• 한국광학회지
• /
• 제16권3호
• /
• pp.217-224
• /
• 2005

LCD Backlight에서 Micro Fresnel Lens Array (MFLA)가 결합된 도광판을 설계${\cdot}$분석하였다. MFLA가 적용된 도광판과 기존의 프리즘 형태의 도광판의 광학적 특성을 전산모의하여 비교한 결과를 나타내었다. MFLA를 이용한 도광판을 사용할 경우 기존의 LCD backlight 장치에서 필요로 했던 프리즘 필름을 대체할 수 있음을 보였다.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제48권9호
• /
• pp.662-664
• /
• 1999

We fabricated AC-TFEL device having cone-shaped Si micro-tip reflector array based on the process which have been conventionally employed for the Si-tip field emitter array in FED system. As a result, the AC-TFEL device having a new geometrical structure could generate well concentrated visible white-light from 3600 reflectors/pixel under bipolar pulse excitation mode only by edge-emission mechanism.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2003년도 하계종합학술대회 논문집 II
• /
• pp.727-730
• /
• 2003

Thin tin oxide film with nano-size particle was prepared on silicon substrate by hydrothermal synthetic method and successive sol-gel spin coating method. The fabrication method of tin oxide film with ultrafine nano-size crystalline structure was tried to be applied to fabrication of micro gas sensor array on silicon substrate. The tin oxide film on silicon substrate was well patterned by chemical etching upto 5${\mu}{\textrm}{m}$width and showed very uniform flatness. The tin oxide film preparation method and patterning method were successfully applied to newly proposed 2-dimensional micro sensor fabrication.

• Journal of Mechanical Science and Technology
• /
• 제19권8호
• /
• pp.1544-1553
• /
• 2005

In this article, a micro cantilever array actuated by PZT films is designed and fabricated for micro fluidic systems. The design features for maximizing tip deflections and minimizing fluid leakage are described. The governing equation of the composite PZT cantilever is derived and the actuating behavior predicted. The calculated value of the tip deflection was 15 ${\mu}m$ at 5 V. The fabrication process from SIMOX (Separation by oxygen ion implantation) wafer is presented in detail with the PZT film deposition process. The PZT films are characterized by investigating the ferroelectric properties, dielectric constant, and dielectric loss. Tip deflections of 12 ${\mu}m$ at 5 V are measured, which agreed well with the predicted value. The 18 ${\mu}l/s$ leakage rate of air was observed at a pressure difference of 1000 Pa. Micro cooler is introduced, and its possible application to micro compressor is discussed.

• Journal of Pharmaceutical Investigation
• /
• 제40권6호
• /
• pp.333-337
• /
• 2010

Combining cell- and gene-based therapy is a promising therapeutic strategy in regenerative medicine. The aim of this study was to develop genetically modified mesenchymal stem cell (MSC) aggregates using a poly(ethylene glycol) (PEG) hydrogel micro-well array technique. Stable PEG hydrogel micro-well arrays with diameters of 200 to $500\;{\mu}m$ were fabricated and used to generate genetically engineered MSC aggregates. Rat bone marrow-derived MSCs were transfected with a green fluorescent protein (GFP) plasmid as a reporter gene, and aggregated by culturing in the PEG hydrogel micro-well arrays. The resultant cell aggregates had a mean diameter of less than $200\;{\mu}m$, and maintained the mesenchymal phenotype even after genetic modification and cell aggregation. Transplantation of MSC aggregates that are genetically modified to express therapeutic or cell-survival genes may be a potential therapeutic approach for regenerative medicine.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 하계종합학술대회 논문집(2)
• /
• pp.21-24
• /
• 2002

A sensor array (35mm'! in diaphragm dimension) of 12 sensing elements with different operating temperatures was optimized with respect to thermal operation. This sensor array with single heater on a glass diaphragm over back-etched silicon bulk realizes a novel concept of a sensor array: an way of sensor elements operated at different temperatures can yield more information than single measurement. The proposed micro sensor array could provide well-integrated way structure because it has only single heater at the center of the diaphragm and used the various sensing properties of two kinds of metal oxide layers with various operating temperatures.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제50권6호
• /
• pp.271-275
• /
• 2001

We investigated preparation of 1-3 PZT composites for medical ultrasonic transducer array (briefly UTA) using micro pressing method. The proposed process was using pressing PZT green sheet by PMMA micro mold obtained from X-ray lithography. Microstructures, electriacl and electro-mechanical properties of fabricated composites were analyzed. Dielectric constant at 1kHz and thickness mode electro-mechanical coupling coefficient of $6.2mm{\times}6.2mm{\times}422{\mu}m$ UTA sample were 1754 and 51%, respectively. Microstructures of sintered PZT showed dense and uniform. And PZT phases were well crystallized. Micro pressing method is a mass productive process in case of using injection molded PMMA by batch type LIGA process.

• 대한전자공학회논문지SD
• /
• 제40권12호
• /
• pp.17-23
• /
• 2003

서로 다른 동작온도를 가지는 12개의 감지막으로 구성된 고집적형 센서어레이(다이아프램의 크기가 3×5㎟가 설계되고 열동작의 관점에서 최적화되었다. 이 센서어레이는 에칭된 실리콘기판과 접합된 얇은 유리기판 위의 중앙에 하나의 히터가 위치하고 양쪽에 동작온도가 다른 감지박막이 위치하도록 설계됨으로써 개별 마이크로센서 보다 동시에 훨씬 많은 정보를 얻을 수 있는 장점을 가지고 있다. 제안된 마이크로센서 어레이는 다이아프램의 중앙에 하나의 히터만을 가지는 구조를 하고 있기 때문에 고집적 어레이구조를 실현하면서도, 히터를 중심으로 감지박막의 동작온도에 따라 다양한 감지특정을 얻을 수 있다. 또 히터 양쪽의 감지박막의 종류를 다르게 함으로써 다이아프램위의 전 감지막이 모두 다른 감지특성을 가지게 되어 고집적 센서어레이를 구현하기 용이한 구조로 밝혀졌다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2002년도 춘계학술대회 논문집
• /
• pp.94-97
• /
• 2002

Micromolding methods are most suitable for mass production of plastic microlens and lens array with low cost. Among the procedures related with micromolding of microlens array, fabrication of mold insect which contains micro cavity of lens shape is the most important stage. In this study, nickel mold inserts for 45 $\mu\textrm{m}$ and 95 $\mu\textrm{m}$ diameters lens way were fabricated using electroforming process. The mother for metal mold inset was made using reflow method. A micro compression molding with polymer powders was used to test the qualities of the metal mold insets. Micro lens profile and surface roughness was measured by interferometric technique and AFM, respectively. The final molded lens replicated the mother well, and had good surface quality.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.934-937
• /
• 2001

It is well-known that the micro fabrication technology of micro parts are the high energy beam or silicon-based micro machining method such as LIGA Process, Laser machining, photolithography and etching technology. But, for fabricating complex 3-D structure it is better to use mechanical machining. This machining method by the mechanical machine tool with nanometer accuracy is getting attention in some field-especially micro optics machining such as grating, holographic lens, micro lens array, fresnel lens, encoder disk etc.. In this study, we survey the micro fabrication by mechanical cutting method and set up the mechanical micro machining system. And we carried out micro cutting experiments for micro parts with v-shape groove.