• 한국주조공학회지
• /
• 제27권3호
• /
• pp.131-134
• /
• 2007

[ $SF_6$ ] gas that is used as a protective cover gas for Mg and Mg alloys during melting and casting has extremely high greenhouse effect. CaO added Mg alloys could maintain their original mechanical properties and original abilities such as fluidity and hot tearing susceptibility. The ignition temperature increased with increasing CaO addition under ambient atmosphere and nitrogen atmosphere. The minimum amount of $SF_6$ gas decreased by 0.13 wt%CaO added AZ91D Mg alloy in the sealed condition.

• Journal of Electrical Engineering and Technology
• /
• 제8권1호
• /
• pp.110-117
• /
• 2013

Maximum Torque Per Amp (MTPA) control for induction motor drives seeks to achieve a desired torque with the minimum possible stator current. This is favorable in terms of inverter operation and nearly optimal in terms of motor efficiency. However, rotor resistance variation can cause significant performance degradation. This work demonstrates that existing MTPA controls perform sub-optimally as temperature varies. An adaptive MTPA control strategy is proposed that always achieves optimal performance without exhibiting hunting phenomenon regardless of rotor temperature. The proposed control is experimentally shown to accurately achieve the desired torque.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1990년도 하계학술대회 논문집
• /
• pp.363-366
• /
• 1990

In the indirect vector control method, the rotor resistance variation caused by operating temperature change is an undesirable nature. A new adaptation algorithm to compensate for the rotor resistance change based on the on-line estimation of field vector which requires the measurements of stator voltage and rotor speed is presented in this paper. Also minimum variance controller is presented for the adaptive control performance. This algorithm has been tested by simulating the induction machine using a digital computer and the results are discussed.

• 한국농공학회지
• /
• 제45권1호
• /
• pp.45-54
• /
• 2003

The effects of binder content and silica sand content on the durability characteristics of lightweight polymer concretes are examined. As a result, the flame lingering times using unsaturated polyester resin and non-combustible polyester resin were 60∼120 and 0∼4 seconds respectively, and the combustion lengths were 9∼11 mm and 0∼3 mm, respectively. Thus it is believed that the lightweight polymer concrete was incombustible and the light weight polymer concrete in which non-combustible material was added was perfectly non-combustible. The percent of original mass of lightweight polymer concrete, according to the freezing-thawing experiment, was below 0.3 %, which was much less than that of cement concrete. The pluse velocity, for the case of the binder content 28 %, showed the minimum decreasing rate for the lightweight polymer concrete with silica sand content of 50 %. The higher the binder content, the greater the durability. That is much higher than other material and believed that the freezing-thawing was suppressed by a low absorption.

• 약학회지
• /
• 제48권1호
• /
• pp.20-26
• /
• 2004

Twelve strains of Bifidobacterium spp. were isolated from the feces of healthy Korean 20∼30 years. The identification of genera from isolates were performed by the microscopic observation and fructose-6-phosphate phosphoketolase (F6PPK) activity which is the key enzyme to distinguish the Bifidobacterium spp. from other anaerobic bacteria. To determine the antibacterial resistance patterns, minimum inhibitory concentration (MIC) of several antibiotics (including anti-tuberculosis agents) was determined. Five of the isolate!, showed the high degree of resistance to vancomycin. To investigate the genetic diversity between isolates and type strain of Bifidobacterium spp. from KCTC, we peformed the RAPD-fingerprinting. Using a total set of four primers, it is possible to distinguish the isolates and Bifidobacterium spp. from KCTC. Thus, Bifidobacterium strains isolated from our samples may be a new species or strains of Bifidobacteriurn genera, and have the potential as a probiotics.

• 미생물학회지
• /
• 제39권4호
• /
• pp.293-295
• /
• 2003

Total 70 isolates of Escherichia coli obtained from pigs were studied. Forty four isolates had $\textregistered$-hemolytic activity which was heat labile. Minimum inhibitory concentration test indicated that 40 isolates (57.1%), 15 isolates (21.4%), 23 isolates (32.9%), and 5 isolates (7.1%) were resistant to ampicillin, cephalothin, gentamicin, and norfloxacin, respectively. None of them were extended spectrum $\textregistered$-lactamases (ESBLs) producer when the double disk synergy test (DDST) was performed.

• 한국정보디스플레이학회:학술대회논문집
• /
• 한국정보디스플레이학회 2000년도 제1회 학술대회 논문집
• /
• pp.89-90
• /
• 2000

A new technology realizing interconnection between Plastic Film LCDs panel and a driving circuit was developed under the processing condition of low temperature and pressure with ACFs developed for Plastic Film LCDs. The conduction failure of interconnection of the two resulted from elasticity, low thermal resistance and high thermal expansion of plastic substrates. Conductive particles with elasticity similar to the plastic substrate did not damaged a ITO electrode on plastic substrates, and low temperature and pressure process also did not deform the surface of plastic substrates. As a result highly reliable interconnection with minimum contact resistance was accomplished.

• 전자공학회논문지A
• /
• 제28A권9호
• /
• pp.743-751
• /
• 1991

This paper presents the 1.5\ulcorner PSA bipolar device which establishes the performance improvement such as the reduction of emitter resistance and substrate junction capacitance. To achieve the above electrical characteristics, RTA process and trench isolation technology were adapted. The emitter resistance and substrate capacitance of npn transistor having 1.5$[\times}6{\mu}m^{2}$emitter area was measured with 63$\Omega$and 28fF, respectively. The minimum propagation delay time shows 121ps at 0.7mW from the measurement of 31 stage ring oscillator.

• Journal of Welding and Joining
• /
• 제31권4호
• /
• pp.17-22
• /
• 2013

The excellent beam quality of high power fiber lasers are commonly used for remote welding applications in body job applications. The Welding speed and productivity is unmatched with any other welding technology including resistance spot welding or traditional laser welding. High tooling cost for clamping and bulky safety enclosures are obstacles which are limiting the use. With the newly developed Laser stitch welding gun we have an integrated clamping in the process tool and the laser welding is shielded in a way that no external enclosure is needed. Operation of this laser welding gun is comparable with resistance spot welding but 2-times faster. Laser stitch welding is faster than spot welding and slower than remote welding. It is a laser welding tool with all the laser benefits like welding of short flanges, weld ability of Ultra High Strength steel, 3 layers welding and Aluminium welding. Together with low energy consumption and minimum operation cost of IPG fiber laser it is a new and sharp tool for economic car body assembly.

• 한국세라믹학회지
• /
• 제35권6호
• /
• pp.610-618
• /
• 1998

Alumina were added to ceria based ceramic powders upto 9.7 vol% and composite powders were sprayed by plasma spraying process in order to improve the mechanical properties such as hardness fracture tough-ness and thermal shock resistance. The ceria based coating sprayed without alumina has the typical colum-nar and lamellar structure. Alumina addition has lowered the amount of columnar and lamellar sturcture Added alumina was segreagated in the grain boundary and grain of ceria based crystal accompanied with pore. The maximum value of density and the minimum value of porosity were observed at the sprayed coating with 4.8 vol% alumina. The hardness fracture toughness and thermal shock resistance were increased with alumina addition. The improvement of mechanical properties of plasma sparyed ceria based coatings result-ed from the disapperance of the columnar and lamellar sturcture by addition of alumina.