• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 2005년도 연구개발 발표회 논문집
• /
• pp.185-190
• /
• 2005

This work presents a numerical procedure to optimize the elliptic-shaped pin fin arrays to enhance turbulent heat transfer. The response surface method is used as an optimization technique with Reynolds-averaged Navier Stokes analysis of flow and heat transfer. Shear stress transport (SST) turbulence model is used as a turbulence closure. Computational results for average heat transfer rate show a reasonable agreement with the experimental data. Four variables including major axis length, minor axis length, pitch and the pin fin length nondimensionalized by duct height are chosen as design variables. The objective function is defined as a linear combination of heat transfer and friction-loss related terms with weighting factor. D-optimal design is used to reduce the data points, and, with only 28 points, reliable response surface is obtained. Optimum shapes of the pin-fin arrays have been obtained in the range from 0.0 to 0.1 of weighting factor.

• 응용통계연구
• /
• 제16권1호
• /
• pp.129-140
• /
• 2003

본 논문은 통계적 영상처리를 이용하여 과일 선별 시스템을 개발하고자 한다. 히스토그램으로부터 과일 영상의 색깔에 대한 분포를 파악하고 이 표본 위치문제에서 Wilcoxon 검정을 이용하여 에지를 검출한다. 체인코드로부터 과일 영상의 면적, 둘레, 장ㆍ단축의 길이와 원형도 등 기하학적 특성값을 얻는다. 우리는 과일에 대한 영상실험을 통하여 통계적 에지검출 방법에 토대를 둔 시스템과 기존의 Sobel 연산자에 토대를 둔 시스템과의 비교 분석한다.

• 천문학회보
• /
• 제35권1호
• /
• pp.76.2-76.2
• /
• 2010

We report the extended far-ultraviolet (FUV) halo of NGC 891 above the galactic plane. The FUV intensity distribution is well described by two exponential components, one with the scale height of ~0.34 kpc and the other of ~2.3 kpc. The extraplanar FUV halo is traceable up to > 5 kpc. The FUV halo is attributable to scattered-off starlight by extraplanar dust. Using Monte-Carlo radiative transfer simulations, the FUV intensity distribution along the minor axis is found to be well modeled with two dust comonents. Its implications are discussed.

• Journal of Magnetics
• /
• 제2권3호
• /
• pp.101-104
• /
• 1997

Vector Moving Preisach model has been applied to the unoriented Co-based alloy thin film media. In the model, the out-of plane easy axis distribution of the particles was derived directly from the texture coefficient phkl obtained from XRD analysis, which corresponds to the fraction of the grains that have the {hkl} plane lying parallel to in-plane direction. The model was validated, by its prediction of a variety of responses, including major loop, minor loop, and the angular dependence of coercivities.

• 천문학회보
• /
• 제40권2호
• /
• pp.30.3-31
• /
• 2015

We present a kinematic analysis of 172 likely member galaxies of the Ursa Major Cluster. In order to understand the dynamical state of the cluster, we investigate the correlation of the cluster morphology with rotation, the velocity dispersion profile, and the rotation amplitude parallel to the global rotation direction. Both the minor axis and the rotation are very well-aligned with the global rotation axis in the outer region at half radius (> 0.5 $R_{max}$), but not in the inner region. The cluster exhibits low velocity dispersion and rotation amplitude profiles in the inner region, but higher in the outer. Both profiles exhibit outwardly increasing trends, suggesting an inside-out transfer of angular momentum of dark matter via violent relaxation, as revealed by a recent off-axis major-merging simulation. From Dressler-Schectman plots in the plane of galactic positions, and velocity versus position angle of galaxy, we are able to divide the Ursa Major Cluster into two substructures: Ursa Major South (UMS) and Ursa Major North (UMN). We derive a mass of $3.2{\times}10^{14}M_{\odot}$ for the cluster through the two-body analysis by the timing argument with the distance information (37 for UMN and 36 for UMS) and the spin parameter of ${\lambda}=0.049$. The two substructures appear to have passed each other 4.4 Gyr ago and are moving away to the maximum separation.

• 한국유체기계학회 논문집
• /
• 제5권1호
• /
• pp.7-12
• /
• 2002

As the first step to investigate the fundamental mechanism of a dispersed two-phase flow, we studied the detailed interactions between bubble or particle motion and flow around it. Experiments were carried out with a rising bubble or particle in stagnant water in a vertical pipe. Particles with different densities, and/or different shapes were used for comparison with a bubble. We adopted 3D-PTV (Three-Dimensional Particle Tracking Velocimetry) for measuring the bubble or particle motions, and PIV (Particle Image Velocimetry) for measuring the water flow simultaneously (Hybrid PIV). The experimental results showed that the oblate spheroidal solid particle rose along the longer axis direction at the point that the inclination of the longer axis reached the maximum, and the inclination direction changed after moving. The bubble moved to the direction that the spheroid's projected width grew up to the largest, and the minor axis of the oblate spheroidal body of the bubble was parallel to the moving direction. The trajectory of the center of the particle/bubble which was measured with 3D-PTV, was marked on the section (x-y) of the pipe. It exhibited the pattern of the particle/bubble motion.

• Journal of Biosystems Engineering
• /
• 제27권6호
• /
• pp.557-564
• /
• 2002

Corrugated board is an efficient low-cost structure material fur the boxes that are widely used for transporting, storing and distributing goods. Corrugated board is also considered as an orthotropic because the principal material directions are the same as in paperboard. The purpose of this study was to elucidate the principal design parameters of ventilating box through the FEA on the various types of ventilating hole. From the viewpoint of the stress distribution and stress level, the optimum pattern and location of the ventilating hole were vertically oblong, and symmetry position with a short distance to the right and left from the center of front and rear panel. And, the optimum location and pattern of hand hole were a short distance to the top from the center of both side panels, and modified shape to increase the radius of curvature of both side in horizontal oblong. In general, the optimum pattern and location of both the ventilating hole and hand hole based on the FEM analysis were well verified by experimental investigation. It is suggested that decrease in compressive strength of the box could be minimized in the same ventilating hole area under the condition of the length of major axis of ventilating hole is less than 1/4 of box length, the ratio of minor axis/major axis is 113.5∼l/2.5, and number of the ventilating holes is even and symmetrical.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.320-324
• /
• 2017

아음속 공기유동으로 수직분사하는 액체제트에 대하여 오리피스 형상이 달라질 경우, 분무특성에 어떠한 영향을 미치는지 실험적으로 연구하였다. 서로 다른 오리피스 길이 대 직경비와 타원형 노즐의 종횡비를 갖는 분사기들을 제작하여 수직분사 실험을 진행하였다. 원형노즐과 타원형 노즐에서의 분열길이를 비교하였으며, 타원형 노즐에서의 분열길이는 모든 실험조건에서 원형노즐에 비해 줄어들었다. 캐비테이션과 수력튀김 현상이 분사기 내부에 발달되는 분무차압 조건의 경우, 두 노즐 모두 분열길이가 감소하였다. 액주궤적의 경우, 장축으로부터 분무되는 액체제트가 횡방향 공기유동에 수직으로 부딪혀 나가는 경우가 액주의 궤적이 단축에 비해 더 휘어지며, 침투높이가 낮아진다.

• Journal of Mechanical Science and Technology
• /
• 제20권2호
• /
• pp.262-270
• /
• 2006

Direct numerical simulations (DNS) of turbulent channel flows up to $Re_{\tau}=1270$ are performed to investigate an elliptic feature and strain rate field on cross sections of coherent fine scale eddies (CFSEs) in wall turbulence. From DNS results, the CFSEs are educed and the strain rate field around the eddy is analyzed statistically. The principal strain rates (i.e. eigenvalues of the strain rate tensor) at the CFSE centers are scaled by the Kolmogorov length $\eta$ and velocity $U_k$. The most expected maximum (stretching) and minimum (compressing) eigenvalues at the CFSE centers are independent of the Reynolds number in each $y^+$ region (i. e. near-wall, logarithmic and wake regions). The elliptic feature of the CFSE is observed in the distribution of phase-averaged azimuthal velocity on a plane perpendicular to the rotating axis of the CFSE $(\omega_c)$. Except near the wall, phase-averaged maximum $(\gamma^{\ast}/\gamma_c^{\ast})$ and minimum $(\alpha^{\ast}/\alpha_c^{\ast})$ an eigenvalues show maxima on the major axis around the CFSE and minima on the minor axis near the CFSE center. This results in high energy dissipation rate around the CFSE.

• Bulletin of the Korean Chemical Society
• /
• 제28권12호
• /
• pp.2203-2208
• /
• 2007

Three possible binding modes of cationic meso-tetrakis(N-methylpyridinium-4-yl)porphyrin (TMPyP) to d[(GCATATATGC)2] duplex were investigated by the molecular dynamics (MD) simulation. Among the three binding modes namely, “along the groove”, “across the groove” and “face on the groove”, the “across the groove” model exhibited the largest negative binding free energy and the DNA backbone remained as the B form. In this model, the molecular plain of the TMPyP tilts 45o with respect to the DNA helix axis and is largely exposed to the solvent. TMPyP was stabilized mainly by the interaction between the positively charged neighboring pyridinium moieties of TMPyP and negatively charged phosphate groups of DNA. The result obtained in this work by MD and the report (Jin, B. et al., J. Am. Chem. Soc. 2005, 127, 2417.) that the spectral properties of poly[d(A-T)2] bound TMPyP in the presence and absence of the minor groove binding drug 4',6- diamidino-2-phenylindole are similar, we propose that TMPyP bind across the minor groove of the AT rich- DNA.