• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.861-864
• /
• 1997

Singulation is a process that cutting for separating a chip individually after finishing packaging process(micro BGA etc.). For shortening the process of singulation, we proposed the singulation using multi-blade. This paper introduced a method of multi-blade singulation and investigated a result of application and problems. The efficiency of singulation process was improved five times better than the single-blade by the singulation using Multi-blade.

• 한국유체기계학회 논문집
• /
• 제17권4호
• /
• pp.19-29
• /
• 2014

In addition to the development of micro hydro turbine, the challenge in micro hydro turbine design as sustainable hydro devices is focused on the optimization of turbine runner blade which have decisive effect on the turbine performance to reach higher efficiency. A multi-objective optimization method to optimize the performance of runner blade of propeller turbine for micro turbine has been studied. For the initial design of planar blade cascade, singularity distribution method and the combination of the Bezier curve parametric technology is used. A non-dominated sorting genetic algorithm II(NSGA II) is developed based on the multi-objective optimization design method. The comparision with model test show that the blade charachteristics is optimized by NSGA-II has a good efficiency and load distribution. From model test and scale up calculation, the maximum prototype efficiency of the runner blade reaches as high as 90.87%.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.893-899
• /
• 2014

X-band antenna has been widely used to effectively transmit the high resolution image data from the observation satellite to the ground station. To achieve above mission, X-band antenna is mainly composed of the 2-axis gimbal system using stepping motors and gears. However, the micro-vibration induced by the stepping motor actuation and the imperfect gear teeth alignment during this on-orbit operation is the main source of image quality degradation. In this paper, X-band antenna combined with a blade gear for micro-vibration isolation was suggested and investigated. The structural safety of the blade gear with low rotational stiffness was confirmed by structure analysis based on the derived torque budget. The isolation performance of the X-band antenna with the blade gear was verified through micro-vibration measurement test using the dedicated micro-vibration measurement device proposed in this study.

• 한국소음진동공학회논문집
• /
• 제25권5호
• /
• pp.313-320
• /
• 2015

A 2-axis gimbal-type X-band antenna has been widely used to effectively transmit the high resolution image data from the observation satellite to the desired ground station. However, a discontinuous stepper motor activation for rotating the pointing mechanism in azimuth and elevation directions induces undesirable micro-vibration disturbances which can result in the image quality degradation of a high-resolution observation satellite. To enhance the image quality of the observation satellite, attenuating the micro-vibration induced by an activation of the stepper motor for rotational movements of the antenna is important task. In this study, we proposed a low-rotational-stiffness blade gear applied to the output shaft of the stepper motor to obtain the micro-vibration isolation performance. The design of the blade gear was performed through the structure analysis such that this gear is satisfied with the margin of safety rule under the derived torque budget. In addition, the micro-vibration isolation performance of the blade gear was verified through the micro-vibration measurement test using the dedicated micro-vibration measurement device proposed in this study.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2009년도 추계학술대회 논문집
• /
• pp.448-448
• /
• 2009

A new blade has been developed to apply to Doosan 3MW offshore wind turbine named as WinDS3000TM. The 3MW blade has been designed by the concept of slim external shape and optimized structure. High-performance glass fiber reinforced epoxy composites were used as the main material of the blade. The blade was manufactured using vacuum infusion process in order to increase the fiber volume fraction and to reduce micro-porosities. The blade has successfully passed the full-scale blade static test for certification. During the test, micro-failure signal and strain change of the blade were measured using acoustic emission sensors and strain gages. The blade has robust structure and weighs lighter compared to conventional blade since the new blade was designed by optimization process. The 3MW blade will be commercially applied to WinDS$3000^{TM}$ in 2010.

• 한국추진공학회지
• /
• 제11권4호
• /
• pp.10-18
• /
• 2007

본 연구에 채택된 마이크로터빈은 축류형 터빈으로 2단으로 구성되어져 있으며 로터 유로에서의 평균반경이 8.4 mm이다. 이러한 소형 터빈은 마이크로 동력시스템의 드라이브로 사용되어질 수 있으며 무부하 상태에서 100,000 RPM의 회전속도에 도달한다. 하지만 낮은 부분분사에서 작동하므로 동익과 정익의 익형각에 따라 성능의 변화가 발생되어진다. 따라서 노즐, 정익, 동익의 익형각을 변경하면서 비출력과 총 비토오크를 측정하여 각각의 성능을 분석하였다. 성능실험의 결과에 의하면 동익 익형각의 변화에 따라 총 비토오크가 15%까지 변경되어졌으며 최적의 입사각은 $10.3^{\circ}$ 정도였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2010년도 추계학술대회 논문집
• /
• pp.145-146
• /
• 2010

• 한국표면공학회지
• /
• 제41권6호
• /
• pp.335-340
• /
• 2008

Cutting performance and wear behavior were studied with the diamond micro-blade of Cu/Sn bond materials containing various amount of lubricant materials such as graphite and $MoS_2$. Measurement of instantaneous electric power consumption for cutting glass workpiece at the constant velocity was conducted and proposed as a method to assess cutting efficiency. The energy consumption of micro-blade for glass cutting decreased with the content of graphite and $MoS_2$ while wear amount of blade in volume increased with the amount of lubricant addition during the dicing test. It is because that hardness, flexural strength, and fracture toughness ($K_{IC}$) reduced with the amount of lubricant addition. Blades with $MoS_2$ additive showed higher mechanical properties than those with graphite additives when the same amount of the lubricant additive in wt.% was added. Due to the lower density of graphite than $MoS_2$, higher volume fraction of graphite could result in stronger effect on lowering electric power consumption by reducing the friction between blade and work piece however increasing wear rate due to the reduction in strength and fracture toughness. Adhesive wearing mode of micro blade could be remarkably improved by the addition of graphite as well as $MoS_2$.

• Composites Research
• /
• 제20권5호
• /
• pp.49-55
• /
• 2007

반도체 쿼츠 웨이퍼 다이싱용 블레이드는 마이크로/나노 디바이스와 부품을 제조하기 위해 고정밀도의 가공성을 요구한다. 따라서 균일한 마이크로/나노 선폭의 가공을 위해서는 블레이드의 제작 단계에서 균일한 두께와 밀도를 유지하는 것이 중요하다. 기존의 실리콘웨이퍼 가공을 위해서는 금속의 블레이드가 사용되고 있지만 쿼츠 웨이퍼 가공을 위해서는 고분자 복합재가 사용된다. 이러한 복합재는 가공성, 전기전도성, 그리고 적절한 강도와 연성 및 마모저항성이 있어야 한다. 그러나 기존의 건식성형 공정으로는 균일성을 유지하기 위해 많은 공정과 비용이 소비되고 있다. 본 연구에서는 도전성 나노 세라믹스 분말, 연마재 세라믹스 분말에 열경화성 수지, 전도성 고분자를 혼합한 복합재 분말을 습식성형 공정에 의해 제조, 평가하는 연구를 수행하였다. 먼저 복합재 분말을 액상과 혼합하여 블레이드를 제작하였으며, 액상의 종류, 액상 건조공정의 영향을 고찰하였다. 평가는 마이크로미터 측정기와 현미경을 이용하여 두께를 측정하였다. 두께편차와 기공률, 밀도, 경도, 등의 특성을 비교, 평가하였다. 그 결과 습식성형에 의해 블레이드의 두께편차를 감소시킬 수 있었으며, 경도 등의 특성을 향상시킬 수 있었다.

• 한국식품과학회지
• /
• 제20권4호
• /
• pp.504-510
• /
• 1988

여러 종류의 제분기를 사용하여 건식 (blade hammer, test, micro mill) 및 습식과 건식병용(roller & micro mill)으로 제조한 쌀가루의 이화학적 특성을 조사 하였다. 쌀가루의 입자는 blade, hammer, test, micro mill및 roller & micro mill의 순으로 점차 미세하였으며, 입자가 미세하여 짐에 따라 색의 밝기를 나타내는 L값은 증가한 반면 a값(적색도) 및 b값(황색도)은 감소하였다. 쌀가루의 표면구조를 주사전자현미경으로 관찰한 결과 입자가 미세하여 짐에 따라 개개의 전분입자의 관찰이 용이하였다. 전분의 손상도. 말토오스 값 및 열수가용성 아밀로오스의 함량은 blade mill이 가장 낮았고 test mill이 가장 높았다. 아밀로그램상 호화개시 온도와 최고점토는 입자가 미세하여 짐에 따라 점차 낮아졌으며, 건식제분한 쌀가루 현탁액의 최고점도는 잔존하는 ${\alpha}$-아밀라아제에 의해 감소경향을 나타내었으나 습식과 건식을 병용한 쌀가루에서는 최고점도의 변화가 없었다. 건식제분의 경우 유리아미노산의 함량은 전분의 손상도가 증가함에 따라 다소 증가하였다. 쌀가루로부터 추출한 냉수가용 ${\alpha}-D-glucan$의 blue value는 $0.023{\sim}0.029$, 극대흡수파장은 $518{\sim}522nm$정도의 범위를 나타내어 이들 물질은 아밀로펙틴에 유사한 성질을 지니고 있었다.