• 한국의학물리학회지:의학물리
• /
• 제5권2호
• /
• pp.35-43
• /
• 1994

전자파가 일상생활에서 생체에 많은 영향을 미치는 것으로 알려져 있으나 실제로 그 영향을 정성, 정량적으로 규명하는 것은 용이하지 않다. 본 연구에서는 생체의 전기적 신호를 이용하여 2.45GHz의 전자파에 노출시킨 토끼의 두부에 대한 영향을 측정하는 방법을 검토하였다. 연구결과, 두부모델의 손상정도는 뇌전위의 연속적인 FFT 신호처리에서 뇌활성도 저하를 관찰할 수 있었으며, 특정 주파수와 강도(최소허용전력과 치사전력)에 대한 기준 설정에 필요한 요소를 제시할 수 있었다.

• 동력기계공학회지
• /
• 제17권2호
• /
• pp.38-45
• /
• 2013

In this study, for carrying out the spray and combustion experiment using a Common Rail Direct Injection(CRDI) system, the controller was fabricated to drive a high speed camera, a injector and a laser beam sequentially at a low cost. CB280 module of one-chip micro processer was used for the controller. In order to confirm responsibility and utility of the controller, the current drive performance, the spray behavior and the injection rate were tested and analyzed under various experimental conditions. As this research results, we found that the fabricated controller was able to control the devices for the spray experiment precisely with the input value in program and it had the dynamic load responsibility and repetition. Also, we found that the injection rates of our experimental results were higher than those of others at the same injection pressure and the controller connected with the laser system and the data acquisition system had validity for carrying out the spray visualization experiment.

• Journal of Power Electronics
• /
• 제10권2호
• /
• pp.187-193
• /
• 2010

This paper proposes a cooling system using thermoelectric elements for improving the output of building integrated photovoltaic (BIPV) modules. The temperature characteristics that improve the output of a BIPV system have rarely been studied up to now but some researchers have proposed a method using a ventilator. The efficiency of a ventilator depends mainly on the weather such as wind, irradiation etc. Because this cooling system is so sensitive to the velocity of the wind, it is unable to operate in the nominal operating cell temperature (NOCT) or the standard test condition (STC) which allow it to generate the maximum output. This paper proposes a cooling system using thermoelectric elements to solve such problems. The temperature control of thermoelectric elements can be controlled independently in an outdoor environment because it is performed by a micro-controller. In addition, it can be operated around the NOCT or the STC through an algorithm for temperature control. Therefore, the output of the system is increased and the efficiency is raised. This paper proves the validity of the proposed method by comparing the data obtained through experiments on the cooling systems of BIPV modules using a ventilator and thermoelectric elements.

• 반도체디스플레이기술학회지
• /
• 제21권2호
• /
• pp.101-106
• /
• 2022

In this paper, WBG semiconductor such as SiC and GaN were applied as power switches for LCL circuit that can be applied to satellite power systems and the test results of the LCL circuit are reported. P-channel MOSFET and N-channel MOSFET, which were generally used in the conventional LCL circuit, were applied together to expand the utility of the test results. The design and stability evaluation were performed using a Micro Cap circuit simulation program. For the test circuit, a module using each switch was manufactured, and a total of 5 modules were manufactured and the steady state and transient state characteristics were compared. From the experimental results, the LCL circuit for power supply of the satellite power system constructed in this paper satisfied the constant current and constant voltage conditions under various operating conditions. The P-channel MOSFET showed the lowest efficiency characteristics, and the three N-channel switches of Si, SiC and GaN showed relatively high efficiency characteristics of up to 99.05% or more. In conclusion, it was verified that the on-resistor of the switch had a direct effect on the efficiency and loss characteristics.

• 한국인터넷방송통신학회논문지
• /
• 제11권6호
• /
• pp.247-253
• /
• 2011

본 논문에서는 감성조명의 소모전력 절감을 위한 거리 측정 센서 기반 자동 조광 제어 시스템을 제안하고 구현한다. 지속적인 색상변화를 표현해야 하는 감성 조명에서의 소비 전력 절감을 위하여 초음파 센서를 이용한 사용자와의 지속적인 거리 측정 및 이를 통한 PWM Dimming 제어를 수행한다. 조명장치는 마이크로 컨트롤러, LED Driver, 초음파 센서, 통신모듈 등으로 구성되며, 초음파 센서를 통해 측정된 거리 정보를 PWM 신호에 적용하여 실시간 밝기 제어를 수행한다. 기존 조명에서의 에너지 절감 기법을 감성조명에 적용하여 사용자 부재 시 불필요한 전력 소모를 최소화하는 능동형 조명 시스템을 구현한다.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제55권12호
• /
• pp.511-517
• /
• 2006

The key issues in high power, high energy applications such as electromagnetic launchers include safety, reliability, flexibility, efficiency, compactness, and cost. To explore some of the issues, a control scheme for a large current wave-forming was designed, built and experimentally verified using a 2.4MJ pulse power system (PPS). The PPS was made up of eight capacitors bank unit, each containing six capacitors connected in parallel. Therefore there were 48 capacitors in total, with ratings of 22kV and 50kJ each. Each unit is charged through a charging switch that is operated by air pressure. For discharging each unit has a triggered vacuum switch (TVS) with ratings of 200kA and 250kV. Hence, flexibility of a large current wave-forming can be obtained by controlling the charging voltage and the discharging times. The whole control system includes a personal computer(PC), RS232 and RS485 pseudo converter, electric/optical signal converters and eight 80C196KC micro-controller based capacitor-bank module(CBM) controllers. Hence, the PC based controller can set the capacitor charging voltages and the TVS trigger timings of each CBM controller for the current wave-forming. It also monitors and records the system status data. We illustrated that our control scheme was able to generate the large current pulse flexibly and safely by experiments. The our control scheme minimize the use of optical cables without reducing EMI noise immunity and reliability, this is resulting in cost reduction. Also, the reliability was increased by isolating ground doubly, it reduced drastically the interference of the large voltage pulse induced by the large current pulse. This paper contains the complete control scheme and details of each subsystem unit.

• 한국세라믹학회지
• /
• 제51권6호
• /
• pp.549-553
• /
• 2014

$CoSb_3$-based skutterudite compounds are candidate materials for thermoelectric power generation in the mid-temperature range (600 - 900 K) because their thermoelectric properties can be enhanced by doping and filling. The joining property of thermoelectric module electrodes containing thermoelectric materials is of great importance because it can dominate the efficiency of the thermoelectric module. This study examined the properties of $CoSb_3$/Al/Ti/CuMo joined by the spark plasma sintering technique. Titanium thin foil was used to prevent the diffusion of copper into $CoSb_3$ and Aluminum thin foil was used to improve the adhesion between $CoSb_3$ and Ti. The insertion of an Aluminum interlayer between the Ti and $CoSb_3$ was effective for joining $CoSb_3$ to Ti by forming an intermediate layer at the Al-$CoSb_3$ boundary without any micro cracks. Specifically, the adhesion strength of the Ti/Al/$CoSb_3$ joining interface showed a remarkable improvement compared with our previous results, without deterioration of electrical property in the interface.

• 대한전자공학회논문지SD
• /
• 제40권4호
• /
• pp.85-94
• /
• 2003

비동기 설계 기법은 시스템 클럭을 사용하지 않고, 동작이 필요한 모듈만 활성화시켜 전력 및 성능면에서 동기식 설계 기법에 비해 높은 성능을 갖는다. 본 논문은 임베디드 컨트롤러인 Intel 80csl과 완전한 명령어 호환성을 갖고, 비동기식 파이프라인 구조로 최적화된 A8051 아키텍쳐를 제안한다. 다양한 어드레싱 모드와 명령어를 제공하는 CISC 명령어 수행 스킴은 동기식 파이프라인 구조에 적합하지 않고 많은 오버헤드를 유발한다. 본 논문에서는 명령어 실행 사이클을 비동기식 파이프라인 수행에 적합하도록 명령어별로 그룹화하고, 동기화 및 다중 실행 사이클로 인한 오버헤드로 발생된 버블을 제거함으로서 최적화하였다. 또한 적합한 분기 처리 기법 및 가변적인 명령어 길이의 처리 방법을 제시함으로서 명령어 수행시 필요한 상태 수를 최소화하고, 명령어 수행의 병렬성을 증가시켰다. 제안된 A8051 아키텍쳐는 Verilog HDL로 설계하여 0.,35㎛ CMOS 공정 표준 셀 라이브러리로 합성하였다. 실험 결과로 A8051은 36㎒ 클럭을 사용하는 인텔 80C51과 다른 비동기 80C51에 비해 약 24배의 성능 향상을 얻었다.

• ETRI Journal
• /
• 제38권4호
• /
• pp.665-674
• /
• 2016

We designed and fabricated a semiconductor optical amplifier-integrated dual-mode laser (SOA-DML) as a compact and widely tunable continuous-wave terahertz (CW THz) beat source, and a pin-photodiode (pin-PD) integrated with a log-periodic planar antenna as a CW THz emitter. The SOA-DML chip consists of two distributed feedback lasers, a phase section for a tunable beat source, an amplifier, and a tapered spot-size converter for high output power and fiber-coupling efficiency. The SOA-DML module exhibits an output power of more than 15 dBm and clear four-wave mixing throughout the entire tuning range. Using integrated micro-heaters, we were able to tune the optical beat frequency from 380 GHz to 1,120 GHz. In addition, the effect of benzocyclobutene polymer in the antenna design of a pin-PD was considered. Furthermore, a dual active photodiode (PD) for high output power was designed, resulting in a 1.7-fold increase in efficiency compared with a single active PD at 220 GHz. Finally, herein we successfully show the feasibility of the CW THz system by demonstrating THz frequency-domain spectroscopy of an ${\alpha}$-lactose pellet using the modularized SOA-DML and a PD emitter.

• 한국정밀공학회지
• /
• 제30권3호
• /
• pp.340-348
• /
• 2013

In Projection Stereolithography Apparatus (PSLA), Digital Micromirror Device (DMD) and Liquid Crystal Display (LCD) are used as a beam pattern generator. The DMD shows high resolution, but it is mostly applied in micro stereolithography due to high cost and fabricable area. In LCD, the size of pattern beam is freely controlled due to various panel sizes. The LCD, however, has some limitations such as short life time by the high power light source, non-uniform light intensity of pattern beam and low transmittance of UV-light. To solve these problems in LCD-based PSLA, a Scanbeam-SLA with LCD of 19 inches and visible LED-array is developed. In this system, the light module works like a scanner for uniform illumination. The system configuration, working principle and fabrication examples are addressed in this study.