• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1035-1040
• /
• 2011

본 논문은 세라믹과 금속파우더를 이용한 복합소재를 플라즈마 용사 방식으로 개발한 결과를 수록하였다. 사용된 세라믹 파우더는 $Al_2O_3+40TiO_2$ 이고 입자 크기는 $20{\mu}m$, $Al_2O_398+$파우더의 입자 크기는 $45{\mu}m$를 사용하였다. $20{\mu}m$, $30{\mu}m$ 및 $50{\mu}m$ 금속필터 입자는 SIKA-R 20IS, 30IS 및 50IS(소결금속필터)을 사용 했으며, $75{\mu}m$ 금속필터 입자는 5 겹 소결메쉬 필터를 사용��다. 용사 공정으로 가공된 복합 필터는 세라믹 파우더의 종류, 크기 및 코팅 두께에 따라 성능의 차이를 보였으나, 전반적으로 필터링 가능 능력은 향상되었다.

• 대한토목학회논문집
• /
• 제41권3호
• /
• pp.237-246
• /
• 2021

기후변화로 극한강우에 의해 발생하는 얕은 비탈면 붕괴와 침식으로 토석류 유발이 잦아지고 있다. 앵커나 네일링 공법으로 보강하기 보다는 원지반을 이용하여 식생이 되는 비탈면 보강이 경제적이면서 친환경적인 공법으로 연구되고 있다. 본 연구에서는 충분한 식생이 가능하도록 부엽토와 한약재 찌꺼기를 활용하여 토양개량제를 개발하였다. 그리고 표면침식을 방지하기 위해 첨가제로 마이크로 시멘트와 반수석고 등을 사용하여 전단강도를 증가시켰다. 이러한 주재료와 첨가제 결정은 실내시험을 통하여 강우로 인한 지반 표층의 침식 진행을 확인하여 전단강도의 증가를 확인할 수 있었다. 원지반을 활용하는 토양개량제의 보강은 식생이 가능하고 침식에 대해 저항력이 크게 증가한다. 이러한 보강은 사면 불안정성의 주요 원인인 인장균열 발생을 방지하고 침식에 의한 토석류 유발을 막을 수 있기 때문에 다른 공법들보다 장마철 폭우에 대한 대처방안으로 효율적인 방법이라고 판단된다.

• 대한치과보철학회지
• /
• 제43권1호
• /
• pp.52-60
• /
• 2005

Purpose. The intent of this study was to evaluate the effects of curing conditions on self-curing denture base resins to find out proper condition in self-curing resin polymerization. Materials and methods, In this study, 3 commercial self-curing denture base resins are used Vertex SC, Tokuso Rebase and Jet Denture Repair Acrylic. After mixing the self curing resin, it was placed in a stainless steel mold(3$\times$6$\times$60mm). The mold containing the resin was placed under the following conditions: in air at 23$^{\circ}C$; or in water at 23$^{\circ}C$; or in water at 23$^{\circ}C$ under pressure(20psi); or in water at 37$^{\circ}C$ under pressure(20psi) or in water at 50$^{\circ}C$ under pressure(20psi) , or in water at 65$^{\circ}C$ under pressure(20psi), respectively. Also heat-curing denture base resin is polymerized according to manufactures' instructions as control. Fracture toughness was measured by a single edge notched beam(SENB) method. Notch about 3mm deep was carved at the center of the long axis of the specimen using a dental diamond disk driven by a dental micro engine. The flexural test was carried out at a crosshead speed 0.5mm/min and fracture surface were observed under measuring microscope. Results and conclusion . The results obtained were summarized as follows : 1. The fracture toughness value of self-curing denture base resins were relatively lower than that of heat-curing denture base resin. 2. In Vertex SC and Jet Denture Repair Acrylic, higher fracture toughness value was observed in the curing environment with pressure but in Tokuso Rebase, low fracture toughness value was observed but there was no statistical difference. 3. Higher fracture toughness value was observed in the curing environment with water than air but there was no statistical difference. 4. Raising the temperature in water showed the increase of fracture toughness.

• 한국자동차공학회논문집
• /
• 제20권4호
• /
• pp.46-51
• /
• 2012

Injection pressure, an important factor in filling process, should be minimized to enhance injection molding quality. Injection pressure can be controlled by valve gate open timing. In this work, we decided the valve gate open timing to minimize the injection pressure. To solve this design problem, we integrated MAPS-3D (Mold Analysis and Plastic Solution-3Dimension), a commercial injection molding CAE tool, to PIAnO (Process Integration, Automation and Optimization), a commercial PIDO (Process Integration, and Design Optimization) tool using the file parsing method. In order to reduce computational cost, we performed an approximate optimization using meta-models that replaced expensive computer simulations. At first, we carried out DOE (Design of Experiments) using OLHD (Optimal Latin Hypercube Design) available in PIAnO. Then, we built Kriging models using the simulation results at the sampling points. Finally, we used micro GA (Genetic Algorithm) available in PIAnO. Using the proposed design approach, the injection pressure has been reduced by 13.7% compared to the initial one. This design result clearly shows the validity of the proposed design approach.

• KIEAE Journal
• /
• 제10권5호
• /
• pp.115-121
• /
• 2010

Lime was the solidifier mostly used at the fields of construction and civil works in the past. however, the development of Portland cement remarkably reduced the use of it. Recently as the concernment on circumstances gets higher, lime wined attention again as an eco-friendly material and was used at earth-using construction. This study examined the physical and chemical capacity of lime complexes with lime capacity improved, and performed fundamental study on the way to concretize by mixing it with earth. As a result, lime complex pressure strength was lower than cement pressure strength but it showed the possibility that its strength was improved by W/B control. The measurement of XRD after paste formation confirmed a compound generated by the reaction of Ca2+ion and Si, Al, and Fe from pozzolan reaction. A earth wall experiment by using lime complexes and earth showed that the higher, WB or the lower the quantity of unit combined materials, the lower the pressure strength was. The maximum pressure strength was maximum 11MPa when the quantity of unit combined materials was 450. It is because the composed earth particles had a high content of micro powder less than silt, so a lot of combination are demanded to secure fluidity. As a result of peptization experiment, after hardening, the material was not dissolved, which informed of the possibility of use as an outer subsidiary material. If the material is hardened by mold formation method, natural hardening crack appears. Cast expresses smart surface quality and enables to design for multiple purpose. The result shows the possibility of construction of low-story structures by using earth wall made of lime complexes and earth.

• 한국산학기술학회논문지
• /
• 제12권11호
• /
• pp.4924-4931
• /
• 2011

본 연구는 유산균을 함유한 녹즙제품의 HACCP(Hazard Analysis Critical Control Point)시스템에 의한 제조공정도 작성과 공정별 원료 농산물과 제조 시설에 대한 일반 세균수와 병원성 미생물을 평가하기 위한 목적으로 수행하였다. 공정별 원료농산물의 원재료보관공정 단계의 4가지 시료에서 일반세균이 검출되었으며, 용수(water)는 8.67~14.67 CFU/$m{\ell}$ 검출되었다. 하지만 자외선살균공정 이후, 모든 시료는 법적기준치인 $10^5\;CFU/m{\ell}$이하로 검출되었다. 식중독균인 E. coil, E. coli O157:H7, B. cereus, L. monocytogenes, Salmonella spp, Staph. aureus 실험결과, 보관공정에서 E.coli는 자외선 살균 전단계 공정까지 검출되었으며, B. cereus는 1차세척까지 일부 검출되었다. 모든 세균 및 진균류는 주원료에서 많이 검출되고 있어 주원료의 초기 균수를 최소화하는 선행관리방법을 수립할 필요가 있으며, 세균수와 황색포도상구균 등의 교차 오염방지를 위한 제조설비 등의 효과적인 세척 소독방법을 수립할 필요가 있다고 사료된다. 상기 결과을 바탕으로 유산균을 함유한 녹즙류의 일반세균 및 식중독균을 감소 또는 제거할 수 있는 중요한 공정으로 UV살균공정이 CCP로 관리되어야 한다. 따라서 자외선살균공정의 관리기준 및 이탈시 조치방법, 검증방법, 교육 훈련과 기록관리 등 철저한 HACCP 계획이 필요하다고 사료된다.

• Restorative Dentistry and Endodontics
• /
• 제22권1호
• /
• pp.254-266
• /
• 1997

This study was to know the usefulness of argon laser for composite resin, to prove the polymerized effect of heat treatment of composite resin inlay and to get the curing method for optimal physical properties of composite resin inlay. In this study we used four light curing units and one heat curing unit: Visilux $II^{TM}$, a visible light gun: $SPECTRUM^{TM}$, an argon laser: Unilux AC$^{(R)}$ and Astorn XL$^{(R)}$, visible light curing unit: CRC-$100^{TM}$ for heat treatment. Compared to a control group, we divided the experemental groups into five as follows: Control group: Light curing(Visilux $II^{TM}$) Experimental group 1 : Light curing(Visilux $II^{TM}$) + Light curing(Unilux AC$^{(R)}$) Experimental group 2: Light curing(Visilux $II^{TM}$) + Light curing(Astron XL$^{(R)}$) + Heat treatment(CRC-$100^{TM}$) Experimental group 3 : Laser curing($SPECTRUM^{TM}$) Experimental group 4 : Laser curing($SPECTRUM^{TM}$) + Light curing(Unilux AC$^{(R)}$) Experimental group 5 : Laser curing($SPECTRUM^{TM}$) + Light curing(Astron XL$^{(R)}$) + Heat treatment (CRC-$100^{TM}$) According to the above classification, we made samples through the curing of Clearfil CR Inlay$^{(R)}$, which is a composite resin for inlay, in a separable cylindrical metal mold and polycarbonate plate. And then, we measured and compared the value of compressive strength, diametral tensile strength and the surface micro hardness of each sample. The results were as follows : 1. Among the experimental groups, group 5 showed the highest value of compressive strength, $157.50{\pm}10.24$ kgf and control group showed the lowest value of compressive strength, $103.93{\pm}21.93$ kgf. Control group showed significant difference with the experimental groups(p<0.001). Group 2 which was treated by the heat showed higher compressive strength than that of group 1 which was not, and there was significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was significant difference group 4 and group 5(p<0.001). 2. Among the experimental groups, group 5 showed the highest value of diametral tensile strength, $95.84{\pm}1.97$ kgf and control group showed the lowest value of diametral tensile strength, $81.80{\pm}2.17$ kgf. Control group which was cured by visible light showed higher diametral tensile strength than group 3 which was cured Argon Laser. Group 2 which was treated by heat showed higher compressive strength than that of group 1 which was not, and there was significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was a significant difference group 4 and group 5(p<0.001). 3. Among the experimental groups, group 5 showed the highest value of microhardness of top surface, $148.42{\pm}9.57$ kgf and control group showed the lowest value of microhardness, $111.43{\pm}7.63$ kgf. In the case of bottom surface, group 5 showed the highest value of $146.19{\pm}7.62$ kgf, and control group showed the lowest, $104.03{\pm}11.05$ kgf. Group 3 which was cured by Argon Laser showed higher diametral tensile strength than control group which was cured only with a visible light gun. Group 2 which was treated by heat showed higher compressive strength than that of group 1 which was not, and there was a significant difference between group 1 and group 2(p<0.001). Group 5 which was treated by heat showed higher compressive strength than group 4 which was not, and there was a significant difference group 4 and group 5(p<0.001). 4. According to the above results, we took a conclusion that argon laser can be used as a useful unit for curing the composite resin and heat treatment can improve the physical properties of the composite resin inlay.