• 한국정밀공학회지
• /
• 제15권5호
• /
• pp.110-119
• /
• 1998

Dynamic cutting force variations in milling process were measured indirectly using spindle motor current. Magnitude of the spindle motor current is independent of cutting direction. Quasi-static sensitivity of the spindle motor current is higher than that of the feed motor current. Dynamic sensitivity of the spindle motor current is lower but cutting force was correctly represented by spindle RMS current in rough milling. In rough milling, chipping and tool fracture were well detected by the proposed tool fracture index using spindle motor current.

• International Journal of Precision Engineering and Manufacturing
• /
• 제7권3호
• /
• pp.8-13
• /
• 2006

Plunge milling process is used for machining hole and is widely used in aerospace, automobile, and die/mold industries. The cutter is fed in the direction of spindle axis which has the highest structural rigidity. The kinematics of plunge milling differs from the traditional turning and milling in aspect of tool engagement and chip generation. This paper proposes the mechanistic cutting force model for plunge milling. Uncut chip thickness is calculated using the present cutter edge position and the previous cutter edge position. Instantaneous cutting force coefficients, which depend only on instantaneous uncut chip thickness, are derived based on the mechanistic approach. The developed cutting force model is verified through comparison of the predicted and the measured cutting forces.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.504-509
• /
• 2004

Chemical machining(CHM) is a special process which material removed by contact of strong etchant. The application as industrial process was started from aircraft industry after 2nd world war. Chemical milling, one of the CHM process, initially became commercial bussiness and it was called chem-mill. Even today, this process widely used to remove the material from aircraft wings and fuselage panel in aircraft industry. In this study, it is attempted to design the cylinder pattern which minimize the weight within the allowable stress using chemical milling.

• 한국정밀공학회지
• /
• 제26권2호
• /
• pp.26-34
• /
• 2009

This paper is related to MQL (Minimum Quantity Lubrication) milling process, which is one of the environmentally friendly cuttings. The objective is to compare MQL milling process with conventional cutting fluid systems. To this end, machinability of MQL milling process was investigated, followed by the cost evaluation. Cutting force, surface roughness, tool wear, and cutting temperature were compared with each cutting fluid method. Consequently, total production costs wear evaluated with the mathematical models in terms of machining cost and cutting fluid loss.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.1059-1062
• /
• 1995

In cutting system, relative displacement between rool and workpiece is very important. Even though there have been so many works for modeling cutting process of end-milling, most of them have considered only one displacement of either tool or workpiece instead of both. In this paper, the relative displacement between tool and workpiece is considered for modeling cutting process of end-milling using simple experimental modal analysis and cutting force simulation program is developed. In cutting force model, instantaneous uncut chip thickness model is used and Runge-Kutta method is used for the simulation of time varying cutting system.

• 한국정밀공학회지
• /
• 제34권4호
• /
• pp.253-258
• /
• 2017

This paper presents a numerical study on the thermal characteristics of a milling process of titanium alloy with nanofluid minimum-quantity lubrication (MQL). The computational fluid dynamics (CFD) approach is introduced for establishing the numerical model for the nanofluid MQL milling process, and estimated temperatures for pure MQL and for nanofluid MQL using both hexagonal boron nitride (hBN) and nanodiamond particles are compared with the temperatures measured by thermocouples in the titanium alloy workpiece. The estimated workpiece temperatures are similar to experimental ones, and the model is validated.

• 한국정밀공학회지
• /
• 제17권8호
• /
• pp.46-52
• /
• 2000

3D Welding and Milling is a solid freeform fabrication process which is based on the combination of welding as additive and conventional milling as subtractive technique. This hybrid approach enables direct building of metallic parts with high accuracy and surface finish. Although it needs further improvements it shows an application potential in rapid tooling of injection mold inserts as the investigation results show. To optimize the process for higher surface quality and accuracy effectively Taguchi method is applied to the experimental investigation. in this way relationships between process parameters and final product qualities such as tensile strength and surface hardness are found with minimal efforts.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.1-7
• /
• 2011

The mode analysis of end-milling was introduced using recursive parametric modeling. Also, a numerical mode analysis of FRF in end-milling at different conditions was performed systematically. In this regard, a REIVM(recursive extended instrumental variable method) modeling algorithm was adopted and natural modes of real and imaginary part were discussed. This recursive approach can be used for the on-line system identification and monitoring of an end-milling for this purpose. For acquiring a cutting force, an experimental practice was performed. And these end-milling forces were used for the calculation of FRF(Frequency response function) and its mode analysis. Also, the FRF was analysed for the prediction of end-milling system. As a results, this algorithm was successful in each condition for the detection of natural modes of end-milling. After numerical analysis of the FRF, the tooth passing frequency was discriminated in their FRF, power spectrum and mode calculation.

• 한국분말재료학회지
• /
• 제23권1호
• /
• pp.54-60
• /
• 2016

This study focuses on fabricating silver flake powder by a mechanical milling process and investigating the formation of flake-shaped particles during milling. The silver flake powder is fabricated by varying the mechanical milling parameters such as the amount of powder, ball size, impeller rotation speed, and milling time of the attrition ballmill. The particle size of the silver flake powder decreases with increasing amount of powder; however, it increases with increasing impeller rotation speed. The change in the particle size of the silver flake powder is analyzed based on elastic collision between the balls, taking energy loss of the balls due to the powder into consideration. The change in the particle size of the silver flake powder with mechanical milling parameters is consistent with the change in the diameter of the elastic deformation contact area of the ball, due to the collision between the balls, with milling parameters. The flake-shaped silver particles are formed at the elastic deformation contact area of the ball due to the collision.

• Advances in materials Research
• /
• 제6권3호
• /
• pp.245-255
• /
• 2017

High energy ball milling is employed to produce iron matrix- multiwall carbon nanotube (MWCNT) reinforced composite. The damage caused to MWCNT due to harsh ball milling condition and its influence on interfacial bonding is studied. Different amount of MWCNT is used to find the optimal percentage of MWCNT for avoidance of the formation of chemical reaction product at the matrix - reinforcement interface. Effect of process control agent is assessed by the use of different materials for the purpose. It is observed that ethanol as a process control agent (PCA) causes degradation of MWCNT reinforcements after milling for two hours whereas solid stearic acid used as process control agent, allows satisfactory conservation of MWCNT structure. It is further noted that at a high MWCNT content (~ 2wt.%), high energy ball milling leads to reaction of iron and carbon and forms iron carbide (cementite) at the iron-MWCNT interface. At low percentage of MWCNT, dissolution of carbon in iron takes place and the amount of reinforcement in iron matrix composite becomes negligibly small. However, under the present ball milling condition (ball to metal ratio~ 6:1 and 200 rpm vial speed) iron-1wt.% MWCNT composite of good interfacial bonding can retain the tubular structure of reinforcing MWCNT.