessary to define the performance of mechanism that quantifies the characteristics of flexure joints. This paper addresses the analysis and design of the 6-dof parallel manipulator with a flexure joint using a finite element analysis tool. To obtain experimental result, CCD laser displacement sensor is used for the total displacement and the stiffness for the 6-dof flexure mechanism.