• ETRI Journal
• /
• v.28 no.5
• /
• pp.656-659
• /
• 2006

This letter presents a new polarizer which has a simple comb structure inside a circular waveguide. The electrical performance of the proposed comb polarizer is optimized by a circular waveguide radius and by the physical parameters of the comb plates. This polarizer is suitable for providing good performance in millimeter-band application because of its simple structure and low fabrication cost. In our experiments the dual-band comb polarizer designed in band 1(K) and band 2(Ka) showed good electrical performance without any tuning elements.

• Proceedings of the IEEK Conference
• /
• 2008.06a
• /
• pp.411-412
• /
• 2008

The high performance 94 GHz MMIC(Monolithic Micro-wave Integrated Circuit) single balanced mixer was designed and fabricated, using MHEMT structure based diodes and a CPW(Coplanar Waveguide) tandem coupler. A novel single-balanced structure of diode mixer is proposed in this work, where a 3-dB tandem coupler with two section of parallel-coupled line. Implemented air-bridge crossover structures achieve wide frequency operation and the fabricated mixer exhibits excellent LO-RF isolation, larger than 30 dB, in the 5 GHz bandwidth of 91-96 GHz. A good conversion loss of 7.4 dB is measured at 94 GHz. The proposed MHEMT-based diode mixer shows superior LO-RF isolation and conversion loss to those of the W-band mixers reported to date.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.925-928
• /
• 2005

In this study, we fabricated the DAMLs using surface micromachining technology as well a low loss coupler for the millimeter-wave band applications using these DAMLs. The structure of DAML is that a signal line is supported on ground plane by dielectric posts. Therefore it has advantages about the loss characteristic and the stable structure. The other advantage of the DAML process is a simple and convenient technique using 4 mask steps, even if it has a micromachining technology. The lowest loss of the fabricated DAML was obtained 2.2 dB/cm at 110 GHz. To obtain the low loss characteristic, couplers were designed and fabricated by using DAMLs. The fabricated ring hybrid coupler has the coupling of 3.58 dB and the thru of 3.31 dB at 60 GHz. We can also obtain the coupling of 3.42 dB, the thru of 3.82 dB from fabricated branch line coupler at 60 GHz.

• Proceedings of the IEEK Conference
• /
• 2006.06a
• /
• pp.467-468
• /
• 2006

To perform the comparative study, we experimented on two differential epitaxial structures, the conventional Metamorphic High Electron Mobility Transistor (MHEMT) using the InAlAs/InGaAs structure and the InP-composite channel MHEMT adopting the InAlAs/InGaAs/InP/n-InP structure. Compared to the conventional MHEMT, the InP-composite channel MHEMT shows improved breakdown performance; over about 3.5 V. This increased breakdown voltage can be explained by the lower impact ionization coefficient of the InP-composite channel MHEMT than that of the conventional MHEMT.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.42 no.3 s.333
• /
• pp.33-38
• /
• 2005

In this paper, we have designed and fabricated a hybrid ring coupler to prove the fabrication possibility of various passive components, applying millimeter wave using newly proposed transmission lines, i.e. BAMLs. The characteristics of the fabricated hybrid ing coupler were a the S31(coupling) of 3.58 dB, the S21(thru) of 3.31 dB at the 60 GHz center frequency, the S11(return loss) over 16.17 dB, S41(isolation) over 55 dB at 61 GHz, and the phase difference between port 2 and port 3 of $180{\pm}loat$ 60GHz. In order to reduce the size of hybrid ring coupler, we designed the hybrid ring coupler which inserts a slow wave structure. With this structure, we were able to reduce the hybrid ring coupler by $33\%$ area.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.6
• /
• pp.47-53
• /
• 2023

In this paper, We designed a waveguide-type feed structure that converts millimeter wave dual-polarized signals into monopulse signals and presented a manufacturing method. At millimeter-wave such as the W band, the size of the waveguide is very small, making it very difficult to manufacture complex structures. Therefore, because manufacturability is important for the waveguide-type feed structure in the millimeter-wave, electro forming and diffusion bonding were proposed and verified in this study. The designed monopulse feed structure consists of eight 180° hybrids that combine 90° hybrids and self-compensating phase shifters, and four OMTs to separate dual polarization. The designed feed structure was designed to facilitate electro forming and diffusion bonding, and the manufactured feed structure was verified through a network analyzer. It was confirmed that the two proposed production methods produce a monopulse signal well through the measured magnitude and phase of the port.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.599-602
• /
• 2005

In this paper, we have performed a study that modifies the CPW Pad configurations to improve an $f_{max}$ characteristic of metamorphic HEMT. To analyze the CPW Pad structures of MHEMT, we use the ADS momentum simulator developed by $Agilent^{TM}$. Comparing the employed structure (G/W = 40/100 m), the optimized structure (G/W = 20/25 m) of CPW MHEMT shows the increased $S_{21}$ by 2.5 dB, which is one of the dominant parameters influencing the $f_{max}$ of MHEMT. To compare the performances of optimized MHEMT with the employed MHEMT, DC and RF characteristics of the fabricated MHEMT were measured. In the case of optimized CPW MHEMT, the measured saturated drain current density and transconductance $(g_m)$ were 693 mA/mm and 647 mS/mm, respectively. RF measurements were performed in a frequency range of $0.1{\sim}110$ GHz. A high $S_{21}$ gain of 5.5 dB is shown at a millimeter-wave frequency of 110 GHz. Two kinds of RF gains, $h_{21}$ and maximum available gain (MAG), versus the frequency, and a cut-off frequency ($f_t$) of ${\sim}154$ GHz and a maximum frequency of oscillation ($f_{max}$) of ${\sim}358$ GHz are obtained, respectively, from the extrapolation of the RF gains for a device biased at a peak transconductance. An optimized CPW MHEMT structure is one of the first reports among fabricated 0.1 m gate length MHEMTs.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.4
• /
• pp.47-52
• /
• 2012

We have designed the waveguide to microstrip transition using a probe structure for the center frequency of 200 GHz transceiver. The waveguide to microstrip transition is composed of probe, taper and microstrip transmission line. For design of the transition, we simulated the lengths and width of the probe and the taper to optimize the center frequency and the bandwidth using HFSS simulation tool from Ansoft. The transition is designed back-to-back structure. From the simulation results, the transition exhibits that insertion loss is below - 0.81 dB and the return loss less than -10 dB in range of 186 ~ 210 GHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.6 s.348
• /
• pp.46-52
• /
• 2006

We report on a high performance 94 GHz MMIC resistive mixer using 70-nm metamorphic high electron mobility transistor (MHEMT) and micro-machined W-band ring coupler. A novel 3-dimensional structure of resistive mixer was proposed in this work, and the ring coupler with the surface micro-machined dielectric-supported air-gap microstrip line (DAMLs) structure was used for high LO-RF isolation. The fabricated mixer showed an excellent LO-RF isolation of -29.3 dB and a low conversion loss of 8.9 dB at 94 GHz. To our knowledge, compared to previously reported W-band mixers, the proposed MHEMT-based resistive mixer using micro-machined ring coupler has shown superior LO-RF isolation as well as similar conversion loss.

• Proceedings of the IEEK Conference
• /
• 2004.06b
• /
• pp.335-338
• /
• 2004

We suggest Q-band MEMS MIMIC (Millimeter wave Monolithic Integrated Circuit) HEMT Oscillator using DAML (Dielectric-supported Airgapped Mcrostrip Line) structure. We elevated the signal lines from the substrate using dielectric post, in order to reduce the substrate dielectric loss and obtain low losses at millimeter-wave frequency. These DAML are composed with heist of $10\;{\mu}m$ and post size with $20\;{\mu}m\;{\times}\;20\;{\mu}m$. The MEMS oscillator was successfully integrated by the process of $0.1\;{\mu}m$ GaAs PHEMTs, CPW transmission line and DAML. The phase noise characteristic of the MEMS oscillator was improved more than 7.5 dBc/Hz at a 1 MHz offset frequency than that of the CPW oscillator And the high output power of 7.5 dBm was measured at 34.4 GHz.