• Journal of Welding and Joining
• /
• 제5권2호
• /
• pp.27-34
• /
• 1987

The characteristics of arc sprayed layer were studied with hardness test and microstructural observation. The erosion resistance of arc sprayed layer was also evaluated using a method of steel ball blasting test which was proposed in this study as a test method for measuring the erosion properties in the impact wear condition. By an impact of the molten droplets on the redeposited substrate, lamella structure was formed which contains laminated oxide layers, fissures, and porosities. As a result of mechanical tests, it was shown that the sprayed specimen showed higher hardness than the substrate, but it resulted in higher erosion rate than the substrate. The poor erosion property obtained with a sprayed coating was considered to be attributable to easy flaking off the the layers laminated with brittle oxide layers.

• Journal of Mechanical Science and Technology
• /
• 제14권9호
• /
• pp.978-984
• /
• 2000

The aim of this study is to investigate the ductile fracture behaviour under Mode I loading using SA533B pressure vessel steel. Experiments consist of the Round Notch Bar Test (RNB), Single Edge Crack Bending Test (SECB), and V-Notch Bar Test (VNB). Results from the RNB test were used to tune the damage modelling constant. The other tests were performed to acquire the J-resistance curves and to confirm the damage constants. Microstructural observation includes the measurement of crack profile to obtain the roughness parameter. Finally, simulation using Rousellier Ductile Damage Theory (RDDT) was carried out with 4-node quadrilateral element ($L_c=0.25\;mm$). For the crack advance, the failed element removal technique was adopted with a ${\beta}$ criterion. In conclusion, the predicted simulation using RDDT showed a good agreement with the experimental results. A trial using a roughness parameter was made for a new evaluation of J-resistance curve, which is more conservative than the conventional one.

• 비파괴검사학회지
• /
• 제28권3호
• /
• pp.285-291
• /
• 2008

We have experimentally investigated the cyclic deformation in copper using ultrasonic nonlinearity. The observation and characterization of dislocation substructure have been conducted using transmission electron microscope and electron backscattered diffraction technique. The ultrasonic nonlinearity (${\beta}/{\beta}_0$) was measured by the harmonic generation technique after various fatigue cycles. The microstructural effect on the nonlinearity was discussed regarding the extent of dislocation substructures evolved from low cycle fatigue. The ultrasonic nonlinearity of copper monotonically increased with the fatigue cycles due to the evolution of dislocation cell substructures.

• 분석과학
• /
• 제11권4호
• /
• pp.316-320
• /
• 1998

An image analysis was used for the interpretation of microstructures of ferrous metal artifacts. For the purposes, various microstructural features such as average grain size, phase area, shape factor, and composition of the inclusions, were parameterized for the information about manufacturing techniques such as casting, heating and tempering. The carbon content was determined through the evaluation of the amount of pearlite phase. As the amount of pearlite phase increased the shape factor also increased. Grain size was relatively smaller in trans-section than in cross-section. The manufacturing direction was trans-sectional because the orientation of inclusions was elongated lengthwise. All inclusions was of silicate groups and the manufacturing temperature was estimated up to $1450^{\circ}C$.

• 한국세라믹학회지
• /
• 제36권6호
• /
• pp.662-670
• /
• 1999

Porous alumina was fabricated from pressureless powder packing forming method using powders granulated by spray drying. It was investigated the pore size distribution of fabricated porous alumina. The results of microstructural observation showed that intraganular pore size and intragranular pore size. At 1700$^{\circ}C$ there were no intragranular pores but it showed homogeneous distribution of intergranular pore size. The bending strength and shrinkage increased as porosity decreased. In case of thermal shock resistance sudden decrease of bending strength to $\Delta$T was not shown because intergranular large pore prevented sudden crack propagation.

• 한국세라믹학회지
• /
• 제34권5호
• /
• pp.500-504
• /
• 1997

Perovskite Pb0.7Ba0.3Zn1/3Nb2/3O3 substituted with 0.3 mole fraction for Pb-site in PbZn1/3Nb2/3O3 relaxor and pyrochlore Pb1.83Ba0.29Zn1.71Nb2/3O6.39 were mixed and dielectric characteristics of this composites were investigated. Percolation limit of perovskite phase, which was determined by microstructural observation in the composite as an isolation of perovskite phase from pyrochlore matrix, was 28.9-47.5 vol%. Ferroelectric phase transition below percolation limit depends on a parameter which affects the propagation of lattice vibration between isolated perovskite phase and pyrochlore matrix. Therefore, it is believed that ferroelectric lattice vibration of isolated perovskite phase could be transfered to pyrochlore matrix when the oxygen octahedra are linked in 3-dimension and highly polarizable Pb2+ ions are contained in both phases.

• 한국주조공학회지
• /
• 제29권6호
• /
• pp.251-256
• /
• 2009

The effect of austempering treatment on mechanical properties of nodular indefinite chilled iron(NICI) and ductile cast iron(DCI) was investigated. In microstructural observation, matrix phase(pearlite and ferrite) was changed to ausferrite after austempering treatment both DCI and NICI. In case of NICI, decomposition of cementite($Fe_3C$) during austempering treatment was induced. After austempering treatment, mechanical properties such as hardness, tensile strength and impact toughness was improved in NICI and DCI. The wear resistance is slightly decreased because of decomposition of cementite during austempering treatment in NICI but impact toughness and strength is dramatically increased.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 1997년도 춘계학술대회논문집
• /
• pp.175-178
• /
• 1997

A modified Mukerjee's model considering the microstructural evolution was developed to study the superplastic bulge forming process of Ti-6Al-4V alloy. Through the microstructual observation after deformation, it was found that the grain growth rate of uniaxially tested specimens was different from that of biaxially deformed specimens. From this result, bulge forming experiments with and without back pressure were performed to examine the grain growth behavior and to compare the results of biaxial test with those of triaxial test. Good agreement between the prediction by a modified Mukerjee's model and the experimental measurements was obtained for bulge profile and thickness distribution.

• 한국세라믹학회지
• /
• 제30권1호
• /
• pp.78-84
• /
• 1993

In PMN-pyrochlore phase mixtures, dielectric constant was measured as a function of the volume fraction of pyrochlore phase and considered with general effective media(GEM) equation. For the application of GEM equation to this system, the critical volume fraction(Vc) where connectivity between the perovskite PMN and pyrochlore phase changed from 0-3 to 3-3, was determined based on the each particle size ratio of two phases with microstructural observation. And then the t value was determined from modified percolation powder-law dependence ( K-Kc (V-Vc)t). In the case of applying such values of t and Vc to the GEM equation, which provided a reasonable fit to the measured dielectric constant within the experimental error range.

• Advances in materials Research
• /
• 제9권3호
• /
• pp.171-187
• /
• 2020

The microstructural evolution of different compositions of Mg-Sn alloys (30%Sn-70%Mg, 40%Sn-60%Mg and 50%Sn-50%Mg) is studied at first to understand the changes observed with change in tin content and deformation conditions. The Mg₂Sn phase increases with increase in tin content and a significant substructure development is found in 50%Sn-50%Mg alloy. The above observation led to further deformation studies on Mg₂Sn based thermoelectric materials with higher tin percentage. The microstructure in terms of Electron backscatter diffraction (EBSD)measurements is studied in detail followed by the determination of thermoelectric properties i.e., Seebeck coefficient and electrical conductivity for both as cast and extruded Mg_(2+x)Sn-Ag alloys. The electrical conductivity of the extruded Mg_(2+x)Sn-.3wt%Ag {x =1} alloy was found to be more than its as cast counterpart while the Seebeck coefficient values remained almost the same.