• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.35D no.11
• /
• pp.23-30
• /
• 1998

The use of microstrip is very common for various passive microwave devices because of the rather simple and planar structure. However, many microstrip devices require fairly large surface areas, which results in real estate problems of finite substrates. In this paper, we proposed a perforated microstrip with longitudinal slow-wave effect and characterized experimentally and theoretically. The impedance matching to the reference impedance(50 $\Omega$) and the quality factor are greatly improved compared to the conventional slow-wave structure with modulated strip. Because of the structural simplicity, it can be easily applied to miniaturize many microstrip devices.

• International journal of advanced smart convergence
• /
• v.8 no.4
• /
• pp.154-160
• /
• 2019

In this paper, we propose the miniaturization size of wearable Range of Motion(ROM) and a system that can be connected with smart devices in real-time to measure the joint movement range dynamically. Currently, the ROM of the joint is directly measured by a person using a goniometer. Conventional methods are different depending on the measurement method and location of the measurement person, which makes it difficult to measure consistently and may cause errors. Also, it is impossible to measure the ROM of joints in real-life situations. Therefore, the wearable sensor is attached to the joint to be measured to develop a miniaturize size ROM device that can measure the range of motion of the joint in real-time. The sensor measured the resistance value changed according to the movement of the joint using a load cell. Also, the sensed analog values were converted to digital values using an Analog to Digital Converter(ADC). The converted amount can be transmitted wireless to the smart device through the wearable sensor node. As a result, the developed device can be measured more consistently than the measurement using the goniometer, communication with IoT-based smart devices, and wearable enables dynamic observation. The developed wearable sensor node will be able to monitor the dynamic state of rehabilitation patients in real-time and improve the rapid change of treatment method and customized treatment.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.51 no.1
• /
• pp.34-39
• /
• 2002

Most X-ray generator had been used do rectifier type transformer high tension generator which is supplied in a clinical diagnosis. But it is difficult to miniaturize and become light weight. Also, because the ripple rate of tube voltage is high, X-ray generating efficiency is very low. Therefore, it is supplied gradually from abroad being developed high tension generator for inverter type X-ray generator which use semi-conductor switching element for electric power that have high speed switching ability to solved these problem. But, semi-conductor element of big capacity are used by X-ray tube's big consumption power and diffusion is difficult in the small size hospital because production cost is ascending by doing digital control through DSP and product price becomes expensive. Therefore, in this paper, design and manufactured CR type voltage divider for feedback control of tube voltage of high frequency resonance type inverter and high tension transformer for high frequency to apply economical diffusion type X-ray generator which have wide output voltage and load extent. It is Proved do X-ray generator and stability of X-ray tube's output characteristics through an experiment.

• The Proceeding of the Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.3
• /
• pp.12-24
• /
• 2001

The key advantage of LTCC(low temperature co-fired ceramics) technology is the ability to integrate passive components such as resistors, capacitors, and inductors. More compact circuits with an increased scale of integration are needed with the development for advanced telecommunication system such as IMT-2000. LTCC technology can be obtained by removing these elements from the substrate surface to inside of ceramic body. And it can miniaturize the wireless phone through integration of planar patch antenna, duplexer, band pass filter, bias line, circuit of impedance matching and RF choke etc. Futhermore, with the multilayer chip process and its outstanding electrical material characteristics, LTCC is predestined for highly-integrated, cost effective wide band applications. This paper focuses on the general description of LTCC MCM technologies and the fabrication of the multilayer VCO module.

• Journal of Sensor Science and Technology
• /
• v.27 no.2
• /
• pp.99-104
• /
• 2018

A micro electromagnetic actuator with high vibration efficiency is proposed for use in an implantable hearing device. The actuator, which can be implanted in the middle ear, consists of membranes based on the stainless steel 304 (SUS-304), and other components. In conventional actuators, in which a thick membrane and a silicone elastomer are used, the size reduction was difficult. In order to miniaturize the size of the actuator, it is necessary to reduce the size of the actuation potion that generates the driving force, resulting in reduction of the electromagnetic force. In this paper, the electromagnetic actuator is further miniaturized by the metal membrane and the vibration amplitude is also optimized. The actuator designed according to the simulation results was fabricated by using micro-electro-mechanical systems (MEMS) technology. In particular, a $20{\mu}m$ thick metal membrane was fabricated using the erosion process, which reduced the length of the actuator by more than $400{\mu}m$. In the experiments, the vibration displacement characteristics of the optimized actuator were above 400 nm within the range of 0.1 to 1 kHz when a current of $1mA_{rms}$ was applied to the coil.

• Journal of the Korean Society of Visualization
• /
• v.8 no.2
• /
• pp.23-30
• /
• 2010

Regarding the aircrafts with a rotor blade system, the miniaturization of them is limited due to the rotor blade length and the tail rotor system. To miniaturize an aircraft, an equipment is required that increases thrust and also shortens the length of the rotor blade. The present study will conduct the flow analysis for miniaturizing the aircraft by applying a duct to the coaxial rotor blade system without tail rotor. First, the verification on the calculated results was conducted through the computational flow analysis on the coaxial rotor blade system without a duct. Then, the flow analysis for the coaxial rotor blade systems was performed including Ka-60 duct, Single duct, Twin duct, and Double duct, respectively. From the numerical results, the thrust coefficient appeared higher with the duct than without a duct for the coaxial rotor blade system. Especially, in the case of Double duct, the thrust was improved due to the increase of incoming flow and the extension of the wake area. These results will be used as the basic concepts for miniaturizing the aircraft with the rotor blade system. The flow analysis on the coaxial rotor blade system including the fuselage remains as a future work.

• Journal of the Korean Society for Precision Engineering
• /
• v.30 no.5
• /
• pp.520-528
• /
• 2013

A 20 mm diameter of small 5-D.O.F. force sensor has been developed for applications in MR-field Optical intensity modulation was adopted for transducing to miniaturize the sensor structure. For its accurate sensing of 5-D.O.F. force/moment, the elastic detecting module was designed to respond independently to each force or moment component. And for small size, two optical transducing modules of 2-D.O.F. and 3-D.O.F. were designed and integrated with the detecting module where optical fibers were arranged in parallel to make the sensor small. It is confirmed by calibration test that the detecting modules deforms linearly and independently to the input force. The results of evaluating test show that the range and resolution of forces are ${\pm}4$ N and 0.94~7.1 mN and the range and resolution of moments are ${\pm}120N{\cdot}mm$ and $0.023{\sim}0.034N{\cdot}mm$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.3
• /
• pp.170-176
• /
• 2017

In this paper, we proposed the miniaturized structure of the Log-Periodic Dipole Array(LPDA) antenna for PS-LTE(Pubic Safety-Long Term Evolution) service. The length of array dipole was shortened by adding a fractal tree element with iteration to the array dipole to miniaturize the LPDA antenna. As the result, the proposed LPDA antenna was reduced up to 25 %, compared a typical LPDA antenna. To validation of the proposed LPDA antenna specification, the proposed LPDA antenna is fabricated using aluminum with 1.5 mm thickness and performances are measured. Comparison between simulation result and experiment shows good agreement.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.9
• /
• pp.877-884
• /
• 2016

Nano communication system technologies are future core technologies that facilitate the implementation of tiny wireless communication systems with sizes in the range of hundreds of nanometers to tens of micrometers, which cannot be implemented by current wireless communication system technologies. In particular, novel nano communication system technology, which is based on electrical and mechanical resonance characteristics of carbon nanotube(: CNT), does not simply miniaturize system modules, but suggests a new approach that changes system architectures. Therefore, this paper surveys the state of the art on CNT-based nano communication technologies in aspects of system implementation, and proposes important research issues for convergence of nano and communication technologies.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.6
• /
• pp.2335-2343
• /
• 2018

This paper proposes an optimal damping control algorithm of the DTI (Direct Two-level Inverter) to miniaturize and reduce the weight of auxiliary power supply for railway vehicles. The conventional auxiliary power supply for railway vehicles uses a DC-DC converter to maintain the inverter input power from the line voltage smoothly. The proposed topology does not use a DC-DC converter for reducing of manufacturing and maintenance costs. It also proposes a DTI topology removed damping resistors that generate ground signal noise in a certain period. At this time, a resonance phenomenon of DC-link voltage occurs due to variation of the inductive load, and a method of controlling the resonance phenomenon of DC-link voltage is required. In order to suppress the resonance phenomenon of the DC-link voltage, at a point before resonance occurs, this paper introduces an algorithm to suppress the resonance phenomenon of DC-link voltage by compensating the resonance component of the q axis voltage of the synchronous reference frame. The proposed algorithm verifies the effect through simulation and experiment.