• Journal of the Korean Ceramic Society
• /
• v.35 no.5
• /
• pp.465-471
• /
• 1998

Lead titanate(PT) and lead magnesium niobate(PMN) ceramic powders were prepared by microwave hy-drothermal method using teflon bomb. Raw materials were Pb(NO3)2 and TiO2 for lead titanate and Pb(NO3)2 Nb2O5 and Mg(NO)3.6H2O for PMN with NaOH as mineralizer in both cases. in lead titanate synthsis rate of microwave hydrothermal method was faster three times than one f conventional hydrothermal methods In lead magnesium niobate synthsis the mixture of perovskite and pyrochlore phases was obtained by single step technique and the PMN was not obtained by double step technique due to low temperature limitation of teflon bomb.

• Journal of the Korean Ceramic Society
• /
• v.43 no.2 s.285
• /
• pp.126-130
• /
• 2006

Nano-sized hydroxyapatite (HAp) powders were synthesized by a microwave-hydrothermal method using $H_3PO_4\;and\;Ca(OH)_2$ as starting materials. The applied microwave powers and mole ratio of Ca/P were served as powerful factors in the synthesis of calcium phosphate. In the case of relatively low microwave power of 450 Wand Ca/P ratio of 1.57, the mixed calcium phosphate compounds were detected in the synthesized powders. But in the case of running at 550 Wand 1.67(Ca/P), the synthesized powder showed the monophase of HAp having two kinds of morphologies. One was a needle shape with $5\~15\;nm$ in width and $20\~50\;nm$ in length, and the other was a spherical shape of $10\~40\;nm$ in diameter.

• Korean Chemical Engineering Research
• /
• v.53 no.5
• /
• pp.570-575
• /
• 2015

The green algae have cellulose as a main structural component of their cell wall and the cellulose content in green algae is much higher than other marine algae such as brown algae and red algae. Furthermore, green algae do not contain lignin in their cell wall and store starch as food in their plastids. Thus, it was investigated that the effect of hydrothermal pretreatment process utilizing microwave irradiation for Ulva pertusa Kjellman, a division of green algae, which is expected to be utilized for bioenergy production, on the enzymatic hydrolysis. The hydrothermal temperature have an effect on the pretreatment of Ulva pertusa Kjellman, but the effect of power of microwave irradiation is negligible. The rate of enzymatic hydrolysis was increased as the hydrothermal temperature increased until $140^{\circ}C$. The enzymatic hydrolysis of pretreated Ulva pertusa Kjellman under the optimum pretreatment conditions (50 W of microwave irradiation power and $150^{\circ}C$ of hydrothermal temperature) with cellulase, ${\alpha}$-amylase, and Novozyme 188 having ${\beta}$-glucosidase acitivity resulted in the saccharification of 96 wt% of total carbohydrate in Ulva pertusa Kjellman during 3 hrs, while it took 24 hrs for the enzymatic hydrolysis of untreated Ulva pertusa Kjellman. It confirmed that the hydrothermal pretreatment was effective on Ulva pertusa Kjellman for the enzymatic hydrolysis.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2014.11a
• /
• pp.260-261
• /
• 2014

$TiO_2$ nanotubes (TNT) synthesized by microwave-assisted hydrothermal method by using $TiO_2-P25$ as a precursor at hydrothermal temperature $150^{\circ}C$ in 4 hours. The concentration of alkaline solution is between 4M and 10M. Samples were characterized by X-ray diffraction (XRD), Raman spectroscopy (RS), Transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET) and UV-vis DRS spectroscopy. The results demonstrated the effects of the alkali concentration to the formation of nanotubes. The photocatalytic activity was investigated by degradation of Methylene Blue (MB).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2007.06a
• /
• pp.300-301
• /
• 2007

$Mg_4(Nb_{2-x}V_x)O_9$ (MNV) ceramics have been prepared by a hydrothermal method. Low-temperature sintering of $Mg_4(Nb_{2-x}V_x)O_9$ (MNV) by V substitution for Nb was discussed in this study. A $Q{\cdot}f_0$ value of 103,297 GHz with a ${\varepsilon}_r$ of 12.56 and a ${\tau}_f$ of $-10.53\;ppm/^{\circ}C$ was obtained when x=0.0625 after sintering at $1100^{\circ}C$ for 5 h.

• Korean Chemical Engineering Research
• /
• v.49 no.2
• /
• pp.151-154
• /
• 2011

Catalytic activity such as conversion and selectivity on the phenol hydroxylation over TS-1 prepared by hydrothermal method and microwave heating method, respectively, was compared and discussed for understanding the dependence of solvent such as water, methanol, acetone, respectively, during phenol hydroxylation, with hydrogen peroxide. Basic physical properties such as XRD, EDS, SEM and $N_{2}$ adsorption/desorption were determined and compared. The relationship between catalytic activity and physical properties of TS-1 was explained.

• Clean Technology
• /
• v.21 no.3
• /
• pp.178-183
• /
• 2015

Lead molybdate (PbMoO₄) oxides were successfully synthesized using a conventional hydrothermal method and a microwave-assisted hydrothermal method. They were characterized by XRD, DRS, BET, Raman, SEM and PL. We also investigated the photocatalytic activity of these materials for the decomposition of Rhodamine B under UV-light irradiation. From XRD and Raman results, well-crystallized PbMoO₄ crystals have been successfully synthesized regardless of preparation method and had 42~59 nm particle size. The PbMoO₄ catalysts prepared using microwave-assisted process had the similar particle size and enhanced the photocatalytic activity when compared to that prepared by hydrothermal method. The PbMoO₄ catalysts prepared under the irradiation of microwave for 75 min showed the highest photocatalytic activity. The PL peaks appears at about 530 nm at all catalysts and it was also shown that the excitonic PL signal is proportional to the photocatalytic activity for the decomposition of Rhodamine B.

• Journal of the Korean Ceramic Society
• /
• v.36 no.4
• /
• pp.343-353
• /
• 1999

Microwave(2.45 GHz) was used as energy source in hydrothermal reaction to fabricate ultrafine BaTiO3 powder. Using microwave of 700 W, crytal BaTiO3 began to fom after 5 min in microwave-autoclave sys-tem. The crystallinity was not noticeably increased with increasing longer reaction time than 10 min. On the other hand in microwave-reflux system crytal BaTiO3 began to form after 15min and the crystallinity was not noticeably increased with increasing longer reaction time than 1hr,. In either case particle size dis-tribution was considerably uniform due to the effect of homogeneous heating by microwave. In addition mi-crowave heating gave an extremely small degree of particle agglomeration compared to electric heating. Av-erage sizes of as-synthesized powders were 30-60nm. Ba/Ti ratio in sol played an important role in det-ermining the particle size. It seems that excess barium forms different phases such as Ba(OH)2 which makes thin layer on the surface of BaTiO3 powder. This thin layer would inhibit the agglomeration of Ba-TiO3 powders and keep the small grain size. In microwave-autoclave system tetragonal-BaTiO3 was formed directly by the reaction of only 15 min. In the case of microwave-reflux system tetragonal-BaTiO3 was formed by driyng over 25$0^{\circ}C$.

• Korean Journal of Mineralogy and Petrology
• /
• v.33 no.3
• /
• pp.243-250
• /
• 2020

The purpose of this study is to find out the possibility of applying microwave-hypochlorous acid leaching to effectively leaching Au in hydrothermal minerals on board. The comparative leaching experiment were confirmed that the leaching rate of Au with(T1)/with out(T2) of microwave nitric acid leaching. In addition, the leaching rate of Au on the conventional leaching by mechanical agitation(T3) and microwave leaching was compared. The result of microwave nitric acid leaching(solid-liquid ratio; 10%, leaching temperature; 90 ℃, leaching time; 20 min) confined that the metal leaching rate was high in the order of As>Pb>Cu>Fe>Zn, and the content of Au in the leaching residue was increased from 33.77 g/ton to 60.02 g/ton. As a result of the comparative leaching experiment using a chloride solvent, the dissolution rate of Au was high in the order of T1(61.10%)>T3(53.30%)>T2(17.30%). Therefore, chloride, which can be manufactured using seawater and that can be recycled by collecting chlorine gas generated in the leaching process, is expected to be an optimal solvent for Au leaching. In addition, the application of microwaves is believed to be effective in terms of time, efficiency and energy.

• Journal of the Korean institute of surface engineering
• /
• v.56 no.6
• /
• pp.393-400
• /
• 2023

Acetone, a metabolite detected from the exhaled breath of people doing a diet, can be used for non-invasive monitoring of diet efficiency. Thus, gas sensors with rapid response and recovery characteristics to acetone need to be developed. Herein, we report ultrafast acetone sensors using Ce-doped In₂O₃ nanoparticles prepared by the one-pot microwave-assisted hydrothermal method. The pure In₂O₃ sensor shows a high response and fast response time (τ_res = 6 s) upon exposure to 2 ppm acetone at 300 ℃, while exhibiting a relatively sluggish recovery speed (τ_recov = 1129 s). When 20 wt% Ce is doped, the τ_recov of the sensor significantly decreased to 45 s withholding the fast-responding characteristic (τ_res = 6 s). In addition, the acetone response (resistance ratio, S) of the sensor is as high as 5.8, sufficiently high to detect breath acetone. Moreover, the sensor shows similar acetone sensing characteristics even under a highly humid condition (relative humidity of 60%) in terms of τ_res (6 s), τ_recov (47 s), and S (4.7), demonstrating its high potential in real applications. The excellent acetone sensing characteristics of Ce-doped In₂O₃ nanoparticles are discussed in terms of their size, composition, phase, and oxygen adsorption on the sensing surface.