• 한국표면공학회지
• /
• 제47권1호
• /
• pp.13-19
• /
• 2014

The various surface treated conditions of Fe-3.0%Ni-0.7%Cr-1.4%Mn-X steel such as as-received, ion nitriding, DLC coated, DLC coated after nitriding for 3 hrs and 6 hrs were investigated to evaluate the beneficial effect for plastic mold steel. Micro Vickers hardness tester was used to estimate nitriding depth from the hardness profile and to measure hardness on the surface. Elastic modulus and residual stress were measured by a nanoindentator. Scratch test and SP (small ball punch test) were utilized to assess the adhesive strength of DLC coating. The depth of nitriding layer was measured as $50{\mu}m$ for the condition of 3 hrs nitriding and $90{\mu}m$ for that of 6 hrs nitriding. Hardness, elastic modulus, residual stress of DLC coating were 20.37 GPa, 162.78 GPa and -1456 MPa respectively. Residual stress on the surface of DLC coating after nitriding could increase to -3914 MPa by introducing nitriding before DLC coating. During the 'Ball-On-Disc' test ${\gamma}^{\prime}$ particles pulled out from the surface of nitrized layer tend to enhance abrasive wear mode since the fraction of ${\gamma}^{\prime}$ (Fe4N) in ion-nitrized layer is known to increases with nitriding time. Thus the specific wear rate of the nitriding layer increased. Comparing with nitriding the specific wear rate in work piece disc as well as ball decreased prominently in DLC coating due to the remarkable reduction in friction coefficient.

• Journal of Welding and Joining
• /
• 제17권1호
• /
• pp.124-132
• /
• 1999

Thermal fatigue strength of the solder joints is the most critical issue for TSOP(Thin Small Outline Package) because the leads of this package are extremely short and thermal deformation cannot be absorbed by the deflection of the lead. And the TSOP body can be subject to early fatigue failures in thermal cycle environments. This paper was discussed distribution of thermal stresses at near the joint between silicon chip and die pad and investigated their reliability of solder joints of TSOP with 42 alloy clad lead frame on printed circuit board through FEM and 3 different thermal cycling tests. It has been found that the stress concentration around the encapsulated edge structure for internal crack between the silicon chip and Cu alloy die pad. And using 42 alloy clad, The reliability of TSOP body was improved. In case of using 42 alloy clad die pad(t=0.03mm). $$\sigma$_{VMmax}$ is 69Mpa. It is showed that 15% improvement of the strength in the TSOP body in comparison with using Cu alloy die pad $($\sigma$_{VMmax}$=81MPa). In solder joint of TSOP, the maximum equivalent plastic strain and Von Mises stress concentrate on the heel of solder fillet and crack was initiated in it's region and propagated through the interface between lead and solder. Finally, the modified Manson-Coffin equation and relationship of the ratio of $N_{f}$ to nest(η) and cumulative fracture probability(f) with respect to the deviations of the 50% fracture probability life $(N_{f 50%})$ were achieved.

• 열처리공학회지
• /
• 제27권6호
• /
• pp.281-287
• /
• 2014

Microstructural and mechanical characteristics of Al-6Si-2Cu alloy for engine mount bracket prepared by gravity casting (as-cast) and die-casting (as-diecast) process have been investigated. For the microstructural characterization, the inductively coupled plasma mass spectrometry (ICP-MS), optical microscope (OM), scanning electron microscope (SEM) and electron probe microanalysis (EPMA) analyses are conducted. For the intermetallic phases, the X-ray diffraction (XRD) and energy dispersive spectroscopy (EDS) are also conducted with quantitative and qualitative analysis. Micro Vickers hardness and static tensile test are achieved in order to measure mechanical properties of alloys. Secondary dendrite arm spacing (SDAS) of as-cast and as-diecast show 37um and 18um, respectively. A large amount of coarsen eutectic Si, $Al_2Cu$ intermetallic phase and Fe-rich phases are identified in the Al-6Si-2Cu alloy. Mechanical properties of gravity casting alloy are much higher than those of die-casting alloy. Especially, yield strength and elongation of gravity casting alloy show 2 times higher than die-casting alloy. After shot peening, shot peening refined the surface grains and Si particles of the alloys by plastic deformation. The surface hardness value shows that shot peening alloy has higher value than unpeening alloy.

• 대한수의학회지
• /
• 제31권3호
• /
• pp.259-264
• /
• 1991

The proteins of the race horse erythrocyte membrane were analysed by polyacrylamide gel electrophoresis in sodium dodecyl sulfate(SDS-PAGE), and their relations to the fast erythrocyte sedimentation rate(ESR) of the race horse were investigated. The erythrocyte sedimentation rate of race horse were very fast compared with the human one(33 times <$90^{\circ}-plastic-ESR/30m$> and 25 times <$90^{\circ}-micro-ESR/30m$> as fast as the human one) are reported previously. Although the general protein profiles of the race horse erythrocyte membranes were almost similar to that of human, band 3 content was showing higher in race horse (34.7%) than in human (25.3%). The glycoprotein profiles of the race horse erythrocyte membranes revealed by periodic acid Schiff's(PAS) stain showed a marked difference from that of human. The PAS-1(glycophorin) and PAS-2(sialoglycoprotein) present in human erythrocyte memo brane were almost absent from the Holstein and race horse erythrocyte membranes, but PAS-2 was more in only race horse from that of human. Instead, the bovine erythrocyte membranes showed a strong PAS-B near the origin of the electrophorograms and the race horse erythrocyte membranes showed a strong PAS-negative band near the end of the electrophorograms, which is named as PAS-E in this study. These results suggest that the fast sedimentation rate of race horse erythrocyte is due in part to the presence of more band 3 protein fraction and PAS-E glycoproteins in the race horse erythrocytes.

• Elastomers and Composites
• /
• 제44권4호
• /
• pp.384-390
• /
• 2009

롤-롤(Roll to roll) 성형은 공정이 비교적 간단하고 생산 효율이 높은 중요한 금속 성형 공정이다. 이러한 이유로 롤-롤 성형 공정은 최근에 솔라셀 집전판, 디스플레이 격벽구조, 그리고 회로기판 성형 등 넓은 범위에서의 활용이 검토되고 있다. 본 연구에서는 솔라셀 집전판에 수십만 개의 홈을 성형하는 공정에 대해 유한요소해석을 수행하였다. 수백만 개 홈에 대한 성형을 해석하는 것은 컴퓨터 용량과 시간의 문제로 불가능하기 때문에 공정 설계를 가능하게 하는 최소의 문제 영역을 해석 결과를 바탕으로 설정하였다. 그리고, 홈의 형상과 온도에 따른 해석을 수행하여 그 결과를 분석함으로서 공정 설계의 방향성을 제시하였다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2008년도 춘계 학술발표회 제20권1호
• /
• pp.557-560
• /
• 2008

최근 선진 외국에서는 단섬유를 보강재로 사용함으로써 콘크리트의 역학적 성질을 증가시키고 콘크리트의 소성 및 건조수축으로 인한 균열을 저감시키고자 적극적으로 사용되어지고 있으며, 국내에서도 그 사용이 점차 증대되고 있는 실정이다. 그러나 섬유보강 콘크리트의 경우 많은 장점이 있지만, 섬유의 종류, 형태 및 혼입률에 따라 콘크리트의 공기량, 슬럼프, 분산성, 균열저감 및 역학적 성능 증진 효과에 큰 차이가 있으므로 그 용도에 따라 섬유 소재의 장점은 살리고, 단점은 보완하여 고기능성 복합재료로 발전시켜야 한다. 또한, 염해에 관한 콘크리트 구조물의 내구수명을 예측하기 위하여 콘크리트의 염소이온 확산계수는 매우 중요한 인자이며, 이는 콘크리트의 종류에 따라 많은 차이가 발생하므로 이에 따라 콘크리트 구조물의 내구수명이 크게 달라질 수 있다. 본 연구에서는 OPC를 사용한 보통강도 콘크리트 및 이에 나일론섬유 길이 13mm, 20mm를 각각 혼입한 3종류 콘크리트의 염소이온 침투 저항성을 평가하기 위하여 NT Build 492 시험법인 전위차를 이용한 전기화학적 촉진시험을 수행하였다. 시험 결과, 콘크리트의 확산계수는 3종류 콘크리트 모두 $2.02{\sim}2.11E-11m^2/sec$범위로서, 나일론섬유를 콘크리트에 보강했을 때 콘크리트의 염소이온 확산계수에는 큰 영향을 미치지 않는 것으로 확인되었다.

• Geomechanics and Engineering
• /
• 제20권3호
• /
• pp.207-220
• /
• 2020

Clay soils have a big potential to become contaminated with the oil derivatives because they cover a vast area of the earth. The oil derivatives diffusion in the soil lead to soil contamination and changes the physical and mechanical properties of the soil specially clay soils. Soil stabilization by using new material is very important for geotechnical engineers in order to improve the engineering properties of the soil. The main subjects of this research are a- to investigate the effect of the cement and epoxy resin mixtures on the stabilization and on the mechanical parameters as well as the microstructural properties of clay soils contaminated with gasoline and kerosene, b- study on the phenomenon of clay concrete development. Practical engineering indexes such as Unconfined Compressive Strength (UCS), elastic modulus, toughness, elastic and plastic strains are all obtained during the course of experiments and are used to determine the optimum amount of additives (cement and epoxy resin) to reach a practical stabilization method. Microstructural tests were also conducted on the specimens to study the changes in the nature and texture of the soil. Results obtained indicated that by adding epoxy resin to the contaminated soil specimens, the strength and deformational properties are increased from 100 to 1500 times as that of original soils. Further, the UCS of some stabilized specimens reached 40 MPa which exceeded the strength of normal concrete. It is interesting to note that, in contrast to the normal concrete, the strength and deformational properties of such stabilized specimens (including UCS, toughness and strain at failure) are simultaneously increased which further indicate on suitability and applicability of the current stabilization method. It was also observed that increasing cement additive to the soil has negligible effect on the contaminated soils stabilized by epoxy resin. In addition, the epoxy resin showed a very good and satisfactory workability for the weakest and the most sensitive soils contaminated with oil derivatives.

• 항공우주시스템공학회지
• /
• 제12권2호
• /
• pp.46-58
• /
• 2018

고해상도 관측위성의 대용량 영상 데이터 송신용인 2축 짐벌식 X-밴드 안테나는 궤도 임무수행 중 안테나 구동에 따라 미소진동을 유발하며, 이는 관측위성의 영상 품질을 저하시키는 요인 중 하나이기 때문에 반드시 절연되어야 할 대상이다. 본 논문에서는 상기 X-밴드 안테나의 방위각 구동에 따른 미소진동절연과 동시에 기존에 제안된 티타늄 블레이드 기어가 소성변형에 취약한 문제점을 보완하기 위해 초탄성 형상기억합금 (SMA)을 활용한 메쉬 와셔 기어를 제안하였다. 상기 SMA 메쉬 와셔 기어의 기본 특성을 파악하기 위해 SMA 메쉬 와셔 두께방향 정하중 시험과 SMA 메쉬 와셔 기어 수준의 회전방향정하중 시험을 실시하였다. 아울러 안테나 조립체 수준의 미소진동 측정시험을 통해 제안된 SMA 메쉬와셔 기어의 진동절연이 효과적임을 입증하였다.

• 천문학회보
• /
• 제37권2호
• /
• pp.120.1-120.1
• /
• 2012

The Lunar Reconnaissance Orbiter (LRO) launched on June 16, 2009 has six experiments including of the Cosmic Ray Telescope for the Effects of Radiation (CRaTER) onboard. The CRaTER instrument characterizes the radiation environment to be experienced by humans during future lunar missions. The CRaTER instrument measures the effects of ionizing energy loss in matter specifically in silicon solid-state detectors due to penetrating solar energetic protons (SEP) and galactic cosmic rays (GCRs) after interactions with tissue-equivalent plastic (TEP), a synthetic analog of human tissue. The CRaTER instrument houses a compact and highly precise microdosimeter. It measures dose rates below one micro-Rad/sec in silicon in lunar radiation environment. Forbush decrease (FD) event is the sudden decrease of GCR flux. We use the data of cosmic ray and dose rates observed by the CRaTER instrument. We also use the CME list of STEREO SECCHI inner, outer coronagraph and the interplanetary CME data of the ACE/MAG instrument.We examine the origins and the characteristics of the FD-like events in lunar radiation environment. We also compare these events with the FD events on the Earth. We find that whenever the FD events are recorded at ground Neutron Monitor stations, the FD-like events also occur on the lunar environments. The flux variation amplitude of FD-like events on the Moon is approximately two times larger than that of FD events on the Earth. We compare time profiles of GCR flux with of the dose rate of FD-like events in the lunar environment. We figure out that the distinct FD-like events correspond to dose rate events in the CRaTER on lunar environment during the event period.

• 한국산학기술학회논문지
• /
• 제16권9호
• /
• pp.5743-5747
• /
• 2015

본 연구에서는 가스아토마이저로 제조된 Fe계 벌크비정질 합금 분말을 이용하여 제작된 시험편에 레이저 육성용접을 하였고, 인장시험과 경도시험의 실시 및 미세조직을 관찰하여 육성용접 층의 파괴거동을 분석하였다. 인장시험 결과 육성용접층은 탄성변형 후 바로 파괴가 일어났고, 모재는 소성변형 후 파괴가 일어났다. 육성용접층과 모재의 실제 최대인장강도는 각 각 955.9Mpa과 220.4Mpa이다. 육성용접층과 모재의 미소경도는 각 각 $485.5{\pm}21$과 $197.4{\pm}14$ 이었고, 육성용접층은 매우 높은 경도를 갖는다. 모재는 조대한 결정립을 갖는 미세 구조를 나타내었다. 인장시험 후 파단면을 고분해능주사전자현미경으로 관찰한 결과 육성용접층과 모재의 파괴형태는 각각 취성파괴와 연성파괴를 나타내었다.