• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.25 no.3
• /
• pp.111-116
• /
• 2019

Thermal insulation performance of new insulation packaging made of recycled PET nonwoven (thickness : 10 mm) was verified by conducting comparative experiment with an EPS box (thickness : 25 mm) and a double wall corrugated box (thickness : 7 mm). Three ice packs (300 g) were positioned 200 mm above the bottom inside each box, all of which are placed side by side and temperature change of 2 points (5mm under middle icepack and 130 mm under middle icepack) was recorded by data logger (GL-840, Graphtec) for 16 hours under the environment of 29℃. The new packaging box showed 75% higher insulation performance than the EPS box and 180% higher than the corrugated box. In order to figure out the reason for insulation performance difference among boxes, thermal conductivities of each box material were measured using heat flow meter (HFM436 lamda, Netzsch). U-value (thermal conductivity divided by thickness) of EPS was lower than recycled pet nonwoven by 57%, which seemed to be opposite to the result of insulation test of boxes. This was explained by high water vapor transmission rate of EPS (6 times higher than PET insulation) and air pocket effect of PET insulation.

• Journal of Conservation Science
• /
• v.32 no.1
• /
• pp.75-88
• /
• 2016

In this study, 5 mural paintings in the Buddhist temples of Joseon era were researched for component analysis on the soil contained in the walls. The results of particle size analysis showed that the ratio of particle contents were different in each layer. In the finishing layer, the distribution of the middle sand fraction is higher than that of the middle layer. The results of XRD analysis showed that quartz, feldspar, and clay mineral are the main components of sand, suggesting similar mineral composition to that of ordinary soil component. It seems weathered rocks were used for construction of the walls. The main chemical components detected from EDX analysis were Si, Al, Fe, and K. Also the SEM images showed sand or clay sized minerals. In conclusion, the walls of the buddhist mural paintings in Joseon Dynasty had been constructed by using the loess, and had been produced by using mixture of clay and sand particles of different sizes for each layer. This study identified the characteristics of the materials and the manufacturing technologies used on the walls of mural paintings of Buddhist temples in Joseon era.

• Imaging Science in Dentistry
• /
• v.47 no.3
• /
• pp.181-187
• /
• 2017

Purpose: The purpose of this study was to measure the buccal bone thickness and angulation of the maxillary incisors and to analyze the correlation between these parameters and the root position in the alveolar bone using cone-beam computed tomography (CBCT). Materials and Methods: CBCT images of 398 maxillary central and lateral incisors from 199 patients were retrospectively reviewed. The root position in the alveolar bone was classified as buccal, middle, or palatal, and the buccal type was further classified into subtypes I, II, and III. In addition, the buccolingual inclination of the tooth and buccal bone thickness were evaluated. Results: A majority of the maxillary incisors were positioned more buccally within the alveolar bone, and only 2 lateral incisors(0.5%) were positioned more palatally. The angulation of buccal subtype III was the greatest and that of the middle type was the lowest. Most of the maxillary incisors exhibited a thin facial bone wall, and the lateral incisors had a significantly thinner buccal bone than the central incisors. The buccal bone of buccal subtypes II and III was significantly thinner than that of buccal subtype I. Conclusion: A majority of the maxillary incisor roots were positioned close to the buccal cortical plate and had a thin buccal bone wall. Significant relationships were observed between the root position in the alveolar bone, the angulation of the tooth in the alveolar bone, and buccal bone thickness. CBCT analyses of the buccal bone and sagittal root position are recommended for the selection of the appropriate treatment approach.

• Journal of the Korean Geographical Society
• /
• v.34 no.3
• /
• pp.231-246
• /
• 1999

The geomorphic deformation of the alluvial fans by tectonic movement was investigated along the lineaments of the northern part of the Bulguksa fault system. Based on the aerial photographs interpretation and field surveys Bulguksa fault system was identified as an active reverse fault which has displaced the Quaternary fan deposits. Bulguksa fault system strikes for the direction of NW-SE and N-S. These two lineaments of active fault are crossing at Jinty village in Kyungju city and the fault plane forms here almost vertical dip. Thelateral pressures from the two directions have possibly influenced on the formation of the vertical dip at Jinty village. It should be resulted from that the two pressures responsible for the active reverse fault at which the one with the NW-SE strike thrusts the hanging wall of Tohamsan block southwestward and the other pressure with the N-S jstrike thrusts it westwrd over the foot wall of the fan deposits. The marine oxygen isotope stage 8(0.30-0.25 Ma. BP) and stage 6(0.20-0.14 Ma. BP) are presumed to be the ages of high and middle surfaces of the alluvial fan, repectively. The vertical dispiacements on the high surface along the Bulguksa fault system are about 10.5m at Ha-dong, 9.5-10.5m at Jinhyun-dong, and about 10m at Jinty village. And the vertical displacement on the middle surface was measured about 6m high at Ha-dong. The average slip rate of vertical displacements is calculated about 0.03-0.043mm/y.

• Journal of Korean Society of Forest Science
• /
• v.45 no.1
• /
• pp.62-67
• /
• 1979

Ultraviolet microscopy of ultrathin sections of wood has proved to be one of the useful means for determining the lignin distribution in the various regions of the cell wall. Also, spectral approach and quantitative analysis of isolated compound middle lamella fraction from birch xylem have revealed that the lignin associated with the vessel secondary wall and middle lamella is composed predominantly of gualacylpropane units. Lignin deposited in the fiber and ray parenchyma secondary walls is composed mostly of syringylpropane units. The middle lamella lignin around fibers and ray cells contains both guaiacyl and syringyl propane quits. On the basis of the results above, this research was carried out to clarify the origin of milled wood lignin (MWL) by analysing the chemical characteristics of ML MWLs extracted at various milling stages. The amount of phenolic hydroxyl-, ${\alpha}$-carbonyl-, and methoxyl-group in the MWL's increases the milling time. And progressive mining contributes to the merease of ratio of syringylaldehyde to vanillin(S/V ratio) after nitrobenzene oxidation of MWL. Accordingly, It could be concluded that milled wood lignin extracted at the initial milling stage derives from compound middle lamella region of cell wall, whereas, with progressive milling, lignin of secondary wall of fiber is introduced gradually to milled wood lignin. These results are suggesting that heterogeneous chemical structure of lignins in hardwood exists. Although milled wood lignin at the initial stage seems to have lower molecular weight in comparison with milled wood lignin extracted at final milling stage from the result of Gel-filtration curves, further study would be required on molecular weight distribution of milled wood lignin in future.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.14 no.6
• /
• pp.1-9
• /
• 2010

Most of shear wall structures require openings in shear walls and thus shear walls are linked by floor slabs or coupling beams resulting in the coupled shear wall structures. When these structures are subjected to seismic excitations, excessive shear forces are induced in coupling beams. Accordingly, brittle failure of coupling beams may occur or shear walls may yield first. To avoid this problem, damping devices can be installed in coupling beams. It can increase the vibration control effect and improve the seismic resistance performance of the coupled shear wall structure by avoiding stress concentration and the brittle failure of coupling beams. Based on this background research, an LRB (lead rubber bearing) was introduced in the middle of the coupling beam in this study and the authors investigated the seismic response control effect and stress distribution of the proposed system. To this end, a modeling technique that can effectively predict the structural behavior of coupled shear wall structures has been proposed. With this proposed technique, time history analyses of the example coupled shear wall structure subjected to seismic excitation were performed and the vibration control effects of the seismic responses were investigated.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.19 no.5
• /
• pp.211-217
• /
• 2019

The three major inventions of Jeju include the field wall of Kim Koo Pan Gwan in 1234, Jeongnang in the custom of grazing the people of Jeju, and Olleh in the tomb of Munbang-gui in 1406. Field wall, Oedam from the stone and the stone of numerical play, made Koendang, a friendship society. Even with a typhoon that is more than 30m/s, the Koendang which is about 1.5m high, will not collapse. Similarly, the main family networks of Jeju society do not collapse under any difficulties situation. When building a field wall, two stones, which are under the ground, are placed side by side, and the upper left stone is placed on top and the upper right stone is attached regularly. One stone or two stone is attached from the bottom to the top, and when a stone is small or large, a flat field is formed in one space. The Family networks is close to the grandfather, grandmother, father, mother, and me, and the distant kin represents a horizontal relationship. The field wall is a vertical relationship that builds up from bottom to top of the vertical relation, while the Koendang is a horizontal relationship where blood is distributed to the grandson of his upper grandparents. This paper proves by a non-orthogonal symmetric weighted Hadamard matrix of whether the stone in the middle of a field wall has large stones (small).

• Journal of Korean Neurosurgical Society
• /
• v.61 no.3
• /
• pp.407-414
• /
• 2018

Objective : The purpose of the present study was to describe an OrBitoZygomatic (OBZ) surgical variant that implies the drilling of the orbital roof and lateral wall of the orbit without orbitotomy. Methods : Design : cross-sectional study. Between January 2010 and December 2014, 18 patients with middle fossa lesions underwent the previously mentioned OBZ surgical variant. Gender, age, histopathological diagnosis, complications, and percentage of resection were registered. The detailed surgical technique is described. Results : Of the 18 cases listed in the study, nine were males and nine females. Seventeen cases (94.5%) were diagnosed as primary tumoral lesions, one case (5.5%) presented with metastasis of a carcinoma, and an additional one had a fibrous dysplasia. Age ranged between 27 and 73 years. Early complications were developed in four cases, but all of these were completely resolved. None developed enophthalmos. Conclusion : The present study illustrates a novel surgical OBZ approach that allows for the performance of a simpler and faster procedure with fewer complications, and without increasing surgical time or cerebral manipulation, for reaching lesions of the middle fossa. Thorough knowledge of the anatomy and surgical technique is essential for successful completion of the procedure.

• Journal of the Korean Wood Science and Technology
• /
• v.44 no.2
• /
• pp.157-165
• /
• 2016

This study investigated several anatomical characteristics of Paulownia tomentosa roots. The root wood was separated into three parts from stem base (top, middle, and base) at different positions below ground. Qualitative anatomical data suggested that the growth rings in earlywood and latewood were structurally different. Furthermore, the root wood vessels were found having 2 to 3 radial multiples and they were appeared in the form of clusters. In addition, some sheath cells and septate axial parenchyma were observed. Regarding the quantitative anatomical characteristics, vessel and ray numbers per $mm^2$, as well as ray width and height differed significantly among the top, middle, and base rood wood parts. However, there were no significant differences in vessel diameters, cell wall thickness, and width and length of wood fibers among those parts. The crystallinity of the root top part was slightly higher than that of the middle and base parts. Furthermore, the vessel numbers, ray numbers, and ray width and height in the near pith (NP) area were higher compared to those in the near bark (NB) area. However, the fiber width and fiber length at NP were lower than those at NB. Overall, this study demonstrated some significant differences in the anatomical characteristics of the top, middle, and base parts of root wood from Paulownia tomentosa.

• Journal of Korean Society of Steel Construction
• /
• v.20 no.6
• /
• pp.793-805
• /
• 2008

Recently, steel modular systems are developed and have been applied to the projects requiring fast construction such as military barracks and vertical expansion of school buildings. The existing modular system with standard module of ${6m\times3m}$ has a problem that many columns are duplicated in the module connection and the wall thickness increases. In this study, $12m{\times}3m$ module is proposed to solve this problem. Various types of beam-middle column connection which are essential for realizing the $12m{\times}3m$ module are proposed and their maximum load capacity and failure mode are analytically and experimentally evaluated. The comparison between analytical and experimental results shows that the maximum axial load and failure mode can be accurately estimated by finite element analysis. Some connection types which have higher failure load than the design load of the column, can be used as the beam-middle column connection detail of the $12m{\times}3m$ module.