• Advances in materials Research
• /
• 제12권4호
• /
• pp.263-271
• /
• 2023

In this study, AA1060/Alumina composites were fabricated by combined stir casting and accumulative press bonding (APB). The APB process was repeated up to six press bonding steps at 300Ċ. As the novelty, potential dynamic polarization in 3.5Wt% NaCl solution was used to study the corrosion properties of these composites. The corrosion behavior of these samples was compared and studied with that of the annealed aluminum alloy 1060 and versus the number of APB steps. So, as a result of enhancing influence on the number of APB process, this experimental investigation showed a significant enhancement in the main electrochemical parameters and the inert character of the Alumina particles. Together with Reducing the active zones of the material surfaces could delay the corrosion process. Also, at higher number of steps, the corrosion resistance of composites improved. The sample produced after six number of steps had a low corrosion density in comparison with high corrosion density of annealed specimens. Also, the scanning electron microscopy (SEM), was used to study the corrosion surface of samples.

• 한국진공학회지
• /
• 제15권2호
• /
• pp.173-179
• /
• 2006

Pulsed laser deposition 방법으로 증착한 $PbZr_{0.3}Ti_{0.7}O_{3}$ (PZT)박막의 구조적, 전기적 성질에 대한 연구를 하였다. PZT 박막은 $LaAlO_3$ 기판위에 동일한 조건으로 증착된 $LaMnO_3$ (LMO) 산화물을 하부 전극으로 하여 증착시간을 변화시키며 증착하였다. High-resolution x-ray diffraction 결과를 통해 LMO 하부 전극과 PZT 박막이 방향성 있게 자란 것을 확인할 수 있었고 박막의 두께는 field-emission scanning electron microscope을 통하여 측정할 수 있었다. 또한 우리는 atomic force microscopy을 이용하여 박막의 표면 거칠기를 구하였고 국소적인 범위의 전기적 특성은 piezoelectric force microscopy 모드를 이용하여 측정하였다. 그 결과 PZT/LMO 구조는 나노 스토리지의 미디어로 쓰이기 위해 필요한 성질들을 갖추었음을 알 수 있었다.

• Bulletin of the Korean Chemical Society
• /
• 제35권12호
• /
• pp.3553-3558
• /
• 2014

The reduced graphene oxide(rGO)/aluminum phosphate($AlPO_4$)-coated $LiMn_{1.5}Ni_{0.5}O_4$ (LMNO) cathode material has been developed by hydroxide precursor method for LMNO and by a facile solution based process for the coating with GO/$AlPO_4$ on the surface of LMNO, followed by annealing process. The amount of $AlPO_4$ has been varied from 0.5 wt % to 1.0 wt %, while the amount of rGO is maintained at 1.0 wt %. The samples have been characterized by X-ray diffraction, scanning electron microscopy, and high-resolution transmission electron microscopy. The rGO/$AlPO_4$-coated LMNO electrodes exhibit better cyclic performance compared to that of pristine LMNO electrode. Specifically, rGO(1%)/$AlPO_4$(0.5%)- and rGO(1%)/$AlPO_4$(1%)-coated electrodes deliver a discharge capacity of, respectively, $123mAhg^{-1}$ and $122mAhg^{-1}$ at C/6 rate, with a capacity retention of, respectively, 96% and 98% at 100 cycles. Furthermore, the surface-modified LMNO electrodes demonstrate higher-rate capability. The rGO(1%)/$AlPO_4$(0.5%)-coated LMNO electrode shows the highest rate performance demonstrating a capacity retention of 91% at 10 C rate. The enhanced electrochemical performance can be attributed to (1) the suppression of the direct contact of electrode surface with the electrolyte, resulting in side reactions with the electrolyte due to the high cut-off voltage, and (2) smaller surface resistance and charge transfer resistance, which is confirmed by total polarization resistance and electrochemical impedance spectroscopy.

• Korean Chemical Engineering Research
• /
• 제51권5호
• /
• pp.540-544
• /
• 2013

고분자전해질연료전지(PEMFC)는 시동/정지과정에서 성능과 수명이 감소한다. 본 연구에서는 캐소드가스로 산소를 사용하는 데드엔드 형 PEMFC의 시동/정지 과정의 영향을 분극곡선, 임피던스(EIS), SEM과 TEM을 사용해 연구하였다. 시동/정지 과정에서 PEMFC 성능감소를 막기 위해서는 더미 로드를 사용해야 함을 보였다. 시동/정지 반복과정 중 50% 상대습도(RH)에서 캐소드 카본지지체의 부식에 의한 열화가 100% RH보다 심했다. 데드엔드 형 PEMFC의 정지과정에서 PEMFC에 물을 공급해줌으로써 50% RH에서 열화속도를 감소시켰다.

• 한국진공학회지
• /
• 제17권1호
• /
• pp.28-33
• /
• 2008

R.F 마그네트론 스퍼터링 방법을 이용하여 Indium tin oxide(ITO)가 증착된 유리기판 위에 PLZT ($Pb_{1.1}La_{0.08}Zr_{0.65}Ti_{0.35}O_3$) 박막을 제작하였다. 기판온도를 $500^{\circ}C$로 고정하여 증착한 후 급속열처리 방법으로 다양한 온도 ($550-750^{\circ}C$)에서 후열처리 하였다. 후열처리온도의 변화에 따른 PLZT 박막의 결정학적 특성을 X선 회절법을 통하여 분석하였고 원자간력 현미경을 이용하여 박막의 표면 상태를 관찰하였다. 또한 precision material analyzer 을 이용하여 분극이력곡선과 피로특성을 측정하였다. 후 열처리 온도가 증가함에 따라 잔류분극 값(Pr)은 $10.6{\mu}C/cm^2$ 에서 $31.4{\mu}C/cm^2$로 증가하였으며 항전계(Ec)는 79.9 kV/cm에서 60.9 kV/cm로 감소하는 경향을 보였다. 또한 피로특성의 경우 1MHz 주파수에서 ${\pm}5V$의 square wave를 인가하여 측정한 결과 $700^{\circ}C$에서 후열처리한 시편의 경우 $10^9$회 이상의 분극반전을 거듭하였을 때 분극값이 15% 감소하는 결과를 나타내었다.

• Bulletin of the Korean Chemical Society
• /
• 제33권5호
• /
• pp.1566-1570
• /
• 2012

The combined use of indium and polysorbate 20 (Tween 20) was considered as a new inhibition technique for zinc corrosion. Zn and Zn-In alloy coatings were prepared by electrodeposition and their morphology and composition were characterized by scanning electron microscopy (SEM) and inductively coupled plasma atomic emission spectrometry (ICP-AES). The corrosion inhibition effect of indium and Tween 20 on zinc was investigated by polarization curves and electrochemical impedance spectroscopy (EIS). The corrosion inhibition efficiencies obtained from Tafel and EIS analyses are well in agreement. Zinc corrosion can be inhibited to some extent by the individual use of indium and Tween 20 and higher corrosion inhibition efficiency can be obtained by the combined use of indium and Tween 20.

• 전기화학회지
• /
• 제13권4호
• /
• pp.246-250
• /
• 2010

In this study, nano-crystallized $Al_2O_3$ was coated on the surface of $LiFePO_4$ powders via a novel dry coating method. The influence of coated $LiFePO_4$ upon electrochemical behavior was discussed. Surface morphology characterization was achieved by transmission electron microscopy (TEM), clearly showing nano-crystallized $Al_2O_3$ on $LiFePO_4$ surfaces. Furthermore, it revealed that the $Al_2O_3$-coated $LiFePO_4$ cathode exhibited a distinct surface morphology. It was also found that the $Al_2O_3$ coating reduces capacity fading especially at high charge/discharge rates. Results from the cyclic voltammogram measurements (2.5-4.2 V) showed a significant decrease in both interfacial resistance and cathode polarization. This behavior implies that $Al_2O_3$ can prevent structural change of $LiFePO_4$ or reaction with the electrolyte on cycling. In addition, the $Al_2O_3$ coated $LiFePO_4$ compound showed highly improved area-specific impedance (ASI), an important measure of battery performance. From the correlation between these characteristics of bare and coated $LiFePO_4$, the role of $Al_2O_3$ coating played on the electrochemical performance of $LiFePO_4$ was probed.

• Corrosion Science and Technology
• /
• 제18권6호
• /
• pp.267-276
• /
• 2019

The purpose of this study was to examine the influence of conditions for quenching and/or tempering on the corrosion and hydrogen diffusion behavior of ultra-strong automotive steel in terms of the localized plastic strain related to the dislocation density, and the precipitation of iron carbide. In this study, a range of analytical and experimental methods were deployed, such as field emission-scanning electron microscopy, electron back scatter diffraction, electrochemical permeation technique, slow-strain rate test (SSRT), and electrochemical polarization test. The results showed that the hydrogen diffusion parameters involving the diffusion kinetics and hydrogen solubility, obtained from the permeation experiment, could not be directly indicative of the resistance to hydrogen embrittlement (HE) occurring under the condition with low hydrogen concentration. The SSRT results showed that the partitioning process, leading to decrease in localized plastic strain and dislocation density in the sample, results in a high resistance to HE-induced by aqueous corrosion. Conversely, coarse iron carbide, precipitated during heat treatment, weakened the long-term corrosion resistance. This can also be a controlling factor for the development of ultra-strong steel with superior corrosion and HE resistance.

• 한국전기화학회:학술대회논문집
• /
• 한국전기화학회 2002년도 연료전지심포지움 2002논문집
• /
• pp.211-218
• /
• 2002

In this study, Pt/Pd (1.1), PtPd (2:1) and PtPd (3:1) binary catalysts and Pt/Ru/Pd (5:4:1) ternary catalyst were designed. The catalysts were synthesized by impregnation method using $NaBH_4$ as a reducing agent. A good catalyst for methanol oxidation requires low on-set potential, stable durability and low activation energy. In order to investigate the catalytic activity for the methanol oxidation, electrochemical measurements such as cyclic voltammetry and chronoamperometry were peformed in sulfuric acid with/without methanol solution. In order to calculate the activation energy of the reaction, electrochemical measurements were also tested at different temperatures. For investigation of the structural analysis such as particle size and alloying, X-ray diffraction and transmission electron microscopy analysis were used. In order to identify the role of the Pd and to determine the composition of the surface of the Pt/Pd nanoparticles, X-ray photoelectron spectroscopy (XPS) analysis was investigated. The XPS spectra of Pd showed that Pd appears only as a metallic state in the binary catalysts. The chemical states of Pt in PtPd catalysts are both metallic and oxidative. Polarization curves and power density data were obtained by testing the DMFC unit cell performance of PtPd and PtRuPd catalysts. These data showed that Pt/Pd (2:1) and Pt/Ru/Pd (5:4:1) have better performance than Pt and Pt/Ru, respectively.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.570-573
• /
• 2002

Pb(Zr0.52Ti0.48)O3 (PZT) thin films were deposited on the Pt/Ti bottom electrode by rf magnetron sputtering method from target containing 5%, 25% and 50% Pb excess for applying ferroelectric random access memory (FRAM). PZT films were deposited at $300^{\circ}C$ and then they were crystallized by rapid thermal annealing (RTA) at $700^{\circ}C$. After RTA treatment, our results showed that all PZT films indicated perovskite polycrystalline structure with preferred orientation (110) and no pyrochlore phase was observed by X-ray diffraction (XRD) and by Scanning electron microscopy (SEM). A well-fabricated PZT film of excess Pb 25% capacitor showed a leakage current density in the order of $2.63{\times}10^{-7}A/cm^2$ at 100kV/cm, a remanent polarization of $3.385{\mu}C/cm^2$ and a coercive field of 41.32 kV/cm. The results showed that Pb excess of target affects to electrical properties of PZT thin film.