• EDISON SW 활용 경진대회 논문집
• /
• 제6회(2016년)
• /
• pp.101-105
• /
• 2016

Prandtl's Lifting-line theory is the classical theory of calculating aerodynamic properties. Though it is classical method, it predicts the aerodynamic properties well. By lifting-line theory, high aspect ratio is critical factor to decrease induced drag. And 'elliptic-similar' wing also makes the minimum induced drag. But due to the problem of manufacturing, tapered wing is preferred and have been utilized. In this Paper, by using Edison CFD, verifying the classical lifting-line theory. To consider induced drag only, using Euler equation as governing equation instead of full Navier-Stokes equation. Refer to the theory, optimum taper ratio which makes the minimum induced drag is 0.3. Utilizing the CFD results, plotting oswald factor over various taper ratio and investigating whether the consequences are valid or not. As a result, solving Euler equation by EDISON CFD cannot guarantee the theoretical values because it is hard to set the proper grid to solve. Results are divided into two cases. One is the values are decreased gradually and another seems to following tendency, but values are all negative number.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 1995년도 추계 학술대회논문집
• /
• pp.154-159
• /
• 1995

Numerical optimization technique with Navier-Stokes code has been used to reduce the drag of conventional ogival nose. Forebody optimizations are performed for supersonic laminar and turbulent flow conditions. To alleviate the computing time of aerodynamic drag calculation, axisymmetric boundary condition is implemented in the 3-dimensional Navier-Stokes code. The automated optimization procedure with gradient based method results in a drag reduction of $4\;\%$.

• 한국군사과학기술학회지
• /
• 제2권2호
• /
• pp.70-82
• /
• 1999

During the aircraft conceptual design stage, rapid aerodynamic analyses over various configurations are required. Hence, empirical and analytical methods play important roles in predicting the aero-dynamic characteristics. In this study, total drag estimation method based on empirical and analytical approaches is developed. By comparing with the results of the wind tunnel experiment and existing prediction methods, it is demonstrated that the developed method is accurate and useful in predicting total drag for the whole Mach number range.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권5호
• /
• pp.785-794
• /
• 2015

To obtain low resistance and high efficiency energy-saving ship, minimum total resistance hull form design method is studied based on potential flow theory of wave-making resistance and considering the effects of tail viscous separation. With the sum of wave resistance and viscous resistance as objective functions and the parameters of B-Spline function as design variables, mathematical models are built using Nonlinear Programming Method (NLP) ensuring the basic limit of displacement and considering rear viscous separation. We develop ship lines optimization procedures with intellectual property rights. Series60 is used as parent ship in optimization design to obtain improved ship (Series60-1) theoretically. Then drag tests for the improved ship (Series60-1) is made to get the actual minimum total resistance hull form.

• International Journal of Naval Architecture and Ocean Engineering
• /
• 제7권5호
• /
• pp.888-905
• /
• 2015

For Super-Cavitating Underwater Vehicles (SCUV), the numerical analyses and experiments in a large cavitation tunnel are carried out at relatively large Reynolds numbers. The numerical results agree well with experiments and the drag coefficient of SCUV is rarely changed by the Reynolds number. As the cavitation number is decreased, the cavity occurs and grows, the cavitator drag decreases and the body drag is affected by the degree of covering the body with the cavity. The tunnel effects, i.e. the blockage and the friction pressure drop of the tunnel, on the drag and the cavitation of SCUV are examined from the numerical results in between the tunnel and unbounded flows. In the tunnel, a minimum cavitation number exists and the drag of SCUV appears larger than that in unbounded flow. When the super-cavity covers the entire body, the friction drag almost disappears and the total drag of SCUV can be regarded as the pressure drag of cavitator.

• 한국전산유체공학회지
• /
• 제8권4호
• /
• pp.26-33
• /
• 2003

Smart UAV Development Program, one of the 21c Frontier R&D Program sponsored by MOST(Ministry of Science and Technology), was launched in 2002 As an air vehicle for the Smart UAV, CRW(Canard Rotor/wing) concept was one of the candidates compared in trade-off study. The CRW concept has not only been proven completely but its aerodynamic characteristics not known in detail yet. Two calculation methods were adopted in this study to obtain aerodynamic data for the CRW First method was the superpose DATCOM method which is capable of three lifting sufaces, and second one is the full Navier-Stokes computation around CRW configuration using overset grid method. Basic aerodynamic characteristics of the CRW configuration was analyzed and the minimum drag level with lift to drag ratio is presented. The peculiar flow characteristics around rotor/wing and hub were also examined and considered in the configuration design.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집E
• /
• pp.253-258
• /
• 2001

Control of drag force on a circular cylinder using a detached splitter plate is numerically studied for laminar flow. A splitter plate with the same length as the cylinder diameter(d) is placed horizontally in the wake region. Its position is described by the gap ratio(G/d), where G represents the gap between the cylinder base point and the leading edge of the plate. The drag varies with the gap ratio; it has the minimum value at a certain gap ratio for each Reynolds number. The drag sharply increases past the optimum gap ratio; this seems to be related to the sudden change in the bubble size in the wake region. This trend is consistent with the experimental observation currently available in case of turbulent flow. It is also found that the net drag coefficient significantly depends on the variation of base suction coefficient.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.956-961
• /
• 2003

Direct numerical simulations of flow over a circular cylinder are performed at two different Reynolds numbers (Re=220 and 300) that correspond to three-dimensional instabilities of mode A and mode B, respectively, to investigate the characteristics of drag and lift at these Reynolds numbers. The drag and lift coefficients are measured locally along the spanwise direction and their characteristics are studied in detail. The variation of total drag in time is large at Re=220, and the total drag becomes minimum when vortex dislocation occurs in the wake. The drag and lift variations in space are also closely associated with the evolution of vortex dislocation at this Reynolds number. At Re=300, vortex dislocation is not found in the wake and temporal variations of drag and lift are much smaller than those at Re=220, but their spatial variations are quite large due to the near-wake secondary vortices existing in the mode B instability.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2001년도 춘계학술대회 논문집
• /
• pp.129-134
• /
• 2001

The drag reduction of the cylinder having square dimpled surface was studied by the measuring the drag force acting on the cylinder. The level of the drag reduction was changed by the arrangement shape of the square grooves and Reynolds number. The drag of the cylinder was reduced about 28% with proper arrangement of square grooves. The flow field around the cylinder having grooves at the minimum drag was visualized by using post color ink in order to see the influence of the grooves. In this case, the separation points were sifted rearward and the wake region was smaller than that of the smooth cylinder.

• Journal of Advanced Marine Engineering and Technology
• /
• 제26권2호
• /
• pp.233-239
• /
• 2002

The drag reduction of the cylinder having square dimpled surface was studied by the measuring the drag force acting on the cylinder. The level of the drag reduction was changed by the arrangement shape of the square grooves and Reynolds number. The drag of the cylinder was reduced about 28% with proper arrangement of square grooves. The flow field around the cylinder having grooves at the minimum drag was visualized by using post color ink in order to see the influence of the grooves. In this case, the separation points were silted rearward and the wake region was smaller than that of the smooth cylinder.