• Proceedings of the IEEK Conference
• /
• 2002.06b
• /
• pp.333-336
• /
• 2002

This paper purpose design and implementation of system bus for the effective interconnection between peripheral device and 32-bit microprocessor. The designed system bus support general bus protocol. Also, it is optimized for 32-bit microprocessor. It is divided into two system. high performance system bus and Peripheral system bus.

• The Journal of Information Technology
• /
• v.9 no.1
• /
• pp.33-39
• /
• 2006

This study is for the contents of development to the hardware system and software driving algorithm to implement the frequency band of about 7KHz los pass digital filter which has the cut-off frequency of 392Hz by interfacing of a microprocessor with its peripheral analog-to-digital converter chip and digital-to-analog converter chip. The simplicity of digital filter design without difficulty and the implementation of programmed digital filter can be realized by providing the interfacing method to implement the law pass digital filter for the biological signals and the realization method of computer algorithm by a microprocessor.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.41 no.3
• /
• pp.281-291
• /
• 1992

This paper deals with the digital autopilot implementation for a launch vehicle. We propose a hardware and software system for digital autopilot implemented by microprocessor. The hardware system designed in this paper consists of CPU and memory board with 80286 MPU and 80287 NPU and I/O interface with A/D and D/A converters. The software system developed is composed of power-on self-test program, initializing program, interrupt service program, and control program. The performance of the overall system controlled by the digital autopilot implemented in this paper is evaluated via real-time simulations, which show that the control performances are satisfactory.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.4 no.1
• /
• pp.283-288
• /
• 2000

This paper proposes a novel Pulse Width Modulation (PWM) method for microprocessor implementation of full-bridge PWM inverters. In the method, the period of unipolar full-bridge inverters is divided equally into the frequency modulation ratio and the reference fundamental amplitude and the inverter output fundamental amplitude are compared. Using this method, the turn-on time computation of each interval is very favored for the microprocessor implementation. The harmonic analysis shows that the harmonics can be ignored when the modulation ratio is enough large. The simulation and experimental results show the effectiveness of the proposed algorithms.

• Proceedings of the IEEK Conference
• /
• 2003.07c
• /
• pp.2637-2640
• /
• 2003

In this paper, we propose a simple and efficient data input/output block with high speed between Motorola MPC8XX microprocessor and memory devices. Proposed method is capable of high speed data read and write using the address decoder and the burst cycle between Motorola PowerPC based MPC8XX microprocessor and fixed address locating memory devices such as FIFO, PCMCIA card, and so on. Experimental results are given our findings and discussions.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.14 no.6
• /
• pp.455-462
• /
• 2004

This paper is concerned with the implementation of the active vibration suppression controller using analog circuit and microprocessor. The target active vibration controller is the positive position feedback(PPF) controller since it provides a simple algorithm suitable for both analog circuit and digital controllers. In this study, the analog PPF controller is realized using an operational amplifier and the digital PPF controller is realized using a low-cost micro-controller. The circuit diagrams are explained in detail. We then discuss the advantages and disadvantages of both methods from the view of practical implementation. Experimental results show that both implementation methods can be effectively used for the active vibration control but need to be chosen based on the mission objective.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.3
• /
• pp.35-41
• /
• 1981

In this paper, the application of model reference adaptive control theory to the D.C motor speed control using the microprocessor is studied. It is shown that with the use of an adaptive control algorithm the error between output of the motor and the reference model, which is approximated to first order, can be conve to zero. By computer simulation and the practical implementation with the microprocessor M 6800, can be concluded that the adaptive control system adapts well to the rapid change of the load and reference inputs.

• Journal of Advanced Marine Engineering and Technology
• /
• v.16 no.4
• /
• pp.102-112
• /
• 1992

The three-phase full(6-pulse) bridge controlled rectifier is one of the most widely used types of solid-state converters in DC drive applications for higher performance. In most of the previous designs, the gate control circuits of the converter have been designed with analog method which can be easily affected by noise. Nowdays with advances of microelectronics and power electronics, microprocessor and pheripal LSIs are increasingly used for eliminating this problems. In this paper, a novel general-purpose microprocessor -based firing system and control scheme for a three-phase controlled rectifier bridge has been developed and tested. Using the phase relations between ${\Delta}$-Y transformer in power operation part, gate pulse of the converter is generated with real time process so that microprocessor may share its time to control algorithms efficiently. The firing angle of the converter is smoothly controlled in the range of 0 $^{\dirc}$ to 180$^{\dirc}$ with a fast respone and a constant open loop gain, even for the case where the converter is fed by a weak AC system of unregulated frequency. The hardware and software control circuit implementation built around a 80286 microprocessor is discussed, and the experimental results are given. This scheme uses less hardware components and has higher dynamic performance in variable speed DC drive applications.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.8
• /
• pp.109-115
• /
• 2005

This paper addresses the CAN based networked intelligent multi-motor control system using DSP2812 microprocessor. CAN built in DSP2812 microprocessor is used to control and monitor the multi-motor system with the inverter driving system CAN network implementation schemes and the algorithm for multi-motor control and monitoring is also developed. We configure the multi-motor control experimental system to verify the proposed algerian and the reliability of CAN networks system in the various operation of two induction motors. The experimental results show that CAN based networked intelligent multi-motor control system using DSP2812 microprocessor can carry out the real-time network based control in various speed range and the position control of induction motors.

• Journal of Industrial Technology
• /
• v.30 no.B
• /
• pp.119-123
• /
• 2010

LC-3 is an educational microprocessor for processor logic design, instruction execution fundamentals, and assembly language programming. This paper presents an IDE software, LIDE (LC-3 Integrated Development Environment), which integrates assembly program editor, LC-3 assembler, and LC-3 simulator.