• Journal of the Korean Society for Heat Treatment
• /
• v.16 no.2
• /
• pp.83-89
• /
• 2003

As a research for developing fine-grained high strength low carbon steels, the effects of austenitization temperature and hot deformation on microstructure was investigated in 0.15 wt.% carbon steels with microalloying elements such as Nb and Ti. When the steels were reheated at $1250^{\circ}C$, Nb containing steel showed very coarse austenite grain size of $200{\mu}m$ whereas Nb-Ti steel did fine one of $70{\mu}m$ because Ti carbonitrides could suppress the austenite grain growth. In case of 50% reduction at $850^{\circ}C$, the austenite grains in the Nb steel partially recrystallized while those in the Nb-Ti steel fully recrystallized probably due to finer prior austenite grains.For the Nb-Ti steel, ferrite grain size was not sensitively changed with austenitization temperature and compression strain and, severe deformation of 80% reduction was not essentially necessary to refine ferrite grains to about $3{\mu}m$ which could be obtained through lighter deformation of 40% reduction.

• 한국기계연구소 소보
• /
• s.16
• /
• pp.29-39
• /
• 1986

Several heat treatment were applied to on HSLA steel of type StE47 (German standard) to produce five ferrite microstructures of different strength and at least two different grain sizes respectively. Whereas the ferrite microstructure had a strong influence on yield strength the effect of grain size was negligible. The different strength levels could be explained by regarding the arrangement of dislocations and vanadium carbide particles, and their mutual interaction. Specimens tranformed at $600^{\circ}C$ showed the highest strength levels. In this case precipitation has occured after the $\gamma$- $\alpha$ transformation. Very small VC particles are arranged mostly along dislocation lines. Increasing both, grain size and pearlite volume fraction leads to a remarkable shift of transition temperature which was further enhanced by increasing ferrite strength.

• Journal of the Korean Society for Heat Treatment
• /
• v.13 no.5
• /
• pp.346-354
• /
• 2000

Effect of Nb addition on the phase transformation behavior was studied through continuous cooling transformation tests after reheating(reheating CCT) and deforming(deforming CCT) the 0.07%C-1.3%Mn-0.015%Ti-(0~0.08)% Nb steels. Transformation temperatures for deforming CCT were lower than those for reheating CCT, and the critical cooling rate for bainite transformation during deforming CCT was lower than that during reheating CCT. These enhanced hardenability for deforming CCT was considered to come from the sufficient solid solution of Nb in austenite during high temperature reheating before deformation. With Nb addition, the phase transformation temperature decreased, the bainite formation was enhanced, and the hardness of steel increased. Furthermore, these phenomena were more remarkable for deforming CCT than for reheating CCT. From the results, Nb-Ti bearing low carbon steel was considered to be a very favorable alloy system with good strength/toughness balance by recrystallization control rolling process.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.08a
• /
• pp.383-389
• /
• 1999

The purpose of this study was to investigate the effects of alloying and rolling condition on the mechanical properties and to develop high strength line pipe steels with good toughness. Tests were carried out by the laboratory experiments followed by mill trials and mass production. It was found that a small addition of microalloying elements, such as Nb, V with Mo or Ti remarkably increased the strength and toughness of hot strips. The optimum condition of thermomechanical rolling on low carbon microalloyed steel improved the toughness through the formation of a fine and uniform microstructure. Based on this mill trials following the fundamental research, the production technology of line pipe steels, grade X70∼X100 with high toughness, has been established. These grade steels exhibit excellent low temperature toughness (vTs= under -80$^{\circ}C$) and sufficient strength in both the base metal and the ERW seam weld position, respectively.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2009.05a
• /
• pp.35-36
• /
• 2009

Development trend and current status were surveyed for pre-heat-treated high strength cold heading quality (CHQ) wire and it's forming technology. Spheroidizing, quenching, and tempering heat treatments are eliminated by adapting the pre-treated wire, which could reduce energy consumption rate and green house gas emission rate during produce parts requiring high strength. There are some challenging problems to expand application area such as enhancing forming tool life, and preventing delayed failure. Domestic research movement concerning the development and application of the new high strength wire was introduced.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2005.05a
• /
• pp.321-324
• /
• 2005

The main purpose of the present study has been placed on investigating the effects of controlled rolling and cooling on the microstructures and mechanical properties of C-Si-Mn-V steels for cold forming. The steels were manufactured in vacuum induction melting(VIM) furnace and casted to 1.1ton Ingots and the ingots were forged to $\Box150$ billet. The forged billets were reheated in walking beam furnace and rolled to coil, the stocks were rolled by Controlled Rolling and Cooling Technology (CRCT), so rolled at low temperature by water spraying applied in rolling stage and acceleratly cooled before coiling. Rolled coils were cold drawed to the degree of $27\%$ of area reduction without heat treatment. Microstructual observation, tensile test, compression test and charpy impact tests were conducted. The mechanical properties of the steels were changed by area reduction of cold drawing and it is founded that there are optimum level of cold drawing to minimize compression stress for these steels. From the result of this study, it is conformed that mechanical properties and microstructure of C-Si-Mn-V steels for cold forming were enhanced by accelerated cooling and founded optimum level of cold drawing.

• Journal of the Korean Society for Heat Treatment
• /
• v.26 no.2
• /
• pp.59-65
• /
• 2013

The microstructures and hardness distributions of a large-sized high strength H-sectional steel with both V and Nb were systematically examined. The outer surface of the flange part was composed of martensite and bainite due to faster cooling, and had a high hardness value of approximately 310 Hv. However, the amounts of ferrite and pearlite increased and the hardness decreased with increasing the distance from the outer surface at the flange part, except the inner surface. High hardness value of about 290 Hv was measured at the upper surface of the web part having martensite and bainite. The hardness drastically decreased with increasing the web thickness, and then greatly rose again at the lower surface due to bainite formation caused by fast air cooling. The hardness of the flange part was higher than that of the web part due to the larger amount of low-temperature transformed phases, except for the lower surface of the web part. Nb-rich precipitates of 30 to 50 nm and V-rich precipitates less than 20 nm were observed at both flange and web parts. However, the particle size was smaller at the flange part than the web part, resulting in the higher strength of the flange part.

• Journal of Computational Design and Engineering
• /
• v.3 no.4
• /
• pp.337-348
• /
• 2016

An experimental approach is presented for the measurement of wear that is common in the threading of cold-forged steel. In this work, the first objective is to measure wear on various types of roll taps manufactured to tapping holes in microalloyed HR45 steel. Different geometries and levels of wear are tested and measured. Taking their geometry as the critical factor, the types of forming tap with the least wear and the best performance are identified. Abrasive wear was observed on the forming lobes. A higher number of lobes in the chamber zone and around the nominal diameter meant a more uniform load distribution and a more gradual forming process. A second objective is to identify the most accurate data-mining technique for the prediction of form-tap wear. Different data-mining techniques are tested to select the most accurate one: from standard versions such as Multilayer Perceptrons, Support Vector Machines and Regression Trees to the most recent ones such as Rotation Forest ensembles and Iterated Bagging ensembles. The best results were obtained with ensembles of Rotation Forest with unpruned Regression Trees as base regressors that reduced the RMS error of the best-tested baseline technique for the lower length output by 33%, and Additive Regression with unpruned M5P as base regressors that reduced the RMS errors of the linear fit for the upper and total lengths by 25% and 39%, respectively. However, the lower length was statistically more difficult to model in Additive Regression than in Rotation Forest. Rotation Forest with unpruned Regression Trees as base regressors therefore appeared to be the most suitable regressor for the modeling of this industrial problem.

• Journal of Welding and Joining
• /
• v.25 no.2
• /
• pp.62-69
• /
• 2007

A kinetic model fur the particle coarsening behavior was developed. The proposed model considered the critical particle size which can be derived from Gibbs-Thomson equation unlike the conventional approach. In this study, the proposed particle coarsening model was applied to study the coarsening behavior of titanium nitride (TiN particle) in microalloyed steel weld HAZ. Particle size distributions and mean particle size by the proposed model were in agreement with the experimental results. Meanwhile, using additivity rule, the isothermal model was extended to predict particle coarsening behavior during continuous thermal cycle.

• Korean Journal of Materials Research
• /
• v.4 no.3
• /
• pp.364-375
• /
• 1994

The microstructure of medium-carbon non-heat treated steels by air-cooling shows ferritepearlite structure. Compared to the conventional Q/T steels, the strength of these steels containing V, Nb and Ti are similar to Q/T steels. However, their toughness are inferior. In this study, the mechanical properties and microstructures of low-carbon Mo bearing steels produced by direct-quenching process were investigated. Especially, the effect of Mo on the direct-quenched steels was examined. The direct-quenched steels containing Mo were found to have higher strength and toughness. Mo seemed to be effective in producing the fine structure and dense precipitates because of decreasing transformation temperature. The best results were 1211 MPa in UTS and 127.5 J in toughness in the oil quenched 0.15C+O.llV+ 0.035Nb+ 1.81Mo steel. Compared to 0.4% C microalloyed steels, this results showed that UTS increased by 45% and toughness by 2 times.