• Composites Research
• /
• v.35 no.6
• /
• pp.469-476
• /
• 2022

In this paper, the microwave absorbing characteristics after the impact of the radar-absorbing structure (RAS) consisting of periodic pattern sheet (PPS) and glass fiber-reinforced plastic (GFRP) were experimentally investigated. The fabricated RAS effectively absorbed the microwave in the X-band (8.2-12.4 GHz). In order to induce the damage to the RAS, a low-velocity impact test with various impact energy of 15, 40, and 60 J was conducted. Afterward, the impact damage was observed by using visual inspection, non-destructive test, and image processing method. Moreover, the absorbing performance of intact and damaged RAS was measured by the free-space measurement system. The experiment results revealed that the delamination damage from the impact energy of 15 J did not considerably affect the microwave absorbing performance of the RAS. However, fiber breakage and penetration damage with a relatively large damaged area were occuured when the impact energy was increased up to 40 J and 60 J, and these failures significantly degraded the microwave absorbing characteristics of the RAS.

• Journal of the Korean Magnetics Society
• /
• v.5 no.5
• /
• pp.805-809
• /
• 1995

In order to widen the band-width of ferrite absorber, compositional effect on the complex permeability of Ni-Zn ferrite and the structure of grid absorber were studied. From the experimental results, we could determine the optimum composition composition of Ni-Zn ferrite and the structure of grid absorber. Also, we manufactured grid absorber and investigated its microwave absorbing characteristics. Calculation shows that the ferrite frid absorber suppresses reflection ${\leq}-20dB$ from 30 MHz to 700 MHz and the conventional ferrite tile absorber suppresses reflection ${\leq}20dB$ in the frequency range of 30 MHz-400 MHz. It was found that the microwave absorbing performance of the ferrite grid absorber was superior to the ferrite tile absorber.

• Journal of Aerospace System Engineering
• /
• v.4 no.3
• /
• pp.24-28
• /
• 2010

The purpose of this study is to define available microwave absorbing structure for aircraft from in the X-band(8.2~12.4GHz) frequencies. The electromagnetic wave absorption or shielding techniques is an important issue not only for military purpose but also for commercial purposes. Aircraft Radar Absorbing Structure(RAS) is absorbed or scattered propagation waves from the enemy radar. There are absorbing technologies at shaping design techniques and using Radar Absorbing Materials(RAM). RAM is more important because shaping design can't include perfect radar absorbing performance. In this study, based on material properties was introduced RAM and to analyze the each characteristics. Finally, we comparison appropriate RAM for aircraft.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.5
• /
• pp.869-874
• /
• 2010

A research for the optimal design of microwave absorbing material featuring for the broadband has been conducted to apply to warship. A multilayered structure was suggested using wave absorbing layers and resistance layer to perform high performance in broadband frequencies. For the optimization of the wave absorbing characteristics, the thickness and permittivities of the absorbing layers as well as the surface resistance of the resistant layer were determined using genetic algorithm. The data base of permittivities related to the density of the dielectric materials and loss materials was obtained by the experiments for the dielectric constants of the absorbing layers, furthermore, the results were numerically expressed and used for the optimization.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.6
• /
• pp.1002-1008
• /
• 2001

The absorbing structure composed of multi-layered fiber reinforced composite materials was designed and microwave absorbing properties are investigated. On the basis of transmission line theory, the theoretical equations to predict the reflection loss and the appropriate composite material for each functional layer are suggested. The most significant result of this study is the successful design and fabrication of triple-layered composite laminates which has the superior microwave absorbing porperties (more than 10 dB in 4∼12 GHz range), without using the ferrite filler in the impedance transforming layer. In the two-layered composite laminate (absorber/substrate), however, the use of ferrite filler (about 40 wt %) in the absorbing layer is necessary to obtain the certain level of microwave absorbance. By combining the glass-fiber composite with ferrite filler and carbon-fiber composite substrate, the microwave absorbing properties more than 10 dB in 4∼12 GHz frequencies than be obtained.

• Composites Research
• /
• v.27 no.6
• /
• pp.225-230
• /
• 2014

In this study, a novel microwave absorber which consists of a structural part, a resistive sheet, and a low dielectric layer is proposed. Unlike the conventional Salisbury screen, a newly proposed absorber is capable of a range of absorbing performance, from narrowband to broadband. In the case of the narrowband absorber, the fabricated absorber with optimized design parameters has a strong resonance at 9.25 GHz and reflection loss of -44 dB with satisfying the -10 dB absorption in whole X-band (8.2 GHz~12.4 GHz). For the broadband absorber design, the reflectivity was minimized in the considered frequency ranges. The designed absorber showed two weak resonances near 6.5 GHz and 16.5 GHz and satisfied the -10 dB absorption from C-band to Ku-band (4 GHz~18 GHz). The measured reflection loss of fabricated absorber was well matched with simulation results, though the measurement was only performed on X-band. For the Salisbury screen to be capable of broadband absorption, it should be stacked multiply in a structure known as the Jaumann absorber. However, for the microwave absorber presented here, broadband as well as narrowband capabilities can be implemented without a change of the structure.

• Composites Research
• /
• v.29 no.3
• /
• pp.98-103
• /
• 2016

This paper deals with the fabrication and verification of the microwave absorbing structure using semiconductive fiber reinforced composite. Two kinds of fiber were used to fabricate composites. Electromagnetic properties of the composites were measured by freespace measurement system over X-band. Two single slab absorbers and a double slab absorber were designed by thickness optimization method. Single slab absorbers did not show good microwave absorption performance because the permittivity is away from non-reflection curve. Double slab absorber complemented the limitations on single slab absorber and it showed good microwave absorption performance. Double slab absorber showed -43.9 dB loss near 10 GHz.

• Korean Journal of Materials Research
• /
• v.12 no.6
• /
• pp.442-446
• /
• 2002

Design of microwave absorbers using high frequency properties of fiber reinforced composites are investigated. Two kinds of composite materials (glass and carbon) are used and their complex permittivity and permeability are measured by transmission/reflection technique using network analyzer. Low dielectric constant and nearly zero dielectric loss are determined in glass fiber composite. However, carbon fiber composites show the high dielectric constant and large conduction loss which is increased with anisotropy of fiber arrangement. It is, therefore, proposed that the glass and carbon fiber composites can be used as the impedance transformer (surface layer) and microwave reflector, respectively. By inserting the foam core or honeycomb core (which can be treated as an air layer) between glass and carbon fiber composites, microwave absorption above 10 dB (90% absorbance) in 4-12 GHz can be obtained. The proposed fiber composites laminates with sandwitch structure have high potential as lightweight and high strength microwave absorbers.

• Journal of the Korean Magnetics Society
• /
• v.15 no.5
• /
• pp.282-286
• /
• 2005

Ni-Cu-Zn ferrites were prepared by the co-precipitation and ferrite microwave absorbers on low temperature sintering were investigated in this work. The properties of its microwave absorbing and physical were analyzed into variations of Ni addition, calcination temperature, sintering temperature. From the analysis of X-ray diffraction patterns, we can see that all the particles have only a single phase spinel structure. In addition, the powders particle size distribution obtained the nano size. By increasing the Ni additive, the permeability of the powders was decreased and the loss factor increased at sintering temperature $1100^{\circ}C$. Also, we considered that it can used high frequency rage. We found that the $(Ni_{0.7}Cu_{0.2}Zn_{0.1}O)_{1.02}(Fe_{2}O_3)_{0.98}$ appeared microwave absorbing properties better than other composition.

• Journal of the Korean Magnetics Society
• /
• v.11 no.1
• /
• pp.14-20
• /
• 2001

The structure, shape, size, and magnetic properties of Ni$_{0.5}$Cu$_{0.1}$Zn$_{0.4}$Fe$_2$O$_4$ have been investigated as a function of annealing temperatures. In order to control the microwave absorbing properties of ferrite-rubber composite and the complex losses (magnetic loss and conduction loss), the effect of carbon addition was also studied. It was found that the coercive force decreased with increasing heat-treatment temperatures. Relative complex permeability and reflection loss were measured by the network analyzer. As a result, the natural resonance occurred in the low frequency tinge, and the matching frequency of the ferrite-rubber composite prepared at 130$0^{\circ}C$ was found to be lower. As heat-treatment temperatures were increased, the magnetic loss ($\mu$$_{r}$", $\mu$$_{r}$′) and the dielectric loss ($\varepsilon$$_{r}$"/$\varepsilon$$_{r}$′) were increased. It was caused that the absorption characteristics of the absorber were improved. The conduction loss and magnetic loss were expected to be occurred together because two matching frequencies were shown with carbon addition. It was confirmed that the matching frequency of the microwave absorber could be controlled by controlling heat-treatment temperatures and carbon additions.ons.tions.