• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.366-370
• /
• 1997

This paper descibes a micro groove machining process on the polyurethane biopolymer by KrF excimer laser. To investigate the etch charcteristics of polyurethane biopolymer quantitatively,laser system for ablation was installed with high precison moter and then polymer ablation experiment, in which paramteters were fluence,pulse repetition rate,numbers of pulses and assist gas, was carred out. In this experiment, we found out that the value of critical energy density for ablation is 30mJ/cmsup2/ and the etching rate is more dependent on the pulse number and fluence than any other pamameter. Finally, we machined micro grooves for fiexibility as width 300.mu.m depth 100.mu.m and port for micro-devices mounting as length 100.mu.m width 300.mu.m depth .mu.m on the outer wallof polyurethane biopolymer tube which is used as medical device.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2004년도 하계학술발표 논문집
• /
• pp.170-170
• /
• 2004

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2019년도 춘계학술논문요약집
• /
• pp.65-66
• /
• 2019

• 한국압력기기공학회 논문집
• /
• 제20권1호
• /
• pp.16-24
• /
• 2024

Denting of steam generator (SG) tube is defined as the reduction in tube diameter due to the stresses exerted by the corrosion products formed on the outer diameter surface. This phenomenon is mostly observed in the crevices between SG tube and the top-of tubesheet or tube support plate. Despite the replacement of SG tube with Alloy 690, which has better corrosion resistance than Alloy 600, the denting of SG tube still remains a potential problem that could decrease the SG integrity. Deformation of SG tube by denting phenomenon can affect the surface properties and microstructure of SG tube. In this study, the effects of plastic deformation on surface properties and microstructure of Alloy 690 thermally treated (TT) tube was investigated by using the various analysis techniques. The plastic deformation of Alloy 690 increased the surface roughness and area. Many surface defects such as ripped surface and micro-cracks were observed on the deformed Alloy 690TT specimen. Based on the electron backscatter diffraction analysis, the dislocation density of deformed SG tube increased compared to non-deformed SG tube. In addition, the effects of changes in surface properties and microstructure of SG tube on general corrosion behavior were discussed.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2004년도 추계학술발표대회 개요집
• /
• pp.73-75
• /
• 2004

The purpose of this study is to optimize Nd:YAG laser welding parameters to seaz a Rf source into a Ti micro capsule. Ti tube ends can be sealed as some length of ぉbe end is melted and coalesced. The exact control of the melted length is the most important to get sound sealing. The Nozzle type, tube rotating speed, tilt angle, focal position, pumping voltage, pulse frequency and pulse width were selected as the Nd:YAG laser welding Parameters. These Parameters were optimized by the Taguchi experimental method using 115 orthogonal array. Appearance and cross section of the seated tube ends were examined by SEM.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1377-1380
• /
• 2008

An irradiation test of a nuclear fuel rod having external and internal tube structure was planned for a performance. To establish fabrication process satisfying the requirements of irradiation test, micro-TIG welding system for fuel rods was developed, and preliminary welding experiments for optimizing process conditions of fuel rod was performed. Fuel rods with 15.9mm diameter and 0.57mm wall thickness of cladding tubes and end caps have been used and optimum conditions of endcap welding have been selected. In this experiment, the qualification test was performed by tensile tests, helium leak inspections, and metallography examinations to qualify the endcap welding procedure. The soundness of the welds quality of a dual cooled fuel rods has been confirmed by mechanical tests and microstructural examinations.

• 한국유체기계학회 논문집
• /
• 제11권1호
• /
• pp.40-45
• /
• 2008

This paper proposes a tube pump composed of small-sized cams and followers for an implantable intrathecal drug infusion device. Each followers is driven by a cam and liquid is discharged by a sequential reciprocal motion of the followers. The advantage of this structure is that it allows the pump to be clean and valveless. To design a small-sized, low power pump some analysis were performed to determine the design parameters of the cam, follower and the tube. To verify the feasibility of the experiment, a prototype was manufactured and its operating characteristics were investigated. Experimental results were in accordance with the expected results obtained from analysis.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제32회 KOSCO SYMPOSIUM 논문집
• /
• pp.137-143
• /
• 2006

The effect of electric fields on flame speed has been investigated experimentally by observing propagating premixed flames in a tube for methane/air mixtures. The flame speeds were measured in both the normal and micro gravity conditions to substantiate the measurements. The results show that the flame speeds were enhanced by both the AC and DC electric fields, as the flame approached to the high voltage electrode located on the one end of the tube. The enhancement of flame speed was proportional to the square root of the electric field intensity, defined as the voltage applied divided by the distance of flame from the high voltage electrode, when the electric field intensity is sufficiently large. When the electric field intensity was low, there existed critical intensities, below which the electric fields did not influence the flame speed. This critical electric field intensity correlated well with the flame speed.

• 한국해양공학회지
• /
• 제13권2호통권32호
• /
• pp.66-73
• /
• 1999

This paper presents the experimental examinations and statistical quantitative analysis of the correlation between the cumulative counts of acoustic emission(AE) during plastic deformation periods of the welding and the tensile strength and other properties of the tube-to-tube welded joints of O.D. 30mm (I.D 18mm) nozzle steel. This is a new approach which attempts finally to develop real-time quality monitoring system for friction welding. And this study results in practical possiblility of real-time quality control more than 100% joint efficiency showing good weld no micro structural defects.

• 한국방사선학회논문지
• /
• 제17권6호
• /
• pp.859-863
• /
• 2023

본 연구에서는 엑스선 증감지와 광센서, 마이크로컨트롤러(MCU)를 이용하여 휴대와 이동이 용이한 교육용 방사선검출기를 제안하였다. 광센서와 증감지로 이루어진 검출부와 마이크로컨트롤부로 간단하게 구성되어 제작이 쉽고 소형화 및 휴대형으로 적합하게 제작되었다. 검출기의 성능 확인을 위해 전압을 50에서 100 kVp까지 변경하며 검출시스템과 흡수선량계를 이용하여 방사선을 측정하였다. 관전류량은 100 mAs, SDD는 100 cm로 고정하였고 각 관전압에서 10회 반복 측정하였다. 측정값을 이용하여 검출기의 응답과 선형성을 확인하였다. 검출기와 흡수선량계의 측정결과 비교에서 높은 상관성(r:0.998, p<.001)을 보임을 확인하였다. 이러한 결과를 통하여 본 연구에서 제안된 증감지와 마이크로컨트롤러 기반의 검출기의 사용가능성을 확인할 수 있었으며, 휴대형 방사선검출시스템이 소형, 저가형, 휴대형 시스템으로 교육용으로 적용이 가능할 것으로 판단되었다.